Satel SATELLINE-M3-R9 Integration Manual
  1. Manuals
  2. Brands
  3. Satel Manuals
  4. Transceiver
  5. SATELLINE-M3-R9
  6. Integration manual

Satel SATELLINE-M3-R9 Integration Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SATELLINE-M3-TR8
SATELLINE-M3-TR9
TRANSCEIVER MODULES
SATELLINE-M3-R9 RECEIVER
MODULE
INTEGRATION GUIDE
Version 2.2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SATELLINE-M3-R9 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Satel SATELLINE-M3-R9

Summary of Contents for Satel SATELLINE-M3-R9

  • Page 1 SATELLINE-M3-TR8 SATELLINE-M3-TR9 TRANSCEIVER MODULES SATELLINE-M3-R9 RECEIVER MODULE INTEGRATION GUIDE Version 2.2...

  • Page 2: Important Notice

    Integration Guide, Version 2.2 IMPORTANT NOTICE All rights to this manual are owned solely by SATEL Oy (referred to in this user guide as SATEL). All rights reserved. The copying of this manual (without the written permission from the owner) by...

  • Page 3: Restrictions On Use - Satelline-M3-Tr8

    This device must not be co-located or operating in conjunction with any other antenna or transmitter. See www.satel.com for the newest Integration Guide version. Contact SATEL distributor or directly to SATEL for information regarding the latest FW release.

  • Page 4: Restrictions On Use - Satelline-M3-Tr9

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 RESTRICTIONS ON USE – SATELLINE-M3-TR9 SATELLINE-M3-TR9 radio transceiver module has been designed to operate on 902-928 MHz, the exact use of which differs from one region and/or country to another. The user of a radio transceiver module must take care that the said device is not operated without the permission of the local authorities on frequencies other than those specifically reserved and intended for use without a specific permit.

  • Page 5: Product Conformity

    Integration Guide, Version 2.2 PRODUCT CONFORMITY Hereby, SATEL Oy declares that SATELLINE-M3-TR8 radio transceiver module is in compliance with the essential requirements (radio performance, electromagnetic compatibility and electrical safety) and other relevant provisions of Directive 2014/53/EU. Therefore the equipment is labeled with the following CE-marking.

  • Page 6: Warranty And Safety Instructions

    -The radio transceiver module is only to be operated at frequencies allocated by local authorities, and without exceeding the given maximum allowed output power ratings. SATEL and its distributors are not responsible, if any products manufactured by it are used in unlawful ways.

  • Page 7: Host Integration

    This device has been modularly approved. Model name, FCC and Industry Canada identifiers of this product must appear on the outside label of the end-user equipment. Host labelling example: Model Name: SATEL-TA31 Contains FCC ID: MRBSATEL-TA31 IC: 2422A-SATELTA31 This device complies with part 15 of the FCC rules.

  • Page 8: Table Of Contents

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 TABLE OF CONTENTS IMPORTANT NOTICE ..................... 1 RESTRICTIONS ON USE – SATELLINE-M3-TR8 ............2 RESTRICTIONS ON USE – SATELLINE-M3-TR9 ............3 PRODUCT CONFORMITY ..................4 WARRANTY AND SAFETY INSTRUCTIONS ............. 5 HOST INTEGRATION ..................... 6 TABLE OF CONTENTS ....................
  • Page 9 Antenna interface ..................24 MECHANICAL CONSIDERATIONS ............25 Fixing device to host ................25 Module dimensions .................. 26 CONFIGURATION ................... 27 SATEL Configuration Manager software ..........27 Changing parameters using SL commands ..........28 6.2.1 SL Commands ......................28 6.2.2 SL Command Mode ....................
  • Page 10 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 10.2 Electrostatic discharge ................36 10.3 Using the device in unmanned high reliability applications ....36 APPENDIX A ................... 37 11.1 Sub-band Channel Assignment – SATELLINE-M3-TR8 ......37 11.1.1 Sub-band ......................... 37 11.1.2 Duty cycle .........................

  • Page 11: Introduction

    End users of SATEL products include both public organizations and private individuals. SATEL Oy is the leading European manufacturer of radio modems. SATEL radio modems have been certified in most European countries and also in many non-European countries.

