Related Manuals for NXP Semiconductors IOTZTB-DK006
Summary of Contents for NXP Semiconductors IOTZTB-DK006
- Page 1 UM11393 IOTZTB-DK006 Development Kit User Guide Rev.3.0 — 9 March 2021 Document information Info Content Keywords IOTZTB DK, User Guide Abstract This document is a user guide for the IOTZTB Development Kit...
- Page 2 Third version – Added support for K32W041AM and K32W041A 20210309 Contact information For more information, please visit: http://www.nxp.com UM1393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 2 of 23...
-
Page 3: Introduction
J-Link and J-Trace functions are all supported for debugging the devices. ISP download function is also contained and very easy to use. 1.1 Purpose This document introduces all functions of IOTZTB-DK006 and describes all parts of IOTZTB-DK006 boards in detail. 1.2 Kit contents IOTZTB-DK006 includes the following boards: •... -
Page 4: Carrier Main Board
On-board 3.3V from USB port, 4xAAA batteries, 2xAAA batteries (low-power mode) or external power supply options. UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 4 of 23... -
Page 5: Board Layout And Settings
In System Programming (ISP) LED indicator. LED is ON when SW2 button is pressed. Link2 MCU UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 5 of 23... - Page 6 User Interface button connected to IO1. Used in some Applications Notes. UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 6 of 23...
-
Page 7: Led Indicators
In System Programming (ISP) LED indicator. LED is ON when IO5_ISP is pulled low and when SW2 button is pressed. UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 7 of 23... -
Page 8: Arduino Connectors
Link USB connector (J15) must be disconnected. UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 8 of 23... -
Page 9: Debug Configurations
Jumper JP1 must be open or fitted across pin 2 – 3 to enable the target UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide... -
Page 10: On-Board Link2 Flash Programming
Fit jumper JP2 across pins 2 - 3 (External Target). UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 10 of 23... -
Page 11: K32W061/041 Upgrade Module Boards
Flash memory. Please refer to the schematic on the next figure for details. UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 11 of 23... -
Page 12: Generic Expansion Board
Carrier Board: D1 is connected to IO16 UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 12 of 23... - Page 13 R9 and R16). Figure 9 Generic expansion board UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 13 of 23...
-
Page 14: Light Expansion Board
1 Accelerometer & Magnetometer (IC9) connected by I2C Figure 10 Lighting expansion board UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 14 of 23... -
Page 15: K32W061 Usb Dongle
J14 on the PCB. The voltmeter positive probe is applied to J14 pin 1 UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide... -
Page 16: Current Measurement With A Multimeter
This signal goes to the module (JM1.17) and the expansion connector (J3.31) UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 16 of 23... - Page 17 To measure the current using multimeter, remove R51 and place the multimeter across J14 pins 1 and 2. Figure 14 R51 Location UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 17 of 23...
-
Page 18: Io Considerations
0, 1, 2, 3, 7 Negligible effect. Remove IC18 and IC24 UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 18 of 23... -
Page 19: Running The Dk6 Board At Different Voltages
The circuit is shown below in Figure 16 UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 19 of 23... - Page 20 It is important to leave C49 connected to Pin10 of the FT230A. To achieve this modify the boards as shown in Figure 17 Figure 17 3V3OUT modification UM11393 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 20 of 23...
-
Page 21: Legal Information
For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 03/2021 Document identifier: UM11393 UM11393 © NXP Semiconductors N.V. 2021. All rights reserved. Rev.3.0 — 9 March 2021 User Guide 21 of 23... -
Page 22: Table Of Contents
IOTZTB-DK006 NXP Semiconductors IOTZTB-DK006 Development Kit User Guide 10. Contents Introduction ............3 Purpose .............. 3 Kit contents ............3 Carrier Main Board ..........4 Feature summary ..........4 Board layout and settings ........5 LED indicators ............ 7 ARDUINO connectors ........8 Buttons ...............
Need help?
Do you have a question about the IOTZTB-DK006 and is the answer not in the manual?
Questions and answers