Table of Contents
Advertisement
Quick Links
®
1630
Earth Ground Clamp
Calibration Information
Introduction
This document provides the following information for the 1630 Earth Ground Clamp (hereafter
referred to as the Clamp or UUT):
• Safety information
• Symbols
• Specifications
• Maintenance
• Performance Tests
• Calibration Adjustments
• Product Warranty Statement
For complete operating instructions, refer to the 1630 Instruction Sheet.
Contacting Fluke
For warranty service, contact Fluke as follows:
USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
Or, visit Fluke's Web site at www.fluke.com.
To register your product, go to register.fluke.com.
October 2007
© 2007 Fluke Corporation. All rights reserved. Specifications are subject to change without notification.
All product names are trademarks of their respective companies.
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Fluke 1630
Summary of Contents for Fluke 1630
- Page 1 ® 1630 Earth Ground Clamp Calibration Information Introduction This document provides the following information for the 1630 Earth Ground Clamp (hereafter referred to as the Clamp or UUT): • Safety information • Symbols • Specifications • Maintenance • Performance Tests •...
-
Page 2: Safety Information
Battery or battery compartment. Low battery when shown on display. Conforms to requirements of European Union. Do not dispose of this product as unsorted municipal waste. Go to Fluke’s website for recycling information. Canadian Standards Association. Complies with Canadian and US Standards. - Page 3 Earth Ground Clamp Specifications Specifications General Specifications Conductor Size..........33 mm (1.3 in) approximately Dimensions (L x W x H) ........276 mm x 100 mm x 47 mm (10.8 in x 3.9 in x 1.9 in) Weight ..............750 g (1.65 lb) Electrical Specifications Display ...............
-
Page 4: Maintenance
The recommended calibration interval is 12 months. In the performance tests, the Clamp is referred to as the unit under test (UUT). If the UUT fails any performance test, contact Fluke Service for repair. See Contacting Fluke. - Page 5 Table 2 lists the required equipment to complete the performance tests. If the recommended models are unavailable, use equipment with equivalent specifications. Table 2. Required Equipment Equipment Minimum Required Characteristics Recommended Model Fluke 5520A High Performance AC current: Multi-Product Calibrator • Range 9 mA to 10 A ± 1.25 % Calibrator •...
- Page 6 5. Continue accuracy tests for the other functions listed in Table 3. If any display readings fall outside of the Display Reading Limits in Table 3, the UUT requires calibration adjustment or repair. See Contacting Fluke. Table 3. 1630 Accuracy Tests...
- Page 7 Earth Ground Clamp Performance Tests Table 3. 1630 Accuracy Tests (cont.) Display Reading Step Source Applied Value Function Limits/Instruction Press F and set the HI alarm to 40 Ω Press F to return to measurement function Clamp Beeps and Display shows 50 Ω...
-
Page 8: Calibration Adjustment
The UUT is now in the calibration adjustment mode. Refer to Figure 2 for adjustment locations and complete the adjustments as instructed in Table 4. If the UUT fails to meet any expected results, contact Fluke Service for repair. See Contacting Fluke. Table 4. Calibration Adjustment Steps... - Page 9 Earth Ground Clamp Calibration Adjustment Table 4. Calibration Adjustment Steps (cont.) Meter Applied Expected Step Action Source Adjust Function Value Result/Instruction Enter Cal Mode Harmonic displays Press Honce when 1 A / 60 Hz reading is stable. Press Honce when Calibrator and 6-in.
- Page 10 1630 Earth Ground Clamp Press tab and lift to remove battery holder from PCA. 6LR61 BATTERY Do not remove shield during adjustment. Shield removed for demonstration purposes only. Do not remove during adjustment. VR11 VR10 VR20 VR6 is not used fcy02.eps...
-
Page 11: Limited Warranty And Limitation Of Liability
Limited Warranty and Limitation of Liability Each Fluke product is warranted to be free from defects in material and workmanship under normal use and service. The warranty period is one year and begins on the date of shipment. Parts, product repairs, and services are warranted for 90 days. - Page 12 1630 Earth Ground Clamp...
Need help?
Do you have a question about the 1630 and is the answer not in the manual?
Questions and answers