Using An Sd Card - Korg KROSS Operation Manual

2. Access the G-INPUT/CTRL> FOOT page.
Proceed as follows.
Press the GLOBAL/MEDIA button to enter mode.
Press the MENU button to access the function list. Use
the ▼ (PAGE+) and ▲ (PAGE–) buttons to select G-
INPUT/CTRL, and press the OK (MENU) button.
Use the ▼ (PAGE+) and ▲ (PAGE–) buttons to select
the G-INPUT/CTRL> Foot page, and press the OK
(MENU) button.
3. Set "Foot Switch Assign" to either Program Up or
Program Down.
If you choose Program Up, the next program number up
will be selected each time you press the foot switch.
If you choose Program Down, the next program number
down will be selected each time you press the foot
switch.
Use the cursor ▲▼ buttons to select Foot Switch Assign.
Press the ENTER button to access the list, and use the
cursor ▲▼ buttons to select Program Up or Program
Down. Press the ENTER button to confirm your choice.
4. Set the "Foot Switch Polarity" to match the polarity of
the pedal you've connected.
If you've connected the optional PS-1 or PS-3 pedal,
choose (–) KORG Standard. Use the cursor ▼ button to
select the parameter, and press the ENTER button. The
setting will alternate on/off each time you press the
button.
Now, the foot switch will step through the Programs, one
by one.
5. If you want to preserve this setting even when the
power is turned off, be sure to Write the data. (see
page 104)
6. Press the PROG button to enter PROG> MAIN, and
press the foot switch to change the Program.
Note: This setting also works in the same way for selecting
combinations or favorites.
Note: With the Program Up/Down method, you can't switch
programs while the sound select list is open. Use the method
explained below in "Assigning the foot switch to Value Inc/
Dec".
Assigning the foot switch to Value Inc/Dec
This lets you use the Assignable Foot Switch to duplicate the
functions of the front-panel cursor ▲▼ buttons.
This method is convenient if you want to open the Sound
select list and switch programs while viewing the program or
combination menu.
1. Follow steps 1–2 under "Assigning the foot switch to
Program Up/Down," above.
2. At the top of the page, set the Foot Switch Assign
parameter to Value Inc (or Value Dec).
3. Now, the foot switch will act just like you're pressing
the front-panel cursor ▲▼ buttons.
Note: The foot switch will work like this for the entire
KROSS–not just when the Sound select list is open.
Connecting a foot pedal
If you connect an optional EXP-2 foot controller or XVP-10
expression/volume pedal to the ASSIGNABLE PEDAL
jack, you can use it to apply modulation to sounds or effects,
or to adjust the overall volume.
This pedal will always function in the same way regardless
of the Program, Combination, or Song you've selected. You
can assign the function in the Global/Media mode.
Like the Assignable Foot Switch, described above, the Foot
Pedal can be used for many different functions, including:
• Master Volume
• Channel Volume, Pan, or Expression
• Assignable sound modulation, as several different AMS
or Dmod sources
• Effects Send level control
• Use various KROSS controls (Modulation wheel, etc.)
1. Connect an optional XVP-10 or EXP-2 to the
ASSIGNABLE PEDAL jacks.
2. Use the Foot Pedal Assign parameter (G-INPUT/
CTRL> FOOT page) to specify the function that will
be controlled by the foot pedal.
Adjust settings as explained in "Assigning the foot switch
to Program Up/Down".

Using an SD card

You can use an SD card to save or load programs,
combinations, and song data, and also for audio recording.
Types of SD card you can use
SD card specifications
SD memory cards up to 2GB and SDHC memory cards up to
32GB are supported.
SDXC memory cards are not supported.
MS-DOS format FAT16 or FAT32 are supported.
Media is not included. You will need to purchase it
separately.
Formatting media
Some consumer electronics products that use SD cards
utilize their own proprietary format method. Before using an
SD card with the KROSS, you must format it on the
KROSS. (see page 108)
Inserting/removing an SD card
Inserting an SD card
• Insert an SD card in the SD card slot.
With the card label facing upward, insert the connector
end of the card into the SD card slot and press it in until
you hear a click.
Connections Using an SD card
21