A8 Snmp Mib - Phihong PoE125U User Manual

A8 SNMP MIB:
Phihong USA Corp. registered Enterprise ID: 1.3.6.1.4.1.24852
SNMP Version: SNMP V2
TCP, UDP Port: 161 SNMP (Simple Network Management Protocol)
OID
1.3.6.1.4.1.24852.2.2.1.0
1.3.6.1.4.1.24852.2.2.2.0
1.3.6.1.4.1.24852.2.2.3.0
1.3.6.1.4.1.24852.2.2.4.0
1.3.6.1.4.1.24852.2.2.6.0
1.3.6.1.4.1.24852.2.2.7.0
1.3.6.1.4.1.24852.2.2.8.0
1.3.6.1.4.1.24852.2.2.10.0
1.3.6.1.4.1.24852.2.2.11.0
1.3.6.1.4.1.24852.2.2.12.0
1.3.6.1.4.1.24852.2.2.13.0
1.3.6.1.4.1.24852.2.2.14.0
1.3.6.1.4.1.24852.2.2.15.0
1.3.6.1.4.1.24852.2.3.1.1.
1~24
1.3.6.1.4.1.24852.2.3.1.2.
1~24
Phihong USA Corporation • East Coast Engineering Center • 630 Johnson Ave. Suite 102, Bohemia, NY 11716 • Tel: (631) 610-2289
Name
poeSystemActionHubReset
poeSystemActionHubRestoreFa
ctoryDefault
poeSystemActionHubSaveConfi
guration
poeSystemAllPortPowerEnable
poeSystemHWVersion
poeSystemNumberOfChannel
poeSystemProductPartNumber
poeSystemFirmwareVersion
poeSystemDescription
poeSystemConsumptionPower
***
poeSystemControlACPower ***
poeSystemControlDCPower ***
poeSystemControlBothPower
***
poePortIndex
poePortPowerEnable
www.Phihong.com
Type Value
INTEGER ready(0)
reset(1)
INTEGER ready(0)
restore(1)
INTEGER ready(0)
save(1)
INTEGER ready(0)
disable(1)
enable(2)
DisplayString Read-only
INTEGER Read-only
INTEGER Read-only
DisplayString Read-only
DisplayString Read –
(SIZE (0..10)) Write
INTEGER Read-only
INTEGER Read –
Write
INTEGER Read –
Write
INTEGER Read –
Write
INTEGER Read-only
(1..2147483647)
INTEGER disable(1)
enable(2)
or www.Midspans.com
44
1
Description
Reset the POE controller
Restore Factory Defaults
Save the POE parameters to
flash
Setting this object at a value
enable(2) enables detection
mechanism for all port.
Setting this object at a value
disable(1) disables detection
mechanism for all port.
System hardware version for
the Main board
Number of ports available in
the system
Number of ports
System firmware version for
the POE
System Description, max.
length of 10 characters
Measured power usage
expressed in Watts
Sets the value of available
power in Watts to be supplied
by primary(AC) power source.
Sets the value of available
power in Watts to be supplied
by secondary(DC) power
source
Sets the value of the total
available power in Watts to be
supplied by both power
sources.
A unique value for each port
Setting this object at a value
enable(2) enables the detection
mechanism for this port.