INSTRUCTION MANUAL INSTRUCTION MANUAL 組裝說明書 組裝說明書 Electric Version . Flybarless Edition No.4757 This radio control model is not a toy! Before beginning assembly, please read this manual thoroughly. 本產品為高性能模型非一般玩具,組裝與操作前請詳閱本產品說明書。 The contents are subject to change without prior notice due to product improvements and specification changes.
Electric Version . Flybarless Edition CONTENTS INTRODUCTION INTRO & CAUTION / 簡介與注意事項 OTHER ITEMS REQUIRED / 其餘必須配件 MANUAL FORMAT / 說明書使用方式 ASSEMBLY / 組裝步驟 Main Rotor System / 主旋翼機構組裝 Main Rotor Head Linkage Rod Installation / 主旋翼頭連桿組裝 Tail Boom Bracket Assembly / 尾管固定座組裝 Main Frame / 本體組裝...
INTRODUCTION / 簡介 Thank you for purchasing the Thunder Tiger Titan X50 R/C helicopter. This new helicopter is the latest innovation by Thunder Tiger. It has the perfect combination of flying stability and the agility for 3D flying. This helicopter is an excellent choice for flying enthusiasts like you. For convenient assembly and safe operation of the helicopter, please read the instructions carefully.
Page 4
FLIGHT SAFETY CHECKLIST / 飛行前安全確認工作項目 1. Make sure that the transmitter battery is fully charged before flying. 2. Make sure all control surfaces are operated properly before flying. 3. Do a range check of the radio before the first flight. The electronic equipment must operate properly at a range of at least 5 meters (18 ft) even with the transmitter antenna collapsed.
OTHER ITEMS REQUIRED 需自行準備的配件 RADIO SET / 遙控系統 Receiver Battery Switch Harness 接收機電池 1000mAh 接收機 具備充電線的開關組 Transmitter (helicopter type Servo Gyro only, 6 or more channels) 伺服機 陀螺儀 發射機(需具備直昇機控制功能 的6動以上遙控器) POWER SYSTEM / 動力系統 Electric Brushless Motor Electronic Speed Controller Foam 8~12S Li-Po Battery Pack 無刷馬達...
MANUAL FORMAT / 說明書使用方式 How to read the instruction manual? Example 說明範例 說明書導讀 A: Indicates the assembly step number and the parts bags that are to be assembled. B: Displays actual size drawings, and part quantities used. C: All parts, except screws, are identified by its order numbers.
Main Rotor System / 主旋翼機構組裝 Bag A Material No. Description Material No. Description 名稱 名稱 BV2574 METAL MAIN ROTOR GRIP SET 金屬旋翼轉座組 BK2573 OUTER DAMPER, 7mm 外避震墊圈, 7mm BK2575 FL METAL ROTOR GRIP LEVER 無平衡翼金屬轉座擺臂 BK2572 INNER DAMPER, 7mm 內避震墊圈,7mm BK2576 FL METAL ROTOR GRIP POST 無平衡翼金屬連接座...
Main Rotor Head Linkage Rod Installation / 主旋翼頭連桿組裝 Bag A Material No. Description Material No. Description 名稱 名稱 BK2236 UPPER BRG 上軸承座 BK0088 WASHER, d3xD5xW0.5 墊片, