Dubbing Mode - FUNAI WD6D-M101 Owner's Manual

Dubbing Mode

You can copy a DVD disc to a videotape or copy a videotape
to a DVD disc. This function will be possible only if the DVD or
the videotape is not copy protected.
Before dubbing, prepare for the recording on the DVDs or the
videotape. See pages 28-29 (DVD) or page 71 (VCR).
Note for recording to a videotape:
• The videotape's record tab is intact.
• The videotape is long enough to record the DVD disc.
Note for recording to a disc:
• The DVD disc is satisfied with the recording status. See
pages 28-29.
Insert a disc and a videotape with a record tab.
1
In stop mode, press [SETUP]. Select "General
Setting" using [K \ L], then press [ENTER\OK].
2 Select "Recording" using [K \ L], then press
[ENTER\OK].
3 Select "Dubbing Mode" using [K \ L], then
press [ENTER\OK].
Option window will appear.
VCR to DVD
4
Select "VCR A DVD" using [K \ L], then press
[ENTER\OK].
General Setting
Playback
Display Auto Chapter
Video Recording Audio Select (1H)
Recording
Auto Finalise
Dubbing Mode
Clock Aspect Ratio (Video mode)
VCR DVD
Channel
Dubbing Mode
DVD VCR
DivX
Bilingual Recording Audio
HDMI
External Input Audio
DVB Setting
Video Colour System
Reset All
5
Press [SETUP] to exit.
6
Press [VCR].
7
Press [PLAY B], and then press [PAUSE F]
where you want to start recording.
8
Press [DVD].
Make sure to select a recording speed using
[REC SPEED]. (See page 28.)
9
Press [DUBBING].
VCR to DVD duplication will start.
10
Press [STOP C] to stop the recording.
Note for VCR to DVD duplication:
• During duplication, recording will be paused when a
signal other than PAL or SECAM is detected. (See
"Video Colour System" on page 37 for details.)
• After starting VCR to DVD duplication, the picture may
be distorted because of the auto tracking function. This
is not a malfunction. Be advised to play back the tape
until the picture is stabilised, then set the starting point
at which you want to start recording, and start VCR to
DVD duplication.
40
EN
• This unit will automatically stop the duplication if
playback with no image detected for more than 3
minutes during VCR to DVD duplication.
• If the playback sound mode of VCR is set to "STEREO",
"LEFT" or "RIGHT", the sound mode upon dubbing is
automatically switched to "STEREO". If the playback
sound mode is set to "MONO", the sound mode upon
dubbing is also "MONO".
• If you set "External Input Audio" to "Stereo", the sound is
recorded in "Stereo" (video mode and VR mode).
• While in video mode, if you set "External Input Audio" to
"Bilingual", the audio set in "Bilingual Recording Audio"
mode is recorded. While in VR mode, if you set
"External Input Audio" to "Bilingual", bilingual audio is
recorded.
• The main and sub audio will be simultaneously recorded
(VR mode). You can select audio modes during
playback.
• If you want to watch the duplicated material, after the
VCR to DVD duplication, press [DVD] first then press
[PLAY B].
DVD to VCR
4
Select "DVD A VCR" using [K \ L], then press
[ENTER\OK].
General Setting
Playback
Display Auto Chapter
Video
Recording Audio Select (1H)
Recording
Auto Finalise
Dubbing Mode
Clock
Aspect Ratio (Video mode)
VCR DVD
Channel
Dubbing Mode
DivX DVD VCR
Bilingual Recording Audio
HDMI
External Input Audio
DVB Setting
Video Colour System
Reset All
5
Press [SETUP] to exit "Setup" menu.
6
Press [DVD].
7
Press [PLAY B], and then press [PAUSE F] at
the point you want to start recording.
8
Press [VCR].
Make sure to select a recording speed using
[REC SPEED]. (See page 71.)
Rewind or fast forward the tape to the point where you
want to start recording.
9
Press [DUBBING].
DVD to VCR duplication will start.
10
Press [STOP C] to stop the recording.
Note
• NTSC dubbing is prohibited in this unit.
• Dubbing mode is available only if the tape or disc is not
copy-protected.
• You cannot change the output mode during VCR to DVD or
DVD to VCR duplication.
• If you want to watch the duplicated material, after the DVD to
VCR duplication, press [VCR] first and then press [PLAY B].
• When "DV" is selected as input, DUBBING function cannot
be performed. DUBBING can be performed with either AV1
or AV2 inputs.