Page 1
This Service Manual describes replacement parts for the green products. When repairing these green product(s), use the part(s) described in this manual and lead-free solder (*2). For (*1) and (*2), see the next page. TOSHIBA CORPORATION 2007 Published in Japan, July 2007 GREEN...
Page 2
Hazardous Substances. From July 1, 2006, the RoHS Directive will prohibit any marketing of new products containing the restricted substances. Increasing attention is given to issues related to the global environmental. Toshiba Corporation recognizes environmental protection as a key management tasks, and is doing its utmost to enhance and improve the quality and scope of its environmental activities.
All manuals and user guides at all-guides.com MAIN SECTION HDD & DVD / Video Cassette Recorder RD-XV47KE/RD-XV47KB/RD-XV47KF Main Section I Specifications I Preparation for Servicing I Adjustment Procedures I Schematic Diagrams I BOARD’s I Exploded Views I Parts List TABLE OF CONTENTS Specifications .
435 x 99.5 x 380 mm Operating temperature 5°C to 40°C Operating humidity Less than 80% (no condensation) TV format AL / SECAM - BG / DK (RD-XV47KE) PAL-I (RD-XV47KB) SECAM LL, PAL B / G (RD-XV47KF) Recording Recording format Video Recording format (DVD-RW only),...
All manuals and user guides at all-guides.com LASER BEAM SAFETY PRECAUTIONS This DVD player uses a pickup that emits a laser beam. Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin.
All manuals and user guides at all-guides.com IMPORTANT SAFETY PRECAUTIONS Product Safety Notice K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the Some electrical and mechanical parts have special AC outlet. safety-related characteristics which are often not evi- dent from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage,...
Page 7
All manuals and user guides at all-guides.com Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, Chassis or Secondary Conductor parts, and wires have been returned to their original positions. Afterwards, do the following tests and con- Primary Circuit firm the specified values to verify compliance with safety standards.
All manuals and user guides at all-guides.com STANDARD NOTES FOR SERVICING NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Circuit Board Indications Pb (Lead) Free Solder 1. The output pin of the 3 pin Regulator ICs is When soldering, be sure to use the Pb free solder. indicated as shown.
Page 9
All manuals and user guides at all-guides.com 3. The flat pack-IC on the BOARD is affixed with With Soldering Iron: glue, so be careful not to break or damage the foil 1. Using desoldering braid, remove the solder from of each pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 10
All manuals and user guides at all-guides.com 2. Installation With Iron Wire: 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the flux which is applied to all pins of the flat pack-IC, BOARD so you can install a replacement flat pack- you can remove it easily.
Page 11
All manuals and user guides at all-guides.com Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
All manuals and user guides at all-guides.com HANDLING PRECAUTIONS FOR HDD CAUTION: 4. OTHERS a. Be careful so as not to do the followings. 1. SHOCK Otherwise, HDD might be damaged. a. Exposing HDD to shock may be the biggest - DO NOT disassemble HDD.
All manuals and user guides at all-guides.com PREPARATION FOR SERVICING How to Enter the Service Mode About Optical Sensors Caution: An optical sensor system is used for the Tape Start and End Sensors on this equipment. Carefully read and follow the instructions below. Otherwise the unit may operate erratically.
All manuals and user guides at all-guides.com CABINET DISASSEMBLY INSTRUCTIONS NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1. Disassembly Flowchart REMOVAL This flowchart indicates the disassembly steps to gain REMOVE/*UNHOOK/ LOC. PART Fig. access to item(s) to be serviced. When reassembling, UNLOCK/RELEASE/ Note follow the steps in reverse order.
Page 15
All manuals and user guides at all-guides.com Reference Notes 1. Locking Tabs (L-1) and (L-2) are fragile. Be careful (S-3B) not to break them. [3] Front Bracket 1-1. Remove Screw (S-2). (S-3B) 1-2. Release five Locking Tabs (L-1). (S-3) Front 1-3.
Page 16
All manuals and user guides at all-guides.com CN3002 [14] BOARD SWITCH CN3001 (S-7) Desolder [9] BOARD ATA [15] BOARD FRONT JACK (S-14) (S-12) [7] HDD Unit CL1001 (S-7) (S-13) HDD Rubber CN3001 [8] HDD Support [13] BOARD POWER HDD Rubber SUPPLY (S-8) (S-8)
Page 17
All manuals and user guides at all-guides.com Cylinder Assembly FE Head ACE Head Assembly SW507 LD-SW [17] Deck Assembly [18] BOARD [19] BOARD [18] BOARD POWER POWER SWITCH [17] Deck Assembly Cam Gear Hole (S-18) Shaft [18] BOARD POWER Desolder Hole (S-19) LD-SW...
Page 18
All manuals and user guides at all-guides.com (S-20) [20] Deck Pedestal (S-20) [21] Front Bracket R [22] Bracket R (S-22) (S-21) Fig. D9 3. How to Eject Manually Note: When rotating the gear, be careful not to damage the gear. 1.
