Subscribe to Our Youtube Channel
Related Manuals for HIKOKI DS14DSDL
Summary of Contents for HIKOKI DS14DSDL
- Page 1 DS 14DSDL ∙ DS 18DSDL DV 14DSDL ∙ DV 18DSDL DS18DSDL DV18DSDL Handling instructions...
-
Page 2: General Power Tool Safety Warnings
power source and/or battery pack, picking up or GENERAL POWER TOOL SAFETY carrying the tool. WARNINGS Carrying power tools with your fi nger on the switch or energising power tools that have the switch on WARNING invites accidents. Read all safety warnings and all instructions. d) Remove any adjusting key or wrench before Failure to follow the warnings and instructions may result in turning the power tool on. -
Page 3: Additional Safety Warnings
Exposure to noise can cause hearing loss. tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to <DS14DSDL/DS18DSDL/DV14DSDL/DV18DSDL> normal when the battery warms up. 1. Use auxiliary handle(s), if supplied with the tool. 20. Install securely the hook. Unless the hook is securely Loss of control can cause personal injury. -
Page 4: Regarding Lithium-Ion Battery Transportation
The following show symbols used for the machine. TRANSPORTATION Be sure that you understand their meaning before use. When transporting a lithium-ion battery, please observe the DS14DSDL / DS18DSDL: following precautions. Cordless Driver Drill WARNING DV14DSDL / DV18DSDL: Notify the transporting company that a package contains a... -
Page 5: Standard Accessories
NOTE Wood Due to HiKOKI’s continuing program of research and development, the specifi cations herein are subject to Metal change without prior notice. Machine screw CHARGING Wood screw Before using the power tool, charge the battery as follows. Drill chuck capacity 1. - Page 6 Table 1-a Indications of the pilot lamp Lights for 0.5 seconds. Does not light for 0.5 Before Blinks (red) seconds. (off for 0.5 seconds) charging Lights continuously While charging Lights (red) Lights for 0.5 seconds. Does not light for 0.5 Charging Blinks (red) seconds.
-
Page 7: Mounting And Operation
(every second), please take the charger to the the cause of the failures. Once the charging has been HiKOKI Authorized Service Center. completed, give 15 minutes rest until the next charging. 4. Disconnect the charger’s power cord from the MOUNTING AND OPERATION receptacle or cigarette lighter socket. -
Page 8: Maintenance And Inspection
NOTE When replacing the carbon brush with a new one, be sure to use the HiKOKI Carbon Brush Code No. 999054. 5. Replacing carbon brushes (Fig. 14) Take out the carbon brush by fi rst removing the brush cap and then hooking the protrusion of the carbon brush with a fl... - Page 9 0 - 5250 0 - 6000 Bpm Hs /min ― ― 0 - 25500 0 - 27000 ― ― 1.5 - 13 1.5 - 13 1.5 - 13 1.5 - 13 DS14DSDL, DS18DSDL, DV14DSDL, DV18DSDL (NN) ― ― ― ―...
- Page 10 <UC18YML2> <UC18YFSL> <UC18YSL3>...
- Page 11 DV14DSDL DV18DSDL DS14DSDL DV14DSDL DS18DSDL DV18DSDL...
- Page 12 350 /min 1600 /min 400 /min 1700 /min 1800 /min 11.5mm...
- Page 14 14.4V (Li-ion) 337140 18V (Li-ion) 336471 UC18YML2 (14.4V - 18V) 336475 983006 331906 UC18YFSL (14.4V - 18V) 337131 999054 329897 UC18YSL3 (14.4V – 18V)
- Page 16 Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan Code No. C99700111 G Printed in China...
Need help?
Do you have a question about the DS14DSDL and is the answer not in the manual?
Questions and answers