Chapter 3 Programming The Basic Function; Input - Brainchild BTC-2500 User Manual

Chapter 3 Programming the Basic Function

Chapter 3 Programming the Basic Function
This unit provides an useful parameter " FUNC " which can be used to select This unit provides an useful parameter " FUNC " which can be used to select
the function complexity level before setup. If the Basic Mode ( FUNC = BASC ) the function complexity level before setup. If the Basic Mode ( FUNC = BASC )
is selected for a simple application, then the following functions are ignored is selected for a simple application, then the following functions are ignored
and deleted from the full function menu: and deleted from the full function menu:
RAMP , SP2, PB2, TI2, TD2, PL1, PL2, COMM, PROT, ADDR, BAUD, DATA, RAMP , SP2, PB2, TI2, TD2, PL1, PL2, COMM, PROT, ADDR, BAUD, DATA,
PARI, STOP , AOFN, AOLO, AOHI, IN2, IN2U, DP2, IN2L, IN2H, EIFN, PVMD, PARI, STOP , AOFN, AOLO, AOHI, IN2, IN2U, DP2, IN2L, IN2H, EIFN, PVMD,
FILT, SLEP , SPMD and SP2F. FILT, SLEP , SPMD and SP2F.
Basic Mode capabilities: Basic Mode capabilities:
(1) Input 1: Thermocouple, RTD, Volt, mA (1) Input 1: Thermocouple, RTD, Volt, mA
(2) Input 2: CT for heater break detection (2) Input 2: CT for heater break detection
(3) Output 1: Heating or Cooling ( Relay, SSR, SSRD, Volt, mA ) (3) Output 1: Heating or Cooling ( Relay, SSR, SSRD, Volt, mA )
(4) Output 2 : Cooling ( Relay, SSR, SSRD, Volt, mA ), DC Power supply. (4) Output 2 : Cooling ( Relay, SSR, SSRD, Volt, mA ), DC Power supply.
(5) Alarm 1: Relay for Deviation, Deviation Band, Process, Heater Break, Loop (5) Alarm 1: Relay for Deviation, Deviation Band, Process, Heater Break, Loop
Break, Sensor Break, Latch, Hold or Normal Alarm. Break, Sensor Break, Latch, Hold or Normal Alarm.
(6) Alarm 2: Relay for Deviation, Deviation Band, Process, Heater Break, Loop (6) Alarm 2: Relay for Deviation, Deviation Band, Process, Heater Break, Loop
Break, Sensor Break, Latch, Hold or Normal Alarm. Break, Sensor Break, Latch, Hold or Normal Alarm.
(7) Dwell Timer (7) Dwell Timer
(8) Heater Break Alarm (8) Heater Break Alarm
(9) Loop Break Alarm (9) Loop Break Alarm
(10) Sensor Break Alarm (10) Sensor Break Alarm
(11) Failure Transfer (11) Failure Transfer
(12) Bumpless Transfer (12) Bumpless Transfer
(13) PV1 Shift (13) PV1 Shift
(14) Programmable SP1 Range (14) Programmable SP1 Range
(15) Heat-Cool control (15) Heat-Cool control
(16) Hardware Lockout (16) Hardware Lockout
(17) Self-Tune (17) Self-Tune
(18) Auto-Tune (18) Auto-Tune
(19) ON-OFF, P , PD, PI, PID Control
(19) ON-OFF, P , PD, PI, PID Control
(20) User Defined Menu (SEL) (20) User Defined Menu (SEL)
(21) Manual Control (21) Manual Control
(22) Display Mode (22) Display Mode
(23) Reload Default Values (23) Reload Default Values
(24) Isolated DC Power Supply (24) Isolated DC Power Supply
(25) PV or SV Selection (25) PV or SV Selection

3 1 Input 1

3 1 Input 1
Press Press to enter Setup Mode. Press to enter Setup Mode. Press
display indicates the parameter symbol, and the lower display indicates the display indicates the parameter symbol, and the lower display indicates the
selection or the value of parameter. selection or the value of parameter.
IN1 : Selects the sensor type and signal type for Input 1. IN1 : Selects the sensor type and signal type for Input 1.
Range: Range: ( Thermocouple ) J_TC, K_TC, T_TC, E_TC, B_TC, R_ TC, S_TC, ( Thermocouple ) J_TC, K_TC, T_TC, E_TC, B_TC, R_ TC, S_TC,
( RTD ) PT.DN, PT.JS ( RTD ) PT.DN, PT.JS
(Linear ) 4-20, 0-20, 0-1V, 0-5V, 1-5V, 0-10 (Linear ) 4-20, 0-20, 0-1V, 0-5V, 1-5V, 0-10
L L
Default : Default : J_TC if F is selected, K_TC if C is selected. J_TC if F is selected, K_TC if C is selected.
IN1U: IN1U: Selects the process unit for Input 1. Selects the process unit for Input 1.
L L L L
Range: Range: C, F, PU ( process unit ) If the unit is neither C nor F, then C, F, PU ( process unit ) If the unit is neither C nor F, then
selects PU. selects PU.
L L L L
Default: Default: C or F. C or F.
DP1 : DP1 : Selects the location of the decimal point for most ( not all ) process Selects the location of the decimal point for most ( not all ) process
related parameters. related parameters.
Range: Range: ( For T/C and RTD ) NO.DP , 1-DP ( For T/C and RTD ) NO.DP , 1-DP
( For Linear ) NO.DP , 1-DP , 2-DP , 3-DP ( For Linear ) NO.DP , 1-DP , 2-DP , 3-DP
Default: Default: 1-DP 1-DP
40
to select parameter. The upper to select parameter. The upper
N_TC, L_TC N_TC, L_TC
L L
UM25001C
If you don't need: If you don't need:
(1) Second setpoint (1) Second setpoint
(2) Second PID (2) Second PID
(3) Event input (3) Event input
(4) Soft start (RAMP) (4) Soft start (RAMP)
(5) Remote set point (5) Remote set point
(6) Complex process value (6) Complex process value
(7) Output power limit (7) Output power limit
(8) Digital communication (8) Digital communication
(9) Analog retransmission (9) Analog retransmission
(10) Power shut off (Sleep Mode) (10) Power shut off (Sleep Mode)
(11) Digital filter (11) Digital filter
(12) Pump control (12) Pump control
(13) Remote lockout (13) Remote lockout
then you can use Basic Mode. then you can use Basic Mode.
L L L L
IN1
IN1U
DP1