Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for SystemBase C510ip-s
Summary of Contents for SystemBase C510ip-s
- Page 1 SystemBas IP Audio Codecs USER MANUAL C510ip-s Page 1 REL300 upwards...
-
Page 2: Table Of Contents
Table of Contents INTRODUCTION............3 B ac k u p Mo nitor.......1 5 Key Features..........3 B ac k u p Th re s hold......1 5 Res tore Time........1 5 INSTALLATION............4 Reserve Dial........1 5 CONNECTIONS............4 Audio Source...........16 CONTROLS AND INDICATORS........4 Codec Function........16 VFD Display ..........4 ISDN Mode.........1 6 VU Meters..........4... -
Page 3: Introduction
INTRODUCTION The C510ip-s Audio Codec has been designed for the broadcast of high quality audio over digital networks, such as IP, ISDN, dedicated digital lines, optical fibre networks, digital microwave links and satellite links. To achieve an efficient utilisation of the available network data bandwidth, the C510ip-s can be configured to use L16, L24, G722, G711 or apt-X100 4:1 fixed audio encoding system to provide full duplex, point-to-point audio transmission. -
Page 4: Installation
Menu Scroll Up / Previous button. isolated, XLR connectors. Menu Scroll Down / Next button. 3/ ISDN: The C510ip-s supports ISDN on the slot labelled “ISDN 1/2”. Menu Select / Edit button is used to select the 4/ The C510ip-s supports AoIP streaming on the slot configuration which is to be modified. - Page 5 unit into the Patch Dial menu, allowing the user to MENU : Keypad Dial (Num) access 1 of 26 pre-stored configuration memories: 01256880123 MENU : Patch Dial PATCH 1 An optional sub-address can also be specified by use of the button.
-
Page 6: Front & Rear Panels
FRONT & REAR PANELS Page 6... -
Page 7: Menu Map
MENU MAP DOWN RIGHT / EDIT BACKSPACE CONFIRM EDIT CANCEL EDIT / LEFT DOWN RIGHT / EDIT BACKSPACE CONFIRM EDIT CANCEL EDIT / LEFT Page 7... -
Page 8: Ip Menu Map
IP MENU MAP DOWN RIGHT / EDIT BACKSPACE CONFIRM EDIT CANCEL EDIT / LEFT Page 8... -
Page 9: Menu System
(Nailed Up Mode) button may be used to display information about the AES input data stream. Note: If the C510ip-s is configured in X.21 Mode, the ISDN port can still function, however the audio will not be routed INFO: Aes Status through to the ISDN connector. -
Page 10: Select Patch
MENU: Patch Name MENU: ISDN Audio Mixing LONDON STUDIO 2 The C510ip-s codec can be configured to digitally monoise the selected audio source, by mixing the Left and Right signals with a 6dB pad. The monoised signal is replicated to both Analogue and Digital AES3 Left and Right output channels. -
Page 11: Audio Priority
NO button to The ISDN parameters associated with each ISDN B abort the changes. Channel can be changed. The C510ip-s has 2 ISDN B Channels. The following 3 option menus are repeated for all available Channels. -
Page 12: Isdn Msn
ISDN MSN The IP Remote Address or Domain name can be entered using the numerical keypad. The button backspaces to edit a number once it has been MENU: CH1 MSN confirmed. On completion press the YES button to save the changes, and the NO button to abort the changes. -
Page 13: Ip Link 1 Format
IP Link 1 Format IP Link 1 AutoCon MENU: IP LINK 1 FORMAT MENU: IP LINK 1 AUTOCON Stereo The Audio Format of the audio can be selected. The C500ip can be configured to Auto-Connect if Mono the IP connection is disrupted for any reason Stereo including power reset. -
Page 14: Ip Local Gateway
MENU: IP GROUP ID displayed as shown above. 1234 IP Local Gateway The IP Group ID is associated with the Systembase MENU: IP LOCAL GATEWAY AoIP protocol and used to prevent the C510ip-s 198.0.0.22 (dhcp) Codec from accepting IP connection requests from unknown sources. -
Page 15: Sip Remote Port
APTX: 15K2 Stereo 256Kbps Reserve Dial buttons can be used to select the MENU: Reserve Dial required X21 Audio format: APTX: 22K5 Stereo 384Kbps APTX: 15K2 Stereo 256Kbps The C510ip-s can be configured to automatically APTX: 22K5 Mono 192Kbps Page 15... -