All manuals and user guides at all-guides.com ELECTRICAL ADJUSTMENT INSTRUCTIONS NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. NOTE: 1.Electrical adjustments are required after replacing circuit components and certain mechanical parts. It is important to do these adjustments only after Figure 1 all repairs and replacements have been com- pleted.
All manuals and user guides at all-guides.com HOW TO SELF-CHECK AND INITIALIZE THE HDD & DVD/VCR 1. Turn on the HDD & DVD/VCR. 2. To put the HDD & DVD/VCR into the HDD mode, press [HDD] on the remote control unit. 3.
Page 21
All manuals and user guides at all-guides.com Table 2: Indication of DVD self-check (*7) INDICATION DESCRIPTION Connection of DVD is normal. NOT FOUND DVD drive cannot be found. FFC cable (connecting to CN401) between the DVD drive and the DVD/HDD MAIN BOARD CABLE ERROR is not connected correctly.
All manuals and user guides at all-guides.com FIRMWARE RENEWAL MODE 1. Update Contents 4. Load the update disc. The TV screen will display Fig. c. Item Status - If the update disc contains only a single file, the update will initiate automatically when the disc is Update B/E FIRMWARE inserted.
Page 23
All manuals and user guides at all-guides.com The status displayed in *2 is as shown below. 3. How to Verify the Firmware Version Display Status 1. Turn the power on and remove the disc in the tray. Loading F/W from Update Disc or EXECUTING writing to Flash memory 2.
All manuals and user guides at all-guides.com TROUBLESHOOTING NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1 Power Supply Section FLOW CHART NO.1 The power cannot be turned on. See FLOW CHART No.2 <The fuse blows out.> Is the fuse normal? Is normal state restored when once unplugged Check for lead or short-circuiting of primary power cord is plugged again after several seconds.
Page 25
All manuals and user guides at all-guides.com FLOW CHART NO.6 AL+44V is not outputted. Check D013, D1104, C013, and their periphery, Is 44V voltage supplied to the emitter of Q1511? and service it if defective. Is the "L" pulse (approximately 0V) inputted to Is the "H"...
Page 26
All manuals and user guides at all-guides.com FLOW CHART NO.11 HDD+5V is not outputted. Is 5V voltage supplied to the emitter of Q1102? Check D016, D1032, D1102, C1104, C1105 and their periphery, and service it if defective. Is the "L" pulse outputted to the collector of Q1104? Check Q1104, D1117 and their periphery, and service it if defective.
Page 27
All manuals and user guides at all-guides.com 2 HDD/DVD Section FLOW CHART NO.1 The key operation is not functioning. Are the contact point and the installation state of Re-install the key switches correctly or replace the key switches normal? the poor switch. Is the control voltage normally inputted into Check the key switches and their periphery, and service it if defective.
Page 28
All manuals and user guides at all-guides.com FLOW CHART NO.4 VIDEO E-E does not appear normally. Are the video signals inputted to each pin of Check the line between video input terminal and IC1509? each pin of IC1509. → JK1504 IC1509 16PIN VIDEO-IN 1 (AV1)
Page 29
All manuals and user guides at all-guides.com Replace the DVD MECHANISM & DVD MAIN Are the video signals outputted to each pin of BOARD ASSEMBLY. CN1502? CN1502 24PIN VIDEO-Y(I/P)-OUT CN1502 30PIN VIDEO-Y(I)-OUT CN1502 26PIN VIDEO-Pr/Cr-OUT CN1502 28PIN VIDEO-Pb/Cb-OUT CN1502 22PIN VIDEO-C-OUT Are the video signals shown above inputted into Check the line between each pin of CN1502 and...
Page 30
All manuals and user guides at all-guides.com FLOW CHART NO.5 Picture does not appear normally. Set the disc on the disc tray, and playback it. (DVD MODE) Or, playback by selecting the picture in HDD top menu. (HDD MODE) Replace the DVD MECHANISM & DVD MAIN Are the video signals outputted to each pin of BOARD ASSEMBLY.
Page 31
All manuals and user guides at all-guides.com FLOW CHART NO.6 Check the line between audio input terminal and Audio E-E does not appear normally. each pin of IC1509, and service it if defective. No (Rear →JK1504 IC1509 93,94PIN AUDIO-IN1 (AV1) or Front →JK3002, IC1509...
Page 32
All manuals and user guides at all-guides.com Replace the DVD MECHANISM & DVD MAIN Are the analog audio signals outputted to each pin BOARD ASSEMBLY. of CN1502? CN1502 14PIN AUDIO (L)-OUT CN1502 16PIN AUDIO (R)-OUT Check each line between each pin of CN1502 Are the analog audio signals inputted to each pin and each pin of IC1508, and service it if defective.
Page 33
All manuals and user guides at all-guides.com FLOW CHART NO.7 Audio is not outputted during playback. Set the disc on the disc tray, and playback it. (DVD MODE) Or, playback by selecting the picture in HDD top menu. (HDD MODE) Replace the DVD MECHANISM &...
