Special Safety Instructions - EINHELL EXPERT TE-CC 315 U Original Operating Instructions

Anleitung_TE_CC_315_U_SPK8__ 19.11.12 15:56 Seite 27
the moving parts are working correctly, that they
do not jam, and that no parts are damaged. Make
sure that all parts are fitted correctly to ensure
that the equipment remains safe to use. Unless
otherwise stated in the operating instructions,
damaged guards and parts have to be repaired or
replaced by a customer service workshop.
Damaged switches have to be replaced by a
customer service workshop. Never use tools with
a switch that cannot be turned on and off.
20. Important.
- For your own safety you must only use the
accessories and additional units listed in the
operating instructions or recommended or
specified by the manufacturer. The use of
mounted tools or accessories other than those
recommended in the operating instructions or
catalog may place your personal safety at risk.
21. Repairs may only be carried out by a
qualified electrician
- This electric tool complies with the pertinent
safety regulations. Repair work must only be
carried out by a trained electrician, otherwise the
equipment may cause accidents.
22. Connect up a vacuum extraction system
- If there are provisions for connecting up a
vacuum extraction system, make sure that such a
system is fitted and in use.

Special safety instructions

1. Safety actions
Blades that are deformed or cracked must not be
n
used.
If the table insert is worn, replace it.
n
Use only blades which are recommended by the
n
manufacturer and comply with EN 847-1. When
changing the blade, make sure that the cutting
width is not smaller and the saw plate not bigger
than the thickness of the splitter.
Make sure that the chosen blade is suitable for
n
the material that is to be cut.
If necessary, wear suitable personal protection
n
equipment. This could consist of:
- Ear plugs to prevent the risk of damaging your
hearing;
- A breathing mask to avoid the risk of inhaling
hazardous dust.
- Always wear gloves when handling saw blades
and rough materials. Whenever practicable, saw
blades must be carried in a container.
The following can have an influence on dust
n
development:
- Worn, damaged or cracked saw blades
- Recommended capacity of the vacuum
extraction system: 20 m/s
- Proper guidance of the workpiece
Blades made of high-alloy high-speed steel
n
(HSS) must not be used.
Keep the push stick or handle for a push block at
n
the machine at all times, even when you are not
using them.
2. Maintenance and service
The following conditions can have an influence
n
on noise impact on the operator:
- Type of sawblade (e.g. saw blades designed to
reduce noise development)
- Material of the workpiece
- The force with which the workpiece is pushed
against the sawblade
Faults on the machine or its guards, safety
n
devices and blade must be reported to the
person in charge as soon as they are
discovered.
3. Safe operation
Use a push stick or the handle with a push block
n
to feed the workpiece safely past the saw blade.
Use the splitter and set it correctly.
n
Use the upper blade guard and set it to the
n
correct position.
Do not cut rebates or grooves without fitting a
n
suitable guard, e.g. a tunnel-type guard, over the
saw table.
Circular saws must not be used for slotting jobs
n
(cutting grooves which end in the workpiece).
Use only blades whose permissible maximum
n
speed is not lower than the maximum spindle
speed of the bench-type circular saw and of the
material to be cut.
Use only the transport devices to move the
n
machine. Never use the guards for handling or
moving the machine.
While you are moving the machine it is best to
n
cover the top part of the blade, e.g. with the
guard.
Secure long workpieces against falling off at the
n
end of the cut (e.g. with a roller stand etc.)
4. Additional instructions
Give these safety regulations to all persons who
n
work on the machine.
Do not use this saw to cut fire wood.
n
Do not use this saw to cross-cut roundwood.
n
Caution! Hands and fingers may be injured on
n
the rotating saw blade.
The machine is equipped with a safety switch to
n
prevent it being switched on again accidentally
after a power failure.
GB
27