Honeywell LYNX Touch L7000 Series User Manual page 59

Video Camera Controls
7KH FRQWUROV WKDW DUH DYDLODEOH DUH GHSHQGHQW XSRQ WKH FDPHUDV WKDW DUH LQVWDOOHG ZLWK \RXU V\VWHP 2QO\ WKRVH
FRQWUROV WKDW DUH DSSOLFDEOH WR WKH VSHFLILF FDPHUD ZLOO EH GLVSOD\HG
To control a camera:
To view/control a single camera:
To position a pan/tilt camera:
Button
Video Camera Control
1 2
Button operation is dependent upon the features available in the camera that is installed/selected (i.e.;
pan & tilt and auxiliary LED light). Only the buttons that are applicable for the selected camera are
3 4
displayed.
Camera "Home" position - The camera's home position is centered in its vertical and horizontal axis.
• When a camera has been moved to other than the home position, after 5 minutes of no movement
Notes
Preset buttons 1, 2, 3, 4 – These buttons are used to quickly drive the camera to a preset watch area.
1 2
(Up to 4 preset watch areas can be set.) Select the button to go to the preset watch area. To set a
preset watch area, use the arrow buttons to drive the camera to the desired area. Then tap the desired
3 4
1, 2, 3, or 4 button three times. The selected button will be highlighted (for around 5 seconds)
confirming that the preset is saved.
Arrow buttons – Used to position a PT (pan & tilt) camera. Select to incrementally position a pan & tilt
camera (i.e; iPCAM-PT) in a vertical or horizontal direction.
Center home button – Click to drive the camera to its home position.
Light – Used to toggle on or off the camera's auxiliary lighting LEDs. Depending on the ambient low
light conditions, the auxiliary lighting can improve video quality up to 15 feet.
Auto pan – Causes the camera to swing through its entire horizontal range. At the end of the panning
motion, the camera will return to the starting position. After 5 minutes of no movement the camera will
always return to the home position.
Video Camera – When selected, the panel displays a list of available video cameras.
Return/Home – Returns the control panel to the panel's Home Screen
Video Camera Indicators
Displayed Text
"Name" OR Camera information
"Name" OR Camera information
"Wait for Automatic Video Restore..."
"Double Tap to Restore Video"
"Video No Longer Available"
Date & Time
Tap one time on the video display from the camera you wish to control. The
LYNX Touch displays the camera controls that are avaiable for the selected
camera.
Tap two times on the video display from the camera you wish to control. The
LYNX Touch displays a full screen view of the video and the camera
controls that are avaiable for the selected camera. Tap the video display two
times again to return to multiple camera viewing.
Pan/tilt cameras can be positioned using the arrow or home button OR by
sweeping a finger across the screen, horizontally, vertically or diagonally to
drive the camera in that direction.
the camera will always return to the home position.
• Additional features can be programmed via TotalConnect 2.0. Check with your installer to see
which features are available.
• In the event that video is lost, frozen or is pixelated and does not automatically reset, tap the
display two times to manually restore the video.
Band
Green Normal operation, selected camera
Gray Normal operation, unselected camera
Blue Displayed after communication has been restored. After a delay, Video
restoration will begin automatically. The video can also be restored manually
by tapping the display two times.
Yellow Video restoration requires user to tap the display two times. Video will begin
when communications is restored.
Red Comunication with camera has been lost
Black Displayed if programmed
9LGHR &DPHUD &RQWURO )HDWXUH
Function
Meaning
² ²
86(5 )81&7,216 86(5 86(5 86(5 )81&7,216 )81&7,216 )81&7,216