Page 34
All manuals and user guides at all-guides.com 3 VCR Section FLOW CHART NO.1 The key operation is not functioning. Are the contact point and the installation state of Re-install some key switches correctly or the key switches normal? replace some key switches. Check the key switches and their periphery, and Is the control voltage normally inputted into service it if defective.
Page 35
All manuals and user guides at all-guides.com FLOW CHART NO.3 Cassette tape can not be loaded. When loading a cassette tape, on Pin(10) of Check the line between the start sensor and IC501, does the "L" pulse switch to the "H" pulse? Pin(10) of IC501, and service it if defective.
Page 36
All manuals and user guides at all-guides.com FLOW CHART NO.6 Capstan Motor does not rotate. Is 5V voltage supplied to Pin(2) of CN502? Check the P-ON+5V line and service it if defective. Is over approximately 2.6V voltage supplied to Check the line between Pin(5) of CN502 and Pin(5) of CN502? Pin(76) of IC501, and service it if defective.
Page 37
All manuals and user guides at all-guides.com FLOW CHART NO.10 Video E-E does not appear normally. Are the video signals inputted to each pin of Check the line between video input terminal and IC1509? each pin of IC1509. → JK1504 IC1509 16PIN VIDEO-IN 1 (AV1)
Page 38
All manuals and user guides at all-guides.com FLOW CHART NO.11 Check the line between audio input terminal and Hi-Fi E-E audio does not operate normally. each pin of IC1509, and service it if defective. No (Rear or Front →JK1504 IC1509 93,94PIN AUDIO-IN1 (AV1) input)
Page 39
All manuals and user guides at all-guides.com FLOW CHART NO.12 Hi-Fi audio can not be recorded normally. (E-E mode is normal.) Is the Hi-Fi-COM signal outputted to Pin(26) of Replace IC451. IC451? Check the line between Pin(8) of CN251 and Is the line between Pin(8) of CN251 and Pin(26) of IC451 normal? Pin(26) of IC451, and service it if defective.
Page 40
All manuals and user guides at all-guides.com FLOW CHART NO.15 Hi-Fi audio can not be playbacked normally in the linear audio mode. (E-E mode is normal.) Is the audio signal outputted to Pin(11) of IC301? Is the audio signal supplied to Pin(5) of IC301? Check the line between Pin(11) of Replace IC301 and Pin(80) of IC451, and...
All manuals and user guides at all-guides.com FUNCTION INDICATOR SYMBOLS < VCR Section > When the power comes on again after that by pressing [ ] button, an error message is displayed on the TV screen as follows. When reel or capstan mechanism is not functioning P-ON+5V Power safety detection correctly 0:00:00...
SW507 IC501 Models & Marks (SERVO/SYSTEM CONTROL) LD-SW BOARD POWER ACE HEAD ASSEMBLY CN504 AL+5V(2) LD-SW Model Mark CONTROL CTL(+) CTL(+) RD-XV47KE HEAD CTL(-) CTL(-) KEY- 1 KEY SWITCH RD-XV47KB ST-S REC-SAF-SW 31 AL+5V(2) RD-XV47KF END-S SW506 TP502 T-REEL REC-SAFETY...
Page 43
All manuals and user guides at all-guides.com Sub System Control Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. IC1501 (SUB MICRO CONTROLLER) REG-CONT IC1502 REG-CONT PWR -SW Q1527 TO SUB PW-SW RESET LOW-POW RESET TIMER+5V POWER SUPPLY LOW-POW FAN-LOCK BLOCK DIAGRAM FAN-LOCK FAN-CONT1 FAN-CONT1...
Page 44
All manuals and user guides at all-guides.com Digital Signal Process Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. REC VIDEO SIGNAL PB VIDEO SIGNAL REC AUDIO SIGNAL PB AUDIO SIGNAL CN3001 CN3002 CN901 HARD DISK DRIVE IC201 IC101 BOARD ATA ERROR AMP DVD MECHANISM CN201...
Page 45
All manuals and user guides at all-guides.com Video Selector Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. REC VIDEO SIGNAL PB VIDEO SIGNAL IC1509 (VIDEO SELECTOR) BOARD BOARD REAR JACK POWER Q2001 JK2001 CN2001 CN1506 VIDEO OUT2 BUFFER VIDEO-OUT2 DRIVER VIDEO-G VIDEO-G-IN JK2001...
Page 46
All manuals and user guides at all-guides.com Video Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. REC-VIDEO SIGNAL PB-VIDEO SIGNAL MODE: SP/REC Comparison Chart of Models & Marks Model Mark RD-XV47KE IC501 (OSD) RD-XV47KB IIC-BUS SCL TO SERVO/SYSTEM RD-XV47KF CHARACTER CONTROL BLOCK IIC-BUS SDA COLOR...
