Mitsubishi Electric PUHZ-ZRP35VKA Service Manual page 96

(2) Functions available when setting the unit number to 01-03 or AL (07 in case of wireless remote controller)
• When setting functions for an indoor unit in an independent system, set the unit number to 01 referring to 4 setting the
indoor unit number of Operating Procedure.
• When setting functions for a simultaneous- Twin Triple indoor unit system, set the unit number to 01 to 03 for each indoor
unit in case of selecting different functions for each unit referring to 4 setting the indoor unit number of Operating Procedure.
• When setting the same functions for an entire simultaneous Twin Triple-indoor unit system, set refrigerant address to AL (07
in case of wireless remote controller) referring to 4 setting the indoor unit number of Operating Procedure.
Function
Filter sign 100h
2500h
No filter sign indicator
Quiet
Air flow
Standard
( Fan speed )
High ceiling
No.of air outlets 4 directions
3 directions
2 directions
Optional high efficiency Not supported
Supported
filter
No vanes ( Vane No.3 setting : PLA only )
Vane setting
Vane No.1 setting
Vane No.2 setting
Not supported
Optional humidifier
( PLA only )
Supported
Vane differential setting No.1 setting ( TH5: 24-28°C )
No.2 setting ( Standard , TH5:28-32°C ) 14
in heating mode
( cold wind prevention ) No.3 setting ( TH5: 32-38°C )
Swing Not available Swing
Available
Set temperature in heating Available
mode ( 4 deg up ) *1
Not available
Fan speed during the Extra low
heating thermo OFF Stop
Set fan speed
Set fan speed
Fan speed during the
Stop
cooling thermo OFF
Detection of abnormality of Available
the pipe temperature ( P8 ) Not available
*1. PKA-HAL/KAL: 2 deg up
PEAD-RP JA(L)Q
•
Function
Filter sign 100h
2500h
No filter sign indicator
External static pressure 35/50/70/100/150Pa
External static pressure 35/50/70/100/150Pa
Set temperature in heating Available
mode ( 4 deg up )
Not available
Fan speed during the Extra low
heating thermo OFF Stop
Set fan speed
Fan speed during the
Set fan speed
cooling thermo OFF
Stop
Detection of abnormality Available
of the pipe Not available
Mode No.11
Setting No. Settings
Vane No.3 setting
1
No Vanes
2 Vane No.1 setting
3 Vane No.2 setting
* Be careful of the smudge on ceiling.
OCH527B
Setting
Mode
Settings
No. No.
1
07 2
3
1
08 2
3
1
09 2
3
1
10
2
1
11 2
3
1
13
2
1
2
3
}
1
PLA-BA
23
2
Wave air flow
1
24
2
1
25 2
3
1
27
2
1
28
2
Setting
Mode
Settings
No. No.
07
Refer to the right table
08
Refer to the right table
10
24
25
27
28
PLA-BA
Less smudging
( Downward position than the standard )
Standard
Less draft * (Upward position than the standard) Less draft * (Upward position than the standard)
: Initial setting ( Factory setting )
4-Way
Ceiling suspended
cassette
PLA-BA
PCA-KAQ PCA-HAQ
—
—
—
—
—
: Initial setting
External static
( Factory setting ) pressure
1 35Pa
50Pa
2
3 70Pa
100Pa
150Pa
1
2
1
2
3
1
2
1
2
No vane function
Standard
96
- : Not available
Wall mounted
PKA-HAL PKA-KAL
— —
—
— —
— — —
— — —
—
— —
— — —
— — —
— — —
— — —
— — —
— — —
— — —
—
—
—
—
—
Setting No.
Mode No. 08 Mode No. 10
2 1
3 1
2
1
2 2
3 2
PCA-KAQ
Floor
standing
PSA-KA
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Initial setting
( Factory setting )