  • Page 12: Technical Specifications

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 2. TECHNICAL SPECIFICATIONS Absolute maximum ratings Absolute maximum ratings for voltages on different pins are listed in the following table. Exceeding these values will cause permanent damage to the module. Parameter Voltage at VCC_IN +5 V (TR8), +6V (TR9) Voltage at ENA_MOD +6 V...

  • Page 13: Specifications, Satelline-M3-Tr8

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Specifications, SATELLINE-M3-TR8 SATELLINE-M3-TR8 complies with the following international standards: Frequency variant 868…870 MHz: EN 300 220-1, -2, EN 301 489-1, -3 and EN 60950-1. Frequency variant 865…867 MHz: EN 300 113-2. RECEIVER TRANSMITTER Note! 868...870 MHz...
  • Page 14 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 DATA MODULE CMOS-UART Inputs and outputs referred Electrical Interface to IO Voltage processed by user (1.8-3.3V) RTS, CTS, RX, TX, +VCC, GND Samtec 20-pin through Interface Connector 1.27 mm pitch socket hole, CLP-110-02-L-D-K-TR Data speed of Serial 9600 –...
  • Page 15 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Test condition �� = 4.0 V and �� = 25 °C ���� �� According to EN 300 220-2 V2.4.1 measurement setup. Higher values exceed the -36 dBm spurious limit at the antenna e.g. EN 300 220-2 requirement. Measured using Agilent 1147B current probe and TTi TSX1820P DC power supply.

  • Page 16: Specifications, Satelline-M3-Tr9

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Specifications, SATELLINE-M3-TR9 Receiver part specifications applies to SATELLINE-M3-R9 receiver module. SATELLINE-M3-TR9 complies with the following international standards: FCC Parts 15.209 and 15.247 of Title 47 IC RSS-247, ICC RSS-Gen AS/NZS 4268:2012, AS/NZS 4771:2000...
  • Page 17 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 DTE connector. ± 8 kV Acc. to EN61000-4- 2; 150pF/330Ω I-PEX 20279-001 -E- Antenna Connector 50 Ω, HIROSE U.FL compatible Construction PWB with sheet metal EMI shields Size L x W x T 57 x 36 x 6.9 mm Weight 20 g...

  • Page 18: Time Parameters For Startup And Shutdown Sequences

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 3. TIME PARAMETERS FOR STARTUP AND SHUTDOWN SEQUENCES The following table shows the recommend times for startup and shutdown sequences. Parameter Recom. Time Explanation >2 ms VCC_IN must be high before ENA_MOD is high vccin-ena >2 ms ENA_MOD must be high before VCC_IO is high...

  • Page 19: Shutdown And Ena Sequences

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Shutdown and ENA sequences The following diagrams will describe the shutdown and ENA sequences. vccio-vccin VCC_IN ENA_MOD enamod-gpio VCC_IO gpio-vccio GPIOx_INPUT CTS1_OUT GPIOx_OUTPU T Figure 3.2 Shutdown sequence. VCC_IN ENA_MOD enamod-cts VCC_IO gpio-vccio GPIOx_INPUT CTS1_OUT...

  • Page 20: Electrical Interconnection

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 4. ELECTRICAL INTERCONNECTION DTE connector The DTE connector is a 20-pin pass-through connector which provides electrical connections to the module. Connector is female two row 1.27 mm pitch. Figure 4.1 The side view of the module with connection directions. Figure 4.2 Pin numbering of 1.27 mm pitch DTE connector.

  • Page 21: Pin Order Of The Dte Connector

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Pin order of the DTE connector Direction IN is data from DTE (Data Terminal Equipment) to the radio transceiver module. Direction OUT is data from the radio module to the DTE. The equivalent I/O schematic figures are shown in the next chapter. Pin No.

  • Page 22: Equivalent I/O Schematics

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Equivalent I/O Schematics The module input-output equivalent circuits are shown in the figure and the component values in the table below. Figure 1 Figure 2 Input Filter protection Input VCC_IO Filter with ESD protection Filter protection...

  • Page 23: Vcc_Io Pin

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Component values of the equivalent schematics: Component Value Note 10 nF 1 nF 30 uF 2.2 uH 10 nF 1 nF 44 uF 15 uH 1000 Ω +- 25% Measured Impedance at 100 MHz 100 nF 1000 Ω...