Page 47
All manuals and user guides at all-guides.com Audio Selector Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. REC AUDIO SIGNAL PB AUDIO SIGNAL BOARD REAR JACK IC1509(AUDIO SELECTOR) JK2001 BOARD POWER CN1506 CN2001 AUDIO(L)-IN2 AUDIO(L)-IN2 TO SUB SYSTEM AUDIO(R)-IN2 AUDIO(R)-IN2 CONTROL AUDIO(L)-OUT2 AUDIO(L)-OUT2...
Page 48
All manuals and user guides at all-guides.com Audio Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. PB-AUDIO SIGNAL REC-AUDIO SIGNAL Mode : SP/REC BOARD POWER N-A-PB TO Hi-Fi AUDIO N-A-REC BLOCK DIGRAM IC301 (AUDIO SIGNAL PROCESS) PB-ON LINE MUTE (DECK ASSEMBLY) SP/LP-ON P-ON+5V ACE HEAD ASSEMBLY...
Page 49
All manuals and user guides at all-guides.com Hi-Fi Audio Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. PB-AUDIO SIGNAL REC-AUDIO SIGNAL Mode : SP/REC BOARD POWER VCR-AUDIO-IN(L) TO AUDIO VCR-AUDIO-IN(R) SELECTOR BLOCK DIAGRAM IC451 ( Hi-Fi AUDIO PROCESS) R-CH IIC-BUS SDA COMP SERIAL NOISE...
Page 50
All manuals and user guides at all-guides.com Power Supply Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. CAUTION ! CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. For continued protection against fire hazard, The voltage for parts in hot circuit is measured using If Main Fuse (F1001) is blown , check to see that all components in the power supply replace only with the same type fuse.
Page 51
All manuals and user guides at all-guides.com Sub Power Supply Block Diagram NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. CN1503 1 AL-30V J902 2 AL+44V AL+44V Q1511 3,4 AL+16.3V P-ON+15V 7,8 AL+12V 14 P-ON+9V Q1512 15,16 P-ON+5V 17,18 AL+5V(3) Q1508 22 AL+5V POWER SUPPLY AL+16V/+12V BLOCK DIAGRAM...
All manuals and user guides at all-guides.com SCHEMATIC DIAGRAMS / BOARD’S AND TEST POINTS NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 53
All manuals and user guides at all-guides.com LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE. 2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F1001) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply.
Page 54
All manuals and user guides at all-guides.com POWER 1/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Comparison Chart of Models and Marks MODEL MARK RD-XV47KE RD-XV47KB RD-XV47KF 1-14-3 E3B90SCP1...
Page 55
All manuals and user guides at all-guides.com POWER 2/10 & SENSOR Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. FL601 MATRIX CHART G7(GR7) G6(GR6) G5(GR5) G4(GR4) G3(GR3) G2(GR2) G1(GR1) (SG1) (SG2) (SG3) (S3) (SG4) (SG5) (S2) (SG6) (SG7) (S1)
Page 56
All manuals and user guides at all-guides.com POWER 3/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Comparison Chart of Models and Marks MODEL MARK RD-XV47KE RD-XV47KB RD-XV47KF 1-14-5 E3B90SCP3...
Page 57
All manuals and user guides at all-guides.com POWER 4/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-6 E3B90SCP4...
Page 58
You can choose either Group. The difference between Group A and Group B is shown below. Group A Group B IC1502A R3112N211A-TR-F ---------- IC1502B ---------- PST3621NR C1505A 0.015 ---------- C1505B ---------- 0.15 Comparison Chart of Models and Marks MODEL MARK RD-XV47KE RD-XV47KB RD-XV47KF 1-14-7 E3B90SCP5...
Page 59
All manuals and user guides at all-guides.com POWER 6/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-8 E3B90SCP6...
Page 60
All manuals and user guides at all-guides.com POWER 7/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-9 E3B90SCP7...
Page 61
All manuals and user guides at all-guides.com POWER 8/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-10 E3B90SCP8...
Page 62
All manuals and user guides at all-guides.com POWER 9/10 Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-11 E3B90SCP9...
Page 63
All manuals and user guides at all-guides.com POWER 10/10 Schematic Diagram ( C ) < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Comparison Chart of Models and Marks MODEL MARK RD-XV47KE RD-XV47KB RD-XV47KF 1-14-12 E3B92SCP10...
Page 64
All manuals and user guides at all-guides.com POWER SUPPLY Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. CAUTION ! CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. For continued protection against fire hazard, The voltage for parts in hot circuit is measured using If Main Fuse (F1001) is blown , check to see that all components in the power supply...
Page 65
All manuals and user guides at all-guides.com FRONT JACK & SWITCH Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-14 E3B90SCFJ...
Page 66
All manuals and user guides at all-guides.com REAR JACK Schematic Diagram < VCR Section > ATA Schematic Diagram < DVD/HDD Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. E3B90SCRJ E3B90SCAT 1-14-15...
