Related Manuals for PhD Solutions MXC-P442-HDTL
Summary of Contents for PhD Solutions MXC-P442-HDTL
- Page 1 MXC-P442-HDTL CMSI-46PL 4 by 6 Matrix Operation Manual Operation Manual Operation Manual Operation Manual...
- Page 2 SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fi re, electrical shock and injury to persons.
-
Page 3: Table Of Contents
CONTENTS 1. Introduction ...............1 2. Applications ..............1 3. Package Contents ...........1 4. System Requirements ..........2 5. Features ..............2 6. Operation Controls and Functions ......3 6.1 Front Panel ............3 6.2 Rear Panel ............4 6.3 Side Panel ............5 6.4 Remote Control ...........5 6.5 IR Pin Assignment ..........6 6.6 RS-232 Protocols ..........6 6.7 RS-232 &... -
Page 4: Introduction
1. INTRODUCTION The 4 by 6 Matrix allows HDMI signal from any of its four sources to be routed to any of its six outputs simultaneously. With a thoughtful design for local and remote connections both required in system integration, the model is engineered with 2 HDMI and 4 CAT5e/6/7 outputs, the later ones carry major HDBaseT features including the transmission of high defi... -
Page 5: System Requirements
4. SYSTEM REQUIREMENTS • Input source equipment with HDMI connection cables • Industry CAT5e/6/7 cable • HDMI over CAT5e/6/7 Receivers with industrial CAT5e/6/7 cables • Output displays or audio receiver equipments with HDMI connection cables 5. FEATURES • Supports resolutions VGA to WUXGA and 480i to 1080p dependent upon the output display’s EDID settings •... -
Page 6: Operation Controls And Functions
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel POWER LOCK MENU 4X6 HDMI MATRIX LCM: This monitor displays your setting information with each input and output selection. IR: This IR window accepts the remote control signal of this device only. Power Button &... -
Page 7: Rear Panel
6.2 Rear Panel IR OUT IR IN IR OUT HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT IR IN IR OUT IR IN IR OUT IR IN IR OUT HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT IR IN HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V... -
Page 8: Side Panel
ALL IR IN: This slot is to connect with the IR Extender for IR signal receiving and send out to Receiver sides. Ensure that remote being used is within the direct line-of-sight of the IR Extender. DC24V: This slot is to plug the power cord with adaptor included in the package and then connect them with AC wall outlet for power supply. -
Page 9: Ir Pin Assignment
6.5 IR Pin Assignment IR Blaster Power IR Blaster Signal IR Extender IR Signal Power Grounding 6.6 RS-232 Protocols MXC-P442-HDTL CMSI-46PL Remote Control Console Assignment Assignment Baud Rate: 19200bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1... -
Page 10: Rs-232 & Telnet Commands
6.7 RS-232 & Telnet Commands Command Description A1~A4 Switch output A to 1~4 B1~B4 Switch output B to 1~4 C1~C4 Switch output C to 1~4 D1~D4 Switch output D to 1~4 E1~E4 Switch output E to 1~4 F1~F4 Switch output F to 1~4 A0~F0 Switch output A to F mute ABCD…1~ABCD…4... - Page 11 Command Description Setting EDID MODE. 1-STD 2-TV Display all the available commands UARTBAUD? Display each output's baud rate setting 1: 9600bps 2: 14400bps 3: 19200bps 4: 38400bps 5: 57600bps 6: 115200bps UARTBAUD2 Set output B’s baud rate from 1~6 UARTBAUD3 Set output C’s baud rate from 1~6 UARTBAUD5 Set output E’s baud rate from 1~6...
- Page 12 Note: 1. All the command will be not executed unless followed with a carriage return. All letters are case-insensitive. 2. Once switch RS-232 control to output Receiver all control can only be done under RS-232 system. 3. Output Receiver's RS-232 equipment baud rate must be set correctly in order to allow the Matrix to send through the commands.
-
Page 13: Rs-232 Uart Command Illustration Diagram
6.8 RS-232 UART Command Illustration Diagram UARTSW 0 Note: This command allows RS-232 to control IR OUT UARTSW 0 IR IN IR IN IR OUT HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT IR IN IR OUT IR OUT IR IN IR OUT HDMI OUT CAT5e/6/7 OUT CAT5e/6/7 OUT... -
Page 14: Telnet Control
6.9 Telnet Control Before attempting to use the telnet control, please ensure that both the Matrix (via the 'CONTROL' port) and the PC/Laptop are connected to the active networks. To access the telnet control in Windows 7, click on the 'Start' menu and type "cmd"... - Page 15 Type “IPCONFIG” To show all IP confi gurations. To reset the IP, type “RSTIP” and to use a set static IP, type ”SETIP” (For a full list of commands, see Section 6.7). Note: All the commands will be not executed unless followed by a carriage return.
-
Page 16: Web Gui Control
6.10 Web GUI Control On a PC/Laptop that is connected to the same active network as the Matrix, open a web browser (suggest using Internet Explorer Browser ver.9 and above) and type device's IP address on the web address entry bar. The browser will display the device's status, control and User setting pages. - Page 17 Clicking on the 'User Setting' tab allows you to reset the IP confi guration. The system will ask for a reboot of the device every time any of the settings are changed. The IP address needed to access the Web GUI control will also need to be changed accordingly on the web address entry bar.
-
Page 18: Connection Diagram
7. CONNECTION DIAGRAM ZONE ZONE ZONE ZONE ZONE ZONE IR1 Extender IR1 Extender IR1 Extender IR1 Extender HDMI Out HDMI Out HDMI Out HDMI Out RS232 Out IR2 Blaster RS232 Out IR2 Blaster RS232 Out IR2 Blaster RS232 Out IR2 Blaster RS-232 Device RS-232 Device RS-232 Device... -
Page 19: Specifications
8. SPECIFICATIONS Video Bandwidth 225MHz/6.75Gbps Input Ports 4 x HDMI, 5 x IR Extender, 1 x RS-232, 1 x LAN (Control only), 1 x RJ45 (Control Only), 1 x USB Mini-B (Service Only) Output Ports 2 x HDMI, 4 x CAT5e/6/7, 5 x IR Blaster Power Supply 24V / 3.75A DC (US/EU standards, CE/ FCC/UL certifi... -
Page 20: Acronyms
9. ACRONYMS ACRONYM COMPLETE TERM Digital Theater System EDID Extended Display Identifi cation Data HDCP High-bandwidth Digital Content Protection HDMI High-Defi nition multimedia Interface... - Page 21 PhD Solutions Product Warranty Should you feel your product does not function adequately due to defects in materials or workmanship, PhD Solutions (hereby referred to as “the warrantor”) will, for the length of the period indicated below: Repair the product with new or refurbished parts.
- Page 22 Return to Supplier When shipping the unit, carefully pack and send it prepaid (preferably in the original packaging) with a tracking number and adequate insurance. Please include a document or letter detailing the reason for return and include a daytime telephone number and/or email address where you can be contacted. If repair is required during the limited warranty period, the purchaser will be required to provide a sales receipt or other proof of purchase, indicating date and location of purchase as well as the price paid for the product.
- Page 23 Premium High Definition Solutions Home page: http://www.phdsolutions.co...