  • Page 24: Stat Pin

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Stat pin The STAT-pin indicates the status of the device. It can be used to drive or sink a LED current using a proper series resistor. STAT-pin drive or sink capability is +/-10mA at 3.3 V. It is recommended to use VCC_IO for LED current.

  • Page 25: Antenna Interface

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 4.10 Antenna interface The antenna interface is a 50 Ω coaxial connector. Matching networks are not included on the module and should be placed in the host application if the antenna is not 50 Ω. The HIROSE U.FL compatible connector is located on the TOP side of the board.

  • Page 26: Mechanical Considerations

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 5. MECHANICAL CONSIDERATIONS Fixing device to host The M3-TR8 / M3-TR9 radio transceiver module can be mounted on to the host application by using spacers and screws. It is highly recommended to use conducting metal spacers and screws to create proper electrical conductivity between the module and the host application.

  • Page 27: Module Dimensions

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Module dimensions In figure below is a module with dimensions as millimeters. Figure 5.3 The module physical dimensions and the holes in millimeters.

  • Page 28: Configuration

    (see SL Command Mode). SATEL Configuration Manager software SATEL Configuration Manager is a PC software for the configuration of SATELLINE-M3-R/TR, SATEL-R/TR –module based radio models, covering most of the SATEL radio products. Minimum requirements: SATEL Configuration Manager PC-program COM port with baud rate min.

  • Page 29: Changing Parameters Using Sl Commands

    CR/LF characters are added to end the response messages (unless they are already present) in order to make parsing easier. Settings can be toggled, SL Commands ON/OFF, CR/LF ON/OFF. See Appendix B and C for SL commands. For information of the latest and/or special SL commands please contact SATEL.

  • Page 30: Command Mode

    The SL commands can be disabled or enabled by using SL commands or toggling the “SL Command mode” parameter via the SATEL Configuration Manager, version v1.3.15 or newer. By default the SL Command mode is set to ON. If the SL Command mode is set to OFF then the SL commands can be enabled or disabled by using the below described procedure.

  • Page 31: Operating Modes

    STAT pin in 250 ms interval indicating an Error and reboots the device after 5 s. Transmitting/Receiving is prohibited during malfunction. When connecting to the device with SATEL Configuration Manager the Error code is shown in pop up box. If the device does not recover after multiple reboots, please contact SATEL Oy.

  • Page 32: Sleep Mode

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Sleep Mode When being in sleep mode, the radio part of the module is switched OFF while the serial interface communication related parts remain powered ON. The module will be automatically woken up after the CPU senses a state change in the TD1 pin.

  • Page 33: Restart

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Transmission interval study is started over always after 100 successful sleep/wake-up cycles and, if the expected receiving slot (t ) with enhanced overlap margin (t ) has been missed. In RX slot overlap latter case the package is considered to be lost.

  • Page 34: Default Delivery Values - Satelline-M3-Tr8

    500 mW 10, 20, 50, 100, 200 and 500 mW Transmitter Output Power 1000 mW 10, 20, 50, 100, 200, 500 and 1000 mW Radio settings Radio Compatibility SATEL 3AS SATEL 3AS Addressing RX Address ON/OFF TX Address ON/OFF Serial port...

  • Page 35: Default Delivery Values - Satelline-M3-Tr9

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 9. DEFAULT DELIVERY VALUES – SATELLINE-M3-TR9 Receiver parts applies to SATELLINE-M3-R9 receiver module, forced permanently to Point to Multipoint Slave (RX Only) mode (cannot be changed). Operation Mode Default value Point-to-Multipoint Slave...

  • Page 36: Considerations

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 CONSIDERATIONS 10.1 EMI Interferers The module is designed to be mounted inside a host device. The module is designed to withstand EMI even beyond type approval requirements. However, a small module which is integrated closely to modern high speed electronics is bound to receive some interference.

  • Page 37: Electrostatic Discharge

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 10.2 Electrostatic discharge As the module is intended to be embedded in a host application, in a typical use case, the antenna port is the only port of the module directly interface with a surface or contact area subjected to Electrostatic Discharge (ESD).

  • Page 38: Sub-Band Channel Assignment - Satelline-M3-Tr8

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 11. APPENDIX A 11.1 Sub-band Channel Assignment – SATELLINE-M3-TR8 11.1.1 Sub-band Each sub-band is defined by a start and stop frequency. Furthermore, the maximum allowed power level and maximum duty cycle is defined separately for each sub-band. 11.1.2 Duty cycle The purpose of the duty cycle limit is to ensure that no single application can occupy this license-...

  • Page 39: Commands - Satelline-M3-Tr8

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 APPENDIX B 12.1 SL COMMANDS – SATELLINE-M3-TR8 Category Command Description Response Addressing SL#A? Show all addresses (RX1, RX2, TX1, "xxxx,yyyy,zzzz,vvvv" TX2) Addressing SL#A=xxxx, yyyy, Set RX/TX addresses (RX1, RX2, TX1, “OK" or "ERROR" zzzz,vvvv TX2) Addressing...
  • Page 40 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 ChannelList SL$D=n Set channel list default channel, n is “OK" or "ERROR" channel number ChannelList SL$E=1 Search free channel "OK" followed by “channel n Modem searches for next traffic-free is free” channel. Listening time of traffic is Value of n is channel number about 2 seconds of next free channel on...
  • Page 41 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 ChannelList SL$S=<selection> Set channel scanning mode. Selection: "OK" followed by S0 = Stop scanning (supported only by channel/RSSI info TR3/TR4/TR8) See a separate description for S1 = Starts Scanning RSSI values of the more details channels in the Channel list (supported only by TR3/TR4/TR8)
  • Page 42 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 otherwise data and carriage return ModemInfo SL%4="data" Set arbitrary data (max 25 characters) “OK" or "ERROR" in memory location 4 ModemInfo SL%C? Get product number (or other Depends on setup customer info) ModemInfo SL%C=”text Sets p/n (or other customer info) if it is...
  • Page 43 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 For conventional reasons, only 2 or 4 digit inputs are valid RadioFreq SL&-=nnnn Set active frequency nnnn channels “OK" or "ERROR" below center frequency. Frequency = Center frequency – nnnn*Channel spacing Value of nnnn is [0…number of channels/2] For conventional reasons, only 2 or 4 digit inputs are valid...
  • Page 44 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 RadioProperty SL%E? Get status of Error check and Full "0" Error check off CRC16 check modes "1" CRC8 Partial "2" CRC8 Full "3" CRC16 Full RadioProperty SL%E=x Set Error check and Full CRC16 check “OK"...

  • Page 45: Commands - Satelline-M3-Tr9/R9, Freewave

    SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 APPENDIX C 13.1 SL COMMANDS – SATELLINE-M3-TR9/R9, Freewave Receiver parts applies to SATELLINE-M3-R9 receiver module, forced permanently to Point to (can’t be changed) Multipoint Slave (RX Only) mode General format of the Freewave related SL...
  • Page 46 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Call Book Uint8 0 - A 0 - 9: Call Book SL~E=M1,I2,A<index> Entry To Entry Index <index> = [0-9,A] as presented on the left Call A: All Call Book Uint8, 0 - 9, 0 - 9: Call Book SL~E=M1,I3,A<index>,B<Address>,C<Address>,D<...
  • Page 47 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Hop Table Uint8 0 - 6 0: 902 - 928 MHz SL~E=M1,I6,A<Hop Table Version> Version 1: 915 - 928 MHz <Hop Table Version> = [0-6] as presented on the 2: 902 - 928 MHz, 16 left fewer freqs 3: 916 - 920 MHz...
  • Page 48 SATELLINE-M3-TR8 /-TR9 / -R9 Integration Guide, Version 2.2 Retry Odds Uint8 0 - 9 0 - 9: Defines a SL~E=M1,I18,A<Retry Odds> random base when <Retry Odds> = [0-9] slave is trying to resend data to master if Max Slave Retry count is reached.

  • Page 49: Version History

    Added a note to SATELLINE-M3-TR9 integrators, page 3. 21.09.2017 Inserted chapters 13.2 and 2.5 07.02.2018 Corrections for settings chapters 09.05.2019 Corrected the Configuration Manager download link 04.06.2019 Added frequency limits AU, NZ and BR 13.06.2019 Added Anatel, BR certification number 30.4.2021 SATELLINE-M3-R9 additions, multiple changes...

This manual is also suitable for:

Satelline-m3-tr8Satelline-m3-tr9

Table of Contents