Page 67
All manuals and user guides at all-guides.com AFV Schematic Diagram < VCR Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Comparison Chart of Models and Marks MODEL MARK RD-XV47KE RD-XV47KB RD-XV47KF 1-14-16 E3B90SCAFV...
Page 68
All manuals and user guides at all-guides.com DVD/HDD MAIN 1/5 Schematic Diagram < DVD/HDD Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 2 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD/HDD Main Schematic Diagram Section. 1-14-17 E3B90SCD1...
Page 69
All manuals and user guides at all-guides.com DVD/HDD MAIN 2/5 Schematic Diagram < DVD/HDD Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 2 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD/HDD Main Schematic Diagram Section. 1-14-18 E3B90SCD2...
Page 70
All manuals and user guides at all-guides.com DVD/HDD MAIN 3/5 Schematic Diagram < DVD/HDD Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 2 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD/HDD Main Schematic Diagram Section. 1-14-19 E3B90SCD3...
Page 71
All manuals and user guides at all-guides.com DVD/HDD MAIN 4/5 Schematic Diagram < DVD/HDD Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 2 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD/HDD Main Schematic Diagram Section. 1-14-20 E3B90SCD4...
Page 72
All manuals and user guides at all-guides.com DVD/HDD MAIN 5/5 Schematic Diagram < DVD/HDD Section > NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 2 NOTE: The order of pins shown in this diagram is different from that of actual IC101. IC101 is divided into five and shown as IC101 (1/5) ~ IC101 (5/5) in this DVD/HDD Main Schematic Diagram Section. 1-14-21 E3B90SCD5...
Page 73
All manuals and user guides at all-guides.com BOARD POWER Top View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. BOARD SENSOR View TO BOARD SENSOR (END-SENSOR) TP503 TP504 VR501 SW-POINT RF-SW BHF300F01012A TP301 C-PB BHF300F01012B J308 AV1-V-OUT TO BOARD SENSOR (START-SENSOR) 1-14-22 BE3B00F01011A...
Page 74
All manuals and user guides at all-guides.com BOARD POWER Bottom View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. PIN 56 OF IC301 PIN 30 OF IC1509 PIN 28 OF CN1502 PIN 26 OF CN1502 PIN 24 OF CN1502 PIN 22 OF CN1502 PIN 14 OF CN1502...
Page 75
All manuals and user guides at all-guides.com BOARD POWER SUPPLY Top View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. CAUTION ! Because a hot chassis ground is present in the power CAUTION ! supply circut, an isolation transformer must be used. For continued protection against fire hazard, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
Page 76
All manuals and user guides at all-guides.com BOARD POWER SUPPLY Bottom View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. Because a hot chassis ground is present in the power CAUTION ! CAUTION ! supply circut, an isolation transformer must be used. For continued protection against fire hazard, Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit.
Page 77
All manuals and user guides at all-guides.com BOARD FRONT JACK Top View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. BOARD SWITCH BOARD SWITCH Top View Bottom View BOARD FRONT JACK Bottom View BE3B00F01021B BE3B00F01021C 1-14-26...
Page 78
All manuals and user guides at all-guides.com BOARD REAR JACK Top View BOARD REAR JACK Bottom View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. BE3B00F01021D BOARD POWER SWITCH BOARD POWER SWITCH BOARD ATA Top View BOARD ATA Bottom View Top View Bottom View BE3B00F01011B BE4340F01032...
Page 79
All manuals and user guides at all-guides.com BOARD AFV Top View BOARD AFV Bottom View NOTE: BOARD MEANS PRINTED CIRCUIT BOARD. 1-14-28 BE6800F01091...
All manuals and user guides at all-guides.com WAVEFORMS NOTE: Input: COLOR BAR SIGNAL (WITH 1KHz AUDIO SIGNAL) Pin 56 of IC301 Pin 22 of CN1502 Pin 14 of CN1502 V-OUT E-E 0.2V 20μs VIDEO-C 0.2V 20μs AUDIO(L)-OUT 0.5ms Pin 56 of IC301 UPPER Pin 30 of IC1509 Pin 28 of CN1503...
Signal Mark Function Name Comparison Chart of Models and Marks Not Used Model Mark Not Used RD-XV47KE Not Used RD-XV47KB Recording Safety SW RD-XV47KF REC-SAF- Detect (With Record IC501 ( SERVO / SYSTEM CONTROL ) tab=”L”/ With out Record tab=”H”)
Page 84
All manuals and user guides at all-guides.com Signal Signal Mark Function Mark Function Name Name Capstan Motor Rotation OUT C-POW-SW Capstan Power IN C-FG Detection Pulse Switching Signal AMPVss Ground Not Used IN SECAM-H SECAM Mode at High Not Used Drum Motor Phase/ Not Used IN D-PFG...
Page 85
All manuals and user guides at all-guides.com IC612 ( VFD DRIVER ) Signal Function Name IN CLK Clock Input IN STB Serial Interface Strobe Not Used Not Used Ground Power Supply OUT SG1 OUT SG2 OUT SG3 10 OUT SG4 Segment Output 11 OUT SG5 12 OUT SG6...
