Honeywell LYNX Touch L7000 Series User Manual page 66

6<67(0 )81&7,216 6<67(0 )81&7,216 6<67(0 )81&7,216 6<67(0 )81&7,216
7HVWLQJ WKH 6\VWHP WR EH FRQGXFWHG ZHHNO\
Ready To Arm
Prod. Id. : XXXX Sw. Rev.: XX.XX
CRC Number: XXXX
RF Version Number: XXXXXX
WiFi Ver: X.X.X
Walk Test Comm. Test
Walk Test
)$8/7 =21(6 2SHQ HDFK SURWHFWHG GRRU DQG ZLQGRZ LQ WXUQ DQG OLVWHQ IRU WKUHH EHHSV IURP WKH FRQWURO
IROORZHG E\ WKH ]RQH·V 9RLFH 'HVFULSWRU LI LW LV SURJUDPPHG ,GHQWLILFDWLRQ RI HDFK IDXOWHG SURWHFWLRQ SRLQW
VKRXOG DSSHDU RQ WKH GLVSOD\ 7KH GLVSOD\ ZLOO FOHDU ZKHQ WKH GRRU RU ZLQGRZ LV FORVHG
:DON LQ IURQW RI DQ\ LQWHULRU PRWLRQ GHWHFWRUV LI XVHG DQG OLVWHQ IRU WKUHH EHHSV DQG RU YRLFH GHVFULSWRUV LI
SURJUDPPHG 7KH LGHQWLILFDWLRQ RI WKH GHWHFWRU VKRXOG DSSHDU RQ WKH GLVSOD\ ZKHQ LW LV DFWLYDWHG DQG LWV YRLFH
GHVFULSWRU ZLOO EH DQQRXQFHG LI SURJUDPPHG 7KH GLVSOD\ ZLOO FOHDU ZKHQ QR PRWLRQ LV GHWHFWHG 1RWH WKDW LI
ZLUHOHVV PRWLRQ GHWHFWRUV DUH XVHG LQ RUGHU WR FRQVHUYH EDWWHU\ OLIH WKHUH LV D
DFWLYDWLRQV
7R WHVW DOO VPRNH GHWHFWRUV IROORZ WKH PDQXIDFWXUHU V LQVWUXFWLRQV 7KH LGHQWLILFDWLRQ RI HDFK GHWHFWRU VKRXOG
DSSHDU RQ WKH GLVSOD\ ZKHQ HDFK LV DFWLYDWHG
,I D SUREOHP LV H[SHULHQFHG ZLWK DQ\ SURWHFWLRQ SRLQW QR FRQILUPLQJ VRXQGV QR GLVSOD\ QRWLI\ \RXU VHUYLFH
FRPSDQ\
:KHQ DOO SURWHFWLRQ SRLQWV KDYH EHHQ FKHFNHG DQG DUH LQWDFW FORVHG WKHUH VKRXOG EH QR ]RQH LGHQWLILFDWLRQ
QXPEHUV GLVSOD\HG RQ WKH WRXFK VFUHHQ
Test Communications
'HSHQGLQJ XSRQ WKH &RPPXQLFDWLRQ GHYLFH WKDW LQVWDOOHG LQ \RXU V\VWHP WKH IROORZLQJ RSWLRQV PD\ EH
GLVSOD\HG 6HOHFW WKH GHVLUHG RSWLRQ WR VHQG D WHVW DODUP WR WKH &HQWUDO 6WDWLRQ
•
Test Ethernet
,I WKH WHVW LV VXFFHVVIXO WKH 6\VWHP GLVSOD\V Service OK
•
Send Any
•
Send GSM Message
•
Send Ethernet Message
,I WKH WHVW LV VXFFHVVIXO WKH 6\VWHP GLVSOD\V Test Message Sent
,I WKH WHVW LV QRW VXFFHVVIXO WKH 6\VWHP GLVSOD\V Test Message Failed – Not Registered!
Exiting Test Mode
:KHQ WHVWLQJ LV FRPSOHWHG H[LW WKH :DON 7HVW 'LDOHU 7HVW RU &RPP 7HVW PRGH E\ VHOHFWLQJ WKH +RPH NH\ DQG
HQWHULQJ WKH 0DVWHU 8VHU &RGH LI UHTXLUHG
NOTE: If the Walk Test mode is inadvertently left active, it automatically turns off after 4 hours. The Dialer Test mode will remain
active until exited by selecting the "Home" key and entering the Master Code.
/<1; 7RXFK ([LW (QWU\ 'HOD\ 7LPHV
7KH /<1; 7RXFK ZLOO VHQG DQ HYHQW FRGH WR WKH &HQWUDO 6WDWLRQ DIWHU HQWHULQJ DQG DIWHU H[LWLQJ IURP 7HVW
PRGH
4. Select the "Walk Test", "Comm. Test" or "Reboot" icon. If Walk
Test is selected proceed to Step 5. If Comm. Test is selected
proceed to Step 6. If Reboot is selected proceed to Step 7.
5. "Walk Test..." is displayed on the system status bar and the
control sounds a single beep every 30 seconds. Fault each
zone as described below.
6. The system will advance to the Communications Test Screen.
Refer to the Communications Test paragraph.
Reboot
7. The system will reboot itself.
Back
8. After the reboot sequence is completed, conduct a Walk Test
7000-100-028-V0
to verify that all transmitters are operational in the system.
² ²
PLQXWH GHOD\ EHWZHHQ