Care And Use - Emerson InSinkErator F-HC3300C Installation Manual

7
FILL TANK & THEN CONNECT POWER
A
Scalding Hazard: The tap dispenses water up to
98ºC, which can instantly cause scalds or burns.
Use care when operating this appliance.
Dispensing Hot Water Dispensing Cool Water
(HC3300, H3300) (HC3300)
Scalding Hazard: The tap dispenses
water up to98ºC, which can instantly
cause scalds or burns. Use care when
operating this appliance.
B
NOTICE
Property Damage: Do not use an extension cord set
with the dispenser. (A standard grounded outlet within
760mm of the dispenser is required under the sink.)
■ Turn on the cold water supply.
■ Depress the tap's HOT handle and hold
it until water flows from the spout. Run
the water for at least 3 minutes to flush
lines (both the hot and cold handles on
HC2215 & HC1100 independently).
Note: See box below for special
instructions on operation of HC3300 and
H3300 taps.
Operating Instructions for HC3300 and H3300 taps
Featuring two-step hot side activation with
automatic shut off and cool side two-step
activation, which keeps the tap open when
dispensing cool water.
■
HC3300: To dispense instant
hot water, first press down on the
tap handle and then push the handle
backward in the direction of the red
indicator on the top of the handle. To
dispense cool water, first press down
on the tap handle and then pull the
handle forward in the direction of the
blue indicator on the handle.
Featuring two-step hot side activation with
automatic shut off.
■
H3300: To dispense instant hot water,
first press down on the tap handle and
then push the handle backward in the
direction of the red indicator on the top
of the handle.
■
Check all connections to ensure they
are tight and that there are no leaks.
■
Plug in instant hot water tank and
ensure that green light on front of tank
is illuminated.
Water will be cold at first.
Allow 12-15 minutes for water to reach target
temperature.
Gurgling or hissing is normal during the initial
heating cycle.

CARE AND USE

Electric Shock Hazard: To prevent electrical shock, disconnect power before servicing
unit. Use only a properly earthed (grounded) and polarized electric outlet.
ADJUSTING THE THERMOSTAT
approx. 96°C
Factory temperature pre-set is
96˚C. To reset the thermostat
to 96°C, turn the indicator one
notch to the right of vertical.
After adjusting, depress the tap
handle for 20 seconds for water
to re-heat to the new setting.
■
To adjust water temperature, turn
thermostat dial on the front of the tank
clockwise to increase temperature
or turn anticlockwise to decrease
temperature. Repeat if necessary.
All changes should be minimal.
Scalding Hazard: Do not allow water
to boil. May result in severe burns.
SEASONAL STORAGE/DRAINAGE
Anytime the steaming hot water tap is not used for
extended periods of time, unplug and drain unit. If
it is below freezing you will need to unplug the unit
and drain it.
■ Disconnect power from unit (unplug unit).
■
Push hot water tap lever and allow water
to flow until it is cool.
■
Shut the cold water tap off at the valve.
■
Disconnect tubes from the tank.
■ Unhook tank from wall.
■
Hold tank upside down and drain the
water into the sink.
■
Towel dry any water drippings from
tank area.
■ Reinstall tank to wall and
reconnect tubes.
■ Remove and discard filter cartridge,
if applicable.
■
To put back into working order, install
new filter cartridge (if applicable) and
turn on cold water supply at valve.
Depress the hot water dispenser faucet
lever and hold until water flows from the
spout. Reconnect the electrical cord.
CLEANING THE TAP AND TANK
■
Only use mild cleaners to clean the tap
and plastic components.
■
Cleaners with acids, abrasives, alkaline,
and organic solvents will result in
deterioration of the plastic components
and void the warranty.
FILTER GUIDE AND REPLACEMENT
Replace filter cartridge when there is an obvious
decrease in water flow to the tap or if there is an
objectionable taste or odour to the water.
When the inlet and outlet ports have been closed
and the filter's internal pressure has been relieved,
water (about 60ml) will discharge from vent line.
If the new filter cartridge cannot be inserted,
insert the old one and turn until it stops, remove it
and then retry the new cartridge.
It is recommended that carbon filters be replaced
every 6 months.
Filter replacement instructions:
■
Replace with an InSinkErator filter.
®
■
Place pan or dish towel under the filter to
catch water drainage during change.
■ Slowly turn the cartridge anticlockwise
completely until it stops (1/4 turn).
■
Pull cartridge straight down and discard.
■
Insert new cartridge into filter head.
■ Top surface of cartridge will become
flush with the bottom of the filter head
when fully engaged.
■
Turn the cartridge clockwise until it stops
(1/4 turn).
■ Align the in/out arrow on the head and
bracket assembly to the in/out arrow on
the cartridge.
■
Open tap to expel trapped air.
Run water for 3 minutes before usage.
■
Personal Injury:
• Regularly check for signs of corrosion by
examining the appearance of the dispensed water
every three (3) months.
• If there is any discoloration or rusty appearance,
unplug and drain unit as described in the Seasonal
Storage/Drainage section on this page of the
manual.
• If the water discoloration remains after draining
and refilling unit, discontinue use and contact an
authorized InSinkErator service agent.
5