All manuals and user guides at all-guides.com LEAD IDENTIFICATIONS KRA103M-AT/P 2SC2120-(Y)(TE2 F T) KTC2026-Y/P 2SK3798(Q) KRA104M-AT/P KTA-1266-GR-AT/P KRC103M-AT/P KTC3203-Y-AT/P KRC106M-AT/P KTC3198-Y-AT/P KTA1267Y-AT/P KTC3266-GR-AT/P KTA1281Y-AT/P KTC3199-(BL,Y)-AT/P B C E G D S E C B E C B PT204-6B-12 KIA431-AT/P PQ070XF01SZH KIA4558P/P TLV1117I TO-220 UTC4580...
All manuals and user guides at all-guides.com EXPLODED VIEWS Cabinet L-12 A,B,C,D,E See Electrical Parts List for parts with this mark. B-24 D,E,F ( P3-3 ) BOARD REAR JACK B-10 ( P5 ) TU1501 BOARD AFV ( P4 ) JW2001 B-15 BOARD SENSOR ( P6 )
Page 88
All manuals and user guides at all-guides.com (P1) POWER ASSEMBLY (P4) BOARD SENSOR ( P5 ) BOARD AFV B-10 TU1501 ( P4 ) BOARD SENSOR BOARD POWER B-31 B-16 ( P1 ) POWER ASSEMBLY BOARD POWER SWITCH (P5) BOARD AFV ( P5 ) BOARD AFV 1-19-2...
Page 89
All manuals and user guides at all-guides.com (P2) DVD MECHANISM & DVD/HDD MAIN BOARD ASSEMBLY ( P2 ) DVD MECHANISM & DVD/HDD MAIN BOARD ASSEMBLY (P3) BOARD PW/SW Note : Refer to the Parts List for P3, BOARD PW/SW B-24 A,B,C JW2001 ( P3-3 )
Page 90
All manuals and user guides at all-guides.com Packing [RD-XV47KE/RD-XV47KF] Lower Side Upper Side X-2D X-2C X-2B X-2A Comparison Chart of Models and Marks Model Mark RD-XV47KE RD-XV47KF 1-19-4 E3B90PEX...
Page 91
All manuals and user guides at all-guides.com Packing [RD-XV47KB] Lower Side Upper Side X-30 X-29 1-19-5 E3B90PEX...
All manuals and user guides at all-guides.com MECHANICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Loca- Mark TSB P/N Reference No. Description ! have special characteristics important to safety. tion No. Before replacing any of these components, read L-1A GBHC3050 SCREW TAP TIGHT M3X5...
Page 93
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. L-9Q 0VM412937A SCREW C-TIGHT M3X6 P000484000 1VMN23453 QUICK GUIDE E3B91BD E5610UD P000484110 1VMN23456 QUICK GUIDE E3B92FD L-9R 0VM412937A SCREW C-TIGHT M3X6...
All manuals and user guides at all-guides.com ELECTRICAL PARTS LIST PRODUCT SAFETY NOTE: Products marked with a Loca- Mark TSB P/N Reference No. Description ! have special characteristics important to safety. tion No. Before replacing any of these components, read C254 CE1JMAVSL1R0 ELECTROLYTIC CAP .
Page 95
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. C346 CHD1JZ30F104 CHIP CERAMIC C453 CE1AMAVSL220 ELECTROLYTIC CAP . CAP .(1608) F Z 0.1μF/50V 22μF/10V M H7 C347 CHD1EK30B104 CHIP CERAMIC C454...
Page 96
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. C509 CHD1JK30B102 CHIP CERAMIC C612 CHD1JK30B472 CHIP CERAMIC CAP .(1608) B K 1000pF/ CAP .(1608) B K 4700pF/ C510 CHD1JK30B472 CHIP CERAMIC...
Page 97
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. C1542 CHD1JZ30F104 CHIP CERAMIC C1589 CE1JMASDLR47 ELECTROLYTIC CAP . CAP .(1608) F Z 0.1μF/50V 0.47μF/50V M C1544 CHD1JZ30F104 CHIP CERAMIC...
Page 98
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. C1629 CHD1JZ30F104 CHIP CERAMIC C1678 CHD1JZ30F104 CHIP CERAMIC CAP .(1608) F Z 0.1μF/50V CAP .(1608) F Z 0.1μF/50V C1630 CHD1JZ30F104 CHIP CERAMIC...
Page 99
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. D1527 QDTZ001SS133 SWITCHING DIODE If IC1502B is PST3621NR, then C1505B is 0.15μF. 1SS133(T-77) IC1502B P000483900 QSZBA0TMM162 SYSTEM RESET IC D1528 QDTB0MTZJ5R6 ZENER DIODE MTZJT- PST3621NR...
