Table of Contents
Advertisement
Quick Links
Important Information ................................................ 2
Safety Information ..................................................... 3
Component Identification .......................................... 3
Specifications ............................................................ 4
Electrical Requirements ............................................ 4
Document # 100578 RevH
Model 5000/5001
Installation ...................................................................5
Operation ....................................................................7
Maintenance ..............................................................13
Cleaning ....................................................................13
Limited Warranty .......................................................15
The Brewer Company, LLC
N88 W13901 Main Street, Suite 100
Menomonee Falls, WI 53051
P 1.888.Brewer.1
F 262.251.2332
www.brewercompany.com
Printed in USA © 2014
Advertisement
Table of Contents
Related Manuals for brewer Access 5000
Summary of Contents for brewer Access 5000
-
Page 1: Table Of Contents
Maintenance ..............13 Specifications ............4 Cleaning ..............13 Electrical Requirements ..........4 Options, Accessories & Common Service Parts ..14 Limited Warranty ............15 The Brewer Company, LLC N88 W13901 Main Street, Suite 100 Menomonee Falls, WI 53051 P 1.888.Brewer.1 F 262.251.2332 www.brewercompany.com Document # 100578 RevH Printed in USA ©... -
Page 2: Important Information
Brewer Model 5000/5001 examination during general examinations conducted by qualified table, call the Brewer Customer Service Department at medical professionals. Read and understand all safety 1.888.Brewer.1. Our trained staff will attempt to assist information, operating instructions, and maintenance you in correcting the problem directly over the phone. -
Page 3: Safety Information
SAFETY INFORMATION Safety Information The primary concern of The Brewer Company is that the Failure to follow instructions with these symbols equipment is operated and maintained with the safety of could result in serious personal injury and/or the patient and healthcare staff in mind. To ensure safe damage to the unit. -
Page 4: Specifications
SPECIFICATIONS Weight of Table .............220 lbs. Operation (With carton and skid)...........265 lbs. Temperature ..........50°F to 104°F Table Weight Capacity ..........500 lbs. Humidity............30% to 75% Stirrup Extension (maximum): ......... 16 in. Electrical Requirements Stirrup Lateral Positions ......4 Lateral Positions ... .120 VAC nominal, 60 Hz, 3 amps maximum ... -
Page 5: Installation
INSTALLATION Overview 1. Carefully remove outer carton by removing the staples Perform the following sequence in order when setting up along the bottom of the carton and lift off table. the table: 2. Unbolt the table from the shipping pallet by removing Unpacking the 4 bolt screws from the pallet with a 1/2”... - Page 6 INSTALLATION (CONTINUED) Leveling the Table (Figure 4) A leveling screw pad is located at each corner under the table’s base. Adjust the four leveling pads, by turning them up or down, using Method 1 or Method 2 to achieve a solid, level installation. Test step by pulling out. If step drags on floor or is difficult to pull out, adjust the front table levelers (not the step levelers) out 1 turn at a time until step pulls out easily.
-
Page 7: Operation
OPERATION General Back Section (Figure 6) 1. Press and hold the release handle, lift back WARNING section upward to raise. Releasing the handle will automatically lock the table in the desired position. EXPLOSION HAZARD Do not use this table in an explosive or oxygen- 2. - Page 8 OPERATION (CONTINUED) Footstep (Figure 7) 1. Place hand into opening in front of step and gently lift while fully extending footstep. WARNING 2. To retract step to stowed position, gently lift while pushing step fully back into cabinet. FALL HAZARD •...
- Page 9 OPERATION (CONTINUED) Stirrups (Figure 8) Retracting the stirrup to the storage position: WARNING 1. Rotate stirrup to the first lateral position (parallel to FALL HAZARD the table). Failure to engage the stirrup lateral locking 2. Fold stirrup down against bar. mechanism could allow patient to lose balance resulting in a fall and personal injury to patient.
- Page 10 OPERATION (CONTINUED) Leg Extension (Figure 9) WARNING Horizontal Positioning FALL HAZARD Push leg extension in fully before allowing patient to get onto or off of table. Failure to push leg extension in fully can cause patient to fall resulting in serious injury. 1.
- Page 11 OPERATION (CONTINUED) Patient Positioning (Figure 10) The table is designed to accommodate the following examination positions: • Full Flat Table Position • Chair Position • Lithotomy (Pelvic) Position Chair Position Full Flat Table Position Lithotomy (Pelvic) Position Figure 10. Patient Positioning Document # 100578 RevH Printed in USA ©...
- Page 12 OPERATION (CONTINUED) Pelvic Lift - Model 5001 Only (Figure 11) Drawer Warmer - Model 5001 Only Raising the seat section to the Pelvic Lift Position: (Figure 11) 1. Raise the front edge of the seat section. WARNING 2. Rotate the pelvic tilt support bar upward to its full BURN HAZARD upright position.
-
Page 13: Maintenance
Figure 12. Bottom Drawer Moved to Show Fuse Location 5. Reassemble drawer. Removing Fuse Installing Fuse Figure 13. Fuse Location CLEANING Please see the Brewer Cleaning Guidelines in the “Resources” area of www.brewercompany.com. Document # 100578 RevH Printed in USA © 2014... -
Page 14: Options, Accessories & Common Service Parts
OPTIONS, ACCESSORIES, AND COMMON SERVICE PARTS Listed below are the accessories and service kits which are authorized for use with this table. Description Order No. Use/Restrictions Replacement Upholstery 5115-XX Intended Use - Replacement top with hardware for 5000 and 5001, examination tables in standard colors. Special Upholstery 5115-SP Intended Use-Allows the purchase of specialty vinyls... -
Page 15: Limited Warranty
Brewer warrants its Products to be free from defects in parts and workmanship under normal use and service for a period detailed in the table below from the date of delivery to original end user. Brewer will not be responsible for any Product failure due to abuse, modification or improper use, or for any use which exceeds the published capacity of the Product.