Page 16: Audio Source
X.21 line. The X.21 the currently selected patch (i.e. patch+1). Restore occurs following 10 seconds of continuous This function is only active when the C510ip-s is error free, test data transmissions on the X.21 line. configured for Backup Master mode. -
Page 17: Auxiliary D A T A Por
The Auxiliary Data Port can be configured for the MENU: ISDN Network Euro ETSI following modes: Off, 9600bps, 4800bps, The C510ip-s can be re-configured to operate on 1 2400bps, of 12 International ISDN Standards: 9600bps(alt), APT compatible 4800bps(alt), APT compatible Euro ETSI 2400bps(alt), APT compatible China Relay Mode. -
Page 18: Loopback
- the YES button is is selected to ON the C510ip-s will request a disabled. Edit Lock enables ISDN calls to dialled temporary IP Address from the IP Server and and hanged. Full Lock disables ISDN dial and hang, thereby simplifying the setup process. -
Page 19: Email Alert Messages
SIP Registration SIP stands for Session Initiation Protocol and is used by devices that wish to establish Multimedia SIP registration is supported on the C510ip-s audio Sessions. Equipment manufacturers that support codec. However, it can only be accessed via the SIP will have the ability to connect with each other in WEB GUI. -
Page 20: Web Server
A Windows Login screen will be displayed. The default Username is “admin” and the default password is “admin”. If you wish to disable the password prompt then simply leave the password field blank. The screen shots below shows the layout of the Webserver for the C510ip-s Codec. Page 20... -
Page 21: Easymon Network Monitor
EasyMON is a free network monitor tool that allows an organisation to monitor multiple codecs in a single browser window with minimal overhead. EasyMON is free, and maybe downloaded from the systembase website, www.systembase.com. Included in the download are instructions that will guide you through the correct configuration. -
Page 22: Remote Management
REMOTE MANAGEMENT G722:7K5 Dual 64Kbps, APTX:3K7 Stereo 64Kbps, APTX:7K5 Mono 64Kbps, The C510ip-s Codec can be configured remotely by APTX:7K5 Stereo 128Kbps, connecting a straight 9 Way D-Type cable to the APTX:15K2 Mono 128Kbps, MGR IP port, and using the Standard Windows HIT-APTX:7K5 Stereo 128K, Terminal Program. -
Page 23: Physical Connections
PHYSICAL CONNECTIONS IP Port (ISDN 3-4) Analogue Audio 100B-TX full-duplex The audio interface presents balanced stereo XLR 100B-TX half-duplex inputs and outputs. The electrical characteristics of IP Interface 10B-TX full-duplex these connections is detailed below :- 10B-TX half-duplex Unicast / Simulcast I/P Impedance >10K Ohms I/P Level... -
Page 24: X.21 Port
X.21 Port Manager Output Port The electrical characteristics and the pin out of the Type V.24/RS232 - Fixed DTE connector is detailed below:- Speed 9600bps (8,n,1) Signals TXD, RXD, SIG GND X.21 Type Fixed DTE Connector 9-way Dsub Female X.21 Speed 64Kbps to 384Kbps X.21 Signals C, I, TXD, RXD, CLK... -
Page 25: Remote Trigger
* Remote Trigger Input - Do Not Connect to Voltage Outputs. CE COMPLIANCE Alarm Signal Systembase Limited hereby declares that this The C510ip-s provides a set of alarm relay contacts product is in compliance with the Electromagnetic with a minimum of 0.5 second duration. These relay Compatibility Directive 2004/108/EC. - Page 26 Information furnished is believed to be accurate and reliable at the time of publication. The manufacturer reserves the right to change details without notice. Systembase is a trademark of Systembase Limited. apt- X is a trademark of APT Licensing Ltd. All trademarks and tradenames acknowledged. This document is not part of a contract or licence except as may be expressly agreed in writing.
Need help?
Do you have a question about the C510ip-s and is the answer not in the manual?
Questions and answers