THUNDER TIGER Titan x50 Instruction Manual page 23

Tail Unit Assembly-2 / 尾旋翼組組裝-2
Bag J+K
No. Material No. Description
1 BK2190 CARBON VERTICAL FIN
2 HMM3Z NYLON NUT,M3
3
BK0046 TAIL UNIT HOUSING-L
4
HMV1150ZZSY BEARING,d5xD11xW5
5
BV0052 TAIL IDLE PULLEY
6
HMC3-20B SOCKET SCREW,M3x20
7
HMC3-25B SOCKET SCREW,M3x25
8
HMC3-16B SOCKET SCREW,M3x16
HMM3Z
NYLON NUT,M3
止鬆螺帽,M3
HMV1150ZZSY
BEARING,d5xD11xW5
滾珠軸承,d5xD11xW5
HMC3-20B
SOCKET SCREW,M3x20
內六角螺絲,M3x20
HMC3-25B
SOCKET SCREW,M3x25
內六角螺絲,M3x25
HMC3-16B
SOCKET SCREW,M3x16
內六角螺絲,M3x16
All manuals and user guides at all-guides.com
名稱
碳纖維垂直尾翼
止鬆螺帽,M3
尾座(左)
滾珠軸承,d5xD11xW5
尾舵輪
內六角螺絲,M3x20
內六角螺絲,M3x25
內六角螺絲,M3x16
(13)
(14)
1. Remove the tape from the rear of the belt and twist it toward left by 90° (view from tail to nose), then
warp around the Metal Tail Pulley.
2. Assembly the Tail Pulley Case, but do not over close these 2-half of the Tail Case tightly and ensure
the Tail Pulley runs effortlessly.
3. Attach the Carbon Vertical Fin.
4. Assembly the Tail Support Bracket & Tail Boom Supports as drawing, but do not tighten at this step;
the position of Tail Support Bracket may be adjusted later.
5. Attach Tail Rotor Blades by the Socket screws but do not over tighten.
6. Ensure the leading edge of the blades are toward proper side as shown.
1. 移去皮帶尾端膠帶並向左扭轉90度 （由機尾朝機首看），繞在金屬尾輪上。
2. 組裝尾座組，切勿過度迫緊兩側尾座殼，確認金屬尾輪運轉順暢。
3. 裝上碳纖垂直安定面。
4. 依圖示將支撐桿固定座及尾管支撐桿鎖附，支撐桿固定座暫時不鎖緊，以便後續微調。
5. 裝上尾旋翼，切勿過度鎖緊。
6. 請確認旋翼前櫞朝向正確方向（如圖示）
HMJ2-8N
SELF TAPPING SCREW-M2x8
自攻螺絲(細)-M2x8
HMC3-14B
SOCKET SCREW-M3x14
內六角螺絲-M3x14
Qty No. Material No. Description
1 9 BK0797 BRACKET-UPPER
10 10 BK0798 BRACKET-LOWER
11
1 BK0524-T TAIL SUPPORT ROD
12
1 BK0447 TAIL SUPPORT ROD END
13
1 HMJ2-8N SELF TAPPING SCREW-M2x8
14
4 HMC3-14B SOCKET SCREW-M3x14
15
2 BK0404-B TAIL BLADE(BLACK)
4
(6)
(7)
(8)
(6)
(9)
(10)
BELT INSTALLATION 傳動皮帶安裝
Rotate the belt 90° counterclockwise.
逆時針方向旋轉皮帶90°
(11)
(15)
(8)
(2)
(15)
-22-
名稱
固定座(上)
固定座(下)
尾管支撐架
尾管支撐架接頭
自攻螺絲(細)-M2x8
內六角螺絲-M3x14
尾旋翼(黑)
(5)
(4)
(3)
(1)
(12)
(13)
(2)
(2)
Metal Tail Pulley
金屬尾惰輪
Guide Pulley
惰輪
Autorotation TailDrive Pulley
尾驅動輪
(2)
Qty
1
1
2
4
4
2
2
(2)
(2)
Belt
皮帶