Page 100
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. Q406 NQ1YKTC3875S CHIP TRANSISTOR Q1542 NQSYKTC3199P TRANSISTOR KTC3199-Y- KTC3875S-Y-RTK/P AT/P Q451 NQ1ZKRC103SP TRANSISTOR KRC103S- Q1543 NQSYKTC3199P TRANSISTOR KTC3199-Y- RTK/P AT/P...
Page 101
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. CHIP RES. 1/10W J 470 Ω CHIP RES. 1/10W J 1k Ω R463 RRXAJR5Z0471 R623 RRXAJR5Z0102 CHIP RES.
Page 102
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. CHIP RES. 1/10W J 3.3k Ω R1585 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 R1645 RRXAJR5Z0332 Ω CHIP RES.
Page 103
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. R1711 RRXAZR5Z0000 CHIP RES.(1608) 1/10W 0 R1771 RCX6JATZ0123 CARBON RES. 1/6W J 12k Ω Ω CHIP RES.
Page 104
All manuals and user guides at all-guides.com BOARD POWER SUPPLY Loca- Mark TSB P/N Reference No. Description tion No. Loca- VR501 VRCB104HH014 CARBON P .O.T. VZ067TL1 Mark TSB P/N Reference No. Description tion No. B104 PB(F) ! P3-4 P000483760 1VSA15686-4 BOARD POWER SUPPLY X301 P000468200 FXC445LLN004...
Page 105
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. C1132 CE0KMASDL102 ELECTROLYTIC CAP . D1115 QDTZ001SS133 SWITCHING DIODE 1000μF/6.3V M 1SS133(T-77) C1133 CA2A102DT018 POLYESTER FILM CAP . D1116 QDTZ001SS133 SWITCHING DIODE...
Page 106
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. L1001-2 XL03010XM001 BEAD CORE B16 RH R1029 RCX4JATZ0184 CARBON RES. 1/4W J 180k Ω 3.5X10X1.3 R1033 RCX4JATZ0560 CARBON RES.
Page 107
All manuals and user guides at all-guides.com BOARD FRONT JACK Loca- Mark TSB P/N Reference No. Description tion No. Loca- R1149 RCX4JATZ0682 CARBON RES. 1/4W J Mark TSB P/N Reference No. Description tion No. 6.8k Ω P3-2 P000483740 1VSA15686-2 BOARD FRONT JACK R1150 RCX4JATZ0682 CARBON RES.
Page 108
All manuals and user guides at all-guides.com Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. SW3004 P000483300 SST0101AL041 TACT SWITCH C2009 CE1JMASDL1R0 ELECTROLYTIC CAP . 1μF/ SKQSAF001A 50V M SW3005 P000483300 SST0101AL041 TACT SWITCH C2010...
Page 109
All manuals and user guides at all-guides.com BOARD AFV BOARD ATA Loca- Loca- Mark TSB P/N Reference No. Description Mark TSB P/N Reference No. Description tion No. tion No. P000483720 1VSA15656 BOARD AFV P000472730 1VSA13582 BOARD ATA Consists of the following: P000484120 1VSA15657 BOARD AFV CONNECTORS...
Page 110
All manuals and user guides at all-guides.com DECK MECHANISM SECTION HDD & DVD / Video Cassette Recorder RD-XV47KE/RD-XV47KB/RD-XV47KF Deck Mechanism Section I Standard Maintenance I Mechanism Alignment Procedures I Disassembly / Assembly of Mechanism I Deck Exploded Views I Deck Parts List TABLE OF CONTENTS Standard Maintenance .
All manuals and user guides at all-guides.com STANDARD MAINTENANCE Service Schedule of Components This maintenance chart shows you the standard of replacement and cleaning time for each part. Because those may replace depending on environment and purpose for use, use the chart for reference. I: Replace h: Hours : Cleaning...
Page 112
All manuals and user guides at all-guides.com Cleaning of ACE Head Cleaning Clean the head with a cotton swab. Cleaning of Video Head Procedure Clean the head with a head cleaning stick or chamois 1.Remove the top cabinet. cloth. 2.Dip the cotton swab in 90% ethyl alcohol and clean Procedure the ACE Head.
All manuals and user guides at all-guides.com SERVICE FIXTURE AND TOOLS J-1-1, J-1-2 Ref. No. Name Part No. Adjustment J-1-1 Alignment Tape FL6A Head Adjustment of ACE Head J-1-2 Alignment Tape FL6N8 Azimuth and X Value Adjustment of ACE Head / (2 Head model) Adjustment of Envelope Waveform FL6NS8...
All manuals and user guides at all-guides.com MECHANICAL ALIGNMENT PROCEDURES Explanation of alignment for the tape to correctly run B. Method to place the Cassette Holder in the tape- starts on the next page. Refer to the information below loaded position without a cassette tape on this page if a tape gets stuck, for example, in the 1.
Page 115
All manuals and user guides at all-guides.com 1. Tape Interchangeability Alignment Note: To do these alignment procedures, make sure that the Tracking Control Circuit is set to the preset position every time a tape is loaded or unloaded. (Refer to page 2-3-4, procedure 1-C, step 2.) Equipment required: Dual Trace Oscilloscope...
