Related Manuals for Evolution EVOMAG42
Summary of Contents for Evolution EVOMAG42
- Page 1 EVOMAG42 S28MAG Original Instructions EVOMAG42 shown without guards fitted for illustrative purposes only. Cutters not included Written in UK English Date Published: 23 / 07 / 2019...
-
Page 2: Evolution Limited Guarantee
Evolution Power Tools. Congratulations on your purchase of an Evolution Power Tools reserves the right to repair Evolution Power Tools Product. Please or replace it with the same or equivalent item. complete your product registration ‘online’... -
Page 3: Specifications
SPECIFICATIONS EVOMAG42 S28MAG MACHINE METRIC IMPERIAL METRIC IMPERIAL Motor (UK/EU) 230V - 240V ~ 50Hz 1200W Motor (UK/EU) 220V - 240V ~ 50HzV 1200W Motor (UK) 110V ~ 50Hz 1200W 1200W Motor (USA) 120V ~ 60Hz Number Of Speeds... -
Page 4: Labels And Symbols
It warning and/or instruction labels are missing is possible that the operator could develop or damaged. Contact Evolution Power Tools “Vibration white finger disease” (Raynaud for replacement labels. syndrome). This condition can reduce the... -
Page 5: Intended Use
• This power tool should be used in a times when using this tool. weather protected environment, and be used with the accessories provided, or Evolution Power Tools recommended Hard Hat—Head protection should be worn at all times whilst using this tool, accessories only. -
Page 6: Electrical Safety
www.evolutionpowertools.com WARNING: This machine is not intended to your mains-operated (corded) power tool for use by persons (including children) with or battery-operated (cordless) power tool. reduced physical, sensory or mental capabilities, or lack of experience and knowledge. 1) General Power Tool Safety Warnings Children should be supervised to ensure [Work area safety] that they do not have access to, and are not... - Page 7 www.evolutionpowertools.com 3) General Power Tool Safety Warnings and safer at a rate for which it was designed. [Personal Safety]. b) Do not use the power tool if the switch a) Stay alert, watch what you are doing does not turn it on or off. Any power tool and use common sense when operating a that cannot be controlled with the switch is power tool.
-
Page 8: Health Advice
www.evolutionpowertools.com HEALTH ADVICE to ensure that the mains power supply cannot be interrupted or compromised WARNING: When using this machine, dust accidentally. particles may be produced. In some instances, depending on the materials you are working Do not use other appliances on the same with, this dust can be particularly harmful. - Page 9 www.evolutionpowertools.com transportation/lifting handle. • Operate the crank handle to move the slide • Never carry the Magnetic Drill by the power up and down. There should be no free play, cord. Carrying the Magnetic Drill by the yet no binding anywhere throughout the power cord could cause damage to the range of travel.
-
Page 10: Getting Started - Unpacking
• Care should be taken with the ejected ITEMS SUPPLIED slug, this will be both hot and sharp, gloves should be worn when handling the slug. EVOMAG42 S28MAG DESCRIPTION Instruction Manual • This power tool can be used on a vertical... -
Page 11: Additional Accessories
ADDITIONAL ACCESSORIES In addition to the accessories supplied with this machine the following accessories are available from Evolution’s online shop at www.evolutionpowertools.com or from your local retailer. Description Part No Chuck Adaptor HTA 47 Chuck & Chuck Key 13mm... -
Page 12: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW MACHINE FITTED WITH MACHINE FITTED WITH ANNULAR CUTTER 3 JAW CHUCK 1. Magnet On/Off Switch 9. 3 Jaw Chuck 2. Motor On/Off Switch 10. Drill Bit (Not included) 3. Guard 4. Annular Cutter (Not included) 5. Secondary Slide Locking Lever 6. -
Page 13: Assembly And Preparation
WARNING: Mag Drills must not be connected to a power source until all assembly and preparation has been completed and a safety check carried out. Evolution Mag Drills should only to be used on non-coated Mild Steel which is free from paint or loose rust etc. - Page 14 • Check that the cutter securing grub screws located in the end of the spindle are not protruding into the spindle bore. (EVOMAG42 - Fig.8. ) (S28MAG - Fig.9) • Align the two ‘flats’ machined on the cutters shaft with the grub Fig.
-
Page 15: Installing A 3 Jaw Chuck
www.evolutionpowertools.com INSTALLING A 3 JAW CHUCK (UK Market only) A three (3) jaw chuck (part HTA 153) can be fitted into the drive spindle of S28MAG enabling the machine to take standard parallel shank twist drills up to Ø13mm (Ø1/2in). WARNING: Ensure that the machine is disconnected from the mains power supply when installing the 3 jaw chuck. - Page 16 www.evolutionpowertools.com WARNING: In the event of power disruption or failure the safety chain/strap ensures that the machine remains in place attached to the workpiece. (Fig12) As a crucial safety feature it must be securely attached to both the machine and to the workpiece. BEFORE beginning cutting operations the strap or chain must be correctly fitted, preferably passing through the machines carrying handle.
-
Page 17: Making A Cut
(3) jawed chuck and twist drill. GENERAL GUIDANCE Evolution Power Tools has no control over the way its machinery may be used. The following is offered as general (but not exhaustive or definitive) advice on the safe operation of MagDrill machines. -
Page 18: Environmental Protection
www.evolutionpowertools.com All motor bearings in this machine are lubricated • Use hex key (supplied) to loosen slightly the for life. No further lubrication is required. locking screws which lock the adjustable Gib in place. Use a clean, slightly damp cloth to clean the •... -
Page 19: Declaration Of Conformity
DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: UK: Evolution Power Tools Ltd. Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. FR: Evolution Power Tools SAS. 61 Avenue Lafontaine, 33560, Carbon-Blanc, Bordeaux, France. - Page 20 Evolution Power Tools Ltd Evolution Power Tools LLC Evolution Power Tools SAS Venture One 8363 Research Drive 61 Avenue Lafontaine Longacre Close Davenport 33560 Holbrook Industrial Estate Iowa Carbon-Blanc Sheffield 52806 Bordeaux S20 3FR +44 (0)114 251 1022 +1 866-EVO-TOOL...
Need help?
Do you have a question about the EVOMAG42 and is the answer not in the manual?
Questions and answers