Rules For Safe Driving; Assistance Service - Peg-Perego Corral T-Rex Pink Use And Care Manual

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
2nd GEAR (if present)
Initially, use in 1st gear is recommended. Before
enabling 2nd gear, check that the child has learned to
use the handlebars/steering wheel, 1st gear and the
brake correctly, and has become familiar with the
vehicle.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
• If the vehicle is overloaded on steep slopes, the
overload cut-out will immediately disconnect the
power. If this happens, REMOVE THE FOOT FROM
THE ACCELERATOR. The electrical brake will be
activated, slowing down the descent of the vehicle.
• Only for 12 and 24 Volt vehicles: in first gear the
vehicle has a differential effect like a real motor
vehicle; on smooth terrain and with just one child
on board, the two wheels can turn at different
speeds and they can slip and slow down.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by
an assistance centre.

ASSISTANCE SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://global.pegperego.com/toys-
site/support/
The item's serial number must always be quoted.
See the page on spare parts to find out how to
identify the serial number.
Peg Perego always strive to best satisfy their
customers' needs. Knowing the opinions of our
customers is therefore very important and
valuable to us. We would be very grateful if, once
you have used the product, you would fill out the
CONSUMER SATISFACTION QUESTIONNAIRE
which you can find on the internet at:
www.pegperego.com, making any
observations or suggestions you might have.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
ASSEMBLY
1 • Push the gear lever down into its housing until it
clicks into place.
2 • Position the bumper on the front of the frame.
Raise.
3 • Fit the bumper.
4 • Position and fix the dashboard.
5 • Slot the handlebars into their holder. Make sure
that the ribs on the handlebar section fit
perfectly into the grooves in the holder, as
shown in the figure.
6 • Fasten the newly assembled handlebar unit in
place with a screw.
7 • Insert the handlebar cap.
8 • Push the grips on all of the way to the end. Make
sure that the teeth connect properly.
9 • Slot the handlebar unit onto the steering column.
Push upwards to bring the 2 holes together, as
shown in the figure.
10 • Secure the unit with a screw.
11 • Fit the mudguard wing, making sure that you
completely insert first the 2 clips and then the
pin.
12 • Put the screw in the pin and screw on the wing.
Do the same for the other wing.
13 • Connect the exhaust pipe inserting the tab A in
the bodywork hole.
14 • Fix the exhaust pipe with the screw supplied. Do
the same for the other pipe.
15 • Slip the aerial into the special hole and press..
16 • Push the 4 hub covers firmly on, making sure
that the tabs fit into the slots in the hubcaps.
17 •Turn the red lock behind the saddle until it is in
the position shown in the figure. A: The saddle is
locked. B: The saddle can be opened.
18 • Press on the rear of the bodywork to facilitate
opening the saddle. Open the saddle.
19 • Connect the plugs. When you have finished,
remember to close and fix down the saddle. The
vehicle is ready to use.
VEHICLE FEATURES AND
INSTRUCTIONS FOR USE
20 • PEDAL: Accelerator only, brake is automatic.
21 • GEAR LEVER: the vehicle has three gears: 2
forward and 1 reverse. Please note: when it is
removed from the packaging the vehicle only
travels in first gear and reverse. In order to be
able to use second gear follow the instructions in
the illustrations below.
1 = first gear
2 = second gear
R = reverse
22 • Remove the screw in the second gear lock.
23 • Turn the second gear lock as shown in the figure.
24 • Replace and tighten the screw in the second gear
lock.
25 • The gears are now all available. Move the lever
backwards to change into second gear.
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
26 • Rotate the red lock behind the saddle and open
it. Press on the rear of the bodywork to facilitate
opening the saddle. Unplug vehicle wiring
terminal from battery terminal, by pressing
terminals on side and pulling apart.
27 • Remove the battery holder by pressing the
thinner end so that the tab comes out.
28 • Replace the battery. Put the battery holder back
in place, inserting the wider end first. Reconnect
the plugs and close the saddle.
BATTERY RECHARGE
WARNING: BATTERY CHARGING AND EVERY
OTHER OPERATION ON THE ELECTRICAL
SYSTEM MUST BE CARRIED OUT BY ADULTS
ONLY. THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
29 • Unplug vehicle wiring terminal A from battery
terminal B, by pressing terminals on side and
pulling apart.
30 • Plug the battery charger terminal to a wall
outlet following the instructions enclosed.
Connect the plug B to the battery charger plug
C.
31 • Once the charge is completed unplug recharger
from wall outlet. Unplug recharger cord terminal
C from battery terminal B.
32 • Plug battery terminal A into vehicle wiring
terminal B. Close saddle.