Page 116
All manuals and user guides at all-guides.com 1-A. Preliminary/Final Checking and 4. If creasing or snaking is apparent, adjust the Tilt Alignment of Tape Path Adj. Screw of the ACE Head. (Fig. M6) Purpose: To make sure that the tape path is well stabilized. Azimuth Adj.
Page 117
All manuals and user guides at all-guides.com 5. When Guide Rollers [2] and [3] (Refer to Fig. M3) 5. To shift the CTL waveform, press [PROGRAM are aligned properly, there is no envelope drop or [PROGRAM ] button. Then make sure that either at the beginning or end of track as shown in the maximum output position of PB FM envelope Fig.
Page 118
All manuals and user guides at all-guides.com 1-D. Azimuth Alignment of Audio/Con- 2. When the tape has been curled up or bent, turn the trol/ Erase Head alignment screw to adjust the height of REV Post. (Refer to Fig. M11 and M13.) Purpose: To correct the Azimuth alignment so that the Audio/ Control/Erase Head meets tape tracks properly.
All manuals and user guides at all-guides.com DISASSEMBLY/ASSEMBLY PROCEDURES OF DECK MECHANISM Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to CABINET DISASSEMBLY INSTRUCTIONS.) All the following procedures, including those for adjustment and replacement of parts, should be done in Eject mode;...
Page 120
All manuals and user guides at all-guides.com REMOVAL INSTALLATION STEP START- REMOVE/*UNHOOK/ /LOC. PART ADJUSTMENT Fig. No. UNLOCK/RELEASE/ CONDITION UNPLUG/DESOLDER Loading Arm (SP) (+)Refer to Alignment [34] [26] DM2H, DM14H Assembly Sec.Page 2-5-1 Loading Arm (TU) (+)Refer to Alignment [35] [34] DM2H, DM14H Assembly...
Page 121
All manuals and user guides at all-guides.com Top View [44] [45] [49] [46] [14] [13] [11] [15] [38] [10] [12] [37] [36] [43] [32] [41] [31] [40] [42] Fig. DM1H Bottom View [19] [35] [34] [25] [23] [24] [26] [27] [22] [28] [20]...
Page 122
All manuals and user guides at all-guides.com (S-1) (S-1) (L-1) (L-3) (L-2) (S-1A) (P-1) Installation of [3] and [6] First, insert [6] diagonally in [3] as shown below. Then, install [6] in [3] while pushing (L-1) in the direction of the arrow.
Page 123
All manuals and user guides at all-guides.com [11] (S-4A) (L-4) [49] (P-3) [13] [50] Removal of [11] [12] (L-12) 1) Remove screw (S-4A). 2) Unhook spring (P-2). [10] Release (L-4) while (P-2) holding [12] with a finger. Loosen a finger holding [12] and remove [11].
Page 124
All manuals and user guides at all-guides.com Installation of [13] and [12] (S-5) [14] (S-6) [13] [15] Hook spring (P-3) up to [12] and [13], then install them to (P-3) the specified position so that [12] will be floated slightly while holding [12] and [13].
Page 125
All manuals and user guides at all-guides.com (C-1) turn [22] (S-8) [20] (L-6) [21] [19] Cap Belt Pin on [22] Installation position of Cap Belt [20] Cap Belt [27] Position of pin on [22] Fig. DM12H [19] View for A Fig.
Page 126
All manuals and user guides at all-guides.com Installation of [26] [26] (C-3) Position of Mode Lever when installed Pin of [33] Pin of [37] (S-9) Pin of [36] (L-8) [23] (L-7) Bottom View [24] (C-5) [26] (C-4) (C-2) [28] [27] [25] [29] [30]...
All manuals and user guides at all-guides.com ALIGNMENT PROCEDURES OF MECHANISM The following procedures describe how to align the Alignment 1 individual gears and levers that make up the tape Loading Arm (SP) and (TU) Assembly loading/unloading mechanism. Since information about the state of the mechanism is provided to the Install Loading Arm (SP) and (TU) Assembly so that System Control Circuit only through the Mode Switch,...
All manuals and user guides at all-guides.com DECK PARTS LIST Loca- TSB P/N Reference No. Description Loca- tion No. TSB P/N Reference No. Description tion No. B558 P000483820 MMDZB12MF003 LOADING MOTOR RF-500TB- P000468620 1VSA14761 CYLINDER ASSEMBLY(N236C) 12560 MK14 PAL 6HD B559 P000468020 0VSA13450...
Page 133
All manuals and user guides at all-guides.com Appendix: RD-XV47KE, RD-XV47KB, RD-XV47KF REVISION HISTORY Date Reason for Change 07/31/07 Changed Parts List due to add the TSB P/N for LED, Location No. D555...
Page 134
All manuals and user guides at all-guides.com...