Viking T Series Service Manual page 12

Operation
Lighting Grill (continued)
Place the lit match through the grid next to the flash
tube of the burner being lit. Keep your face as far
away from the grill as possible. Make sure the match
is adjacent to the flash tube. Push and turn the
control knob until the "HIGH" position on the knob
aligns with the indicator line on the control panel.
Make sure you are turning the control knob that
corresponds with the burner being lit. If the burner
does not light in 4 seconds, turn the knob to
"OFF," wait 5 minutes, and try again. If the
burner will not light after several attempts, see the
Troubleshooting section.
Lighting TruSear™ Infrared Burner (If Applicable)
Before lighting the burner, remove the stainless
steel cover. Push in and turn the TruSear™ infrared
control knob until the "HIGH" position on the knob
aligns with the indicator line on the control panel.
Press the electronic ignition button that corresponds
to the control knob. You will hear a clicking sound.
After the burner lights, hold in the control knob
about 5 seconds longer or until the burner remains
lit. Once lit, turn the control knob to the desired
setting. If the burner does not light within 4
seconds, release and turn the control knob to
"OFF." Wait 5 minutes for any accumulated gas
to dissipate and try again. After several failed
attempts the burner can be lit with a paper book
match using the flash tubes.
Lighting Side Burners
First, remove the burner cover or any cooking
utensil from the burner grate. Push and turn the
control knob until the "HIGH" position aligns with
the indicator line on the control panel. Immediately
press the electronic ignition button corresponding
to the burner(s) being lit until the burner is lit or until
4 seconds pass. If the burner does not light after
several attempts, wait five minutes to allow any
accumulated gas to dissipate. If the burner will not
light after several attempts, then the burner can be
lit by holding a lit match next to the burner ports.
Lighting Infrared Rotisserie Burner
The location of the infrared burner makes it more
susceptible to strong wind conditions—more so
than the protected grill burners. For this reason you
© 2009 Viking Preferred Service
should avoid using it during windy conditions.
Open the canopy. Push in and turn the rotisserie
control knob until the "HIGH" position on the
knob aligns with the indicator line on the control
panel and continue to hold in the knob. Press the
electronic ignition button which corresponds
to the rotisserie control knob. You will hear a
clicking sound. After the burner lights, hold the
rotisserie control knob in about 5 seconds longer
or until the burner remains lit. Once lit, turn the
control knob to the desired setting. If the burner
does not light within 4 seconds, release and turn
the control knob to "OFF". Wait 5 minutes for
any accumulated gas to dissipate. The Infrared
burner is Thermocouple activated. Using a match
near the burner may work if the spark module is
faulty or the battery is dead. If the burner does not
light after several attempts, then the burner can
be lit by holding a lit match to the burner (with the
control knob pushed in at the light position). Push
and turn the control knob until the "HIGH" position
on the knob aligns with the indicator line on the
control panel. Make sure you are turning the control
knob that corresponds with the burner being lit. If
relighting a hot burner, wait 5 minutes. Never leave
the rotisserie control knob at "ON" if
rotisserie is not in use.
Before You Begin
knob to "HIGH" and preheat racks for an
additional 15 — 20 minutes. This allows the
porcelain grates to be "seasoned."
"HIGH" and preheat for 5 — 7 minutes.
instructions.
desired doneness. Adjust heat setting, if
necessary. The control knob may be set to any
position between "HIGH" and "LOW."
should be cleaned after each use.)
12