Table of Contents
Advertisement
General Operations
Reset the unit
When operating the unit for the first time,
after replacing the car battery or changing
the connections, you must reset the unit.
1.Turn off the unit power.
2.
Press the
OPEN
the front panel and remove it, then press
the
RESET
button with a ballpoint pen or
similar object to restart the unit.
Power on/off
In power off mode, switch on the unit by
pressing any button except the
button. When the system is on, press and
hold the
POWER
on/off button
2 sceconds to turn off the unit.
Sound adjustment
- Rotate the volume control to adjust
volume level.
- Press the
SEL
button short and repeatedly
to select the
the sound setting that you
would like to adjust:
balance and fader.
- Rotate the volume control to adjust level of
the selected sound mode:
- VOL:00,01 ~ 44,45
- BAS / TRE: -7, -6 ~,0, ~ +6,+7,
- BAL: 7R,6R, ~,0, ~, 6L,7L
- FAD: 7R, 6R, ~, 0, ~, 6F,7F
- Loudness: LOUD ON / OFF
- E
qualizer mode
: DSP OFF, POP, ROCK,
CLASSIC, FLAT
Note:
1. In each mode, w
adjusted for about 2 seconds, the current
setting will be saved and it returns to the
previous mode.
2. When using preset EQ modes, you
cannot have access to Bass and Treble
settings.
System menu
Press the
SEL
button and hold for more
than 2 seconds to access system setup
menu mode, then
momentarily to select the menu items in
sequence as follows:
"TA SEEK or TA ALARM"
g
MUTE"
"RETUNE L or RETUNE S"
button (
) to fold down
OPEN
(
)
for about
volume, bass, treble,
hen the unit has not been
press the
SEL
button
g
"PI SOUND or PI
"MASK DPI or MASK ALL"
(traffic announcement volume)
24 or 12" (Clock format)
(beep sound on/off
After selecting the desired menu item,
r
otate the volume control
of the selected item.
"TA SEEK or TA ALARM"
announcement/traffic announcement
alarm)
- TA SEEK mode:
When a newly tuned station does not
receive traffic information for 5 seconds,
(
)
the radio retunes to next station which has a
different PI and which broadcasts traffic
information.
If, during the chosen retune time (30
seconds for a short retune or 90 seconds for
a long retune), the unit can no longer
receive the current station which was
broadcasting traffic information, it will start
to search for the next station that has the
same PI.
If no station with the same PI is found after
one search cycle, the radio will search for
the next station broadcasting traffic
announcements.
- TA ALARM mode:
Select this mode to switch off the automatic
retune. The radio will bring up a warning
message "NO TP, TA" on the LCD display
and emit a double beep sound (ALARM).
If a newly tuned station does not broadcast
any traffic information for 5 seconds, a beep
can be heard.
If the unit can no longer receive the current
station during the chosen retune time, a
beep sound can also be heard.
If a newly tuned station has no RDS signal,
the message "PI SEEK" disappears.
Note:
"PI SOUND or PI MUTE":
In some regions, there is a possibility of
having two different stations with the same
frequency but different PI codes.
If "PI SOUND" is selected, radio will switch
to the new station with a different PI for a
few seconds before switching back to the
current station that was broadcast initially.
If "PI MUTE" is selected, the radio will not
broadcast the new station that is received.
g
g
g
)
EXIT
TP: Traffic Program.
PI: Program Identification.
g
"TAVOL 17"
g
"CLOCK
"BEEP ON/OFF"
to select the mode
(search for traffic
Advertisement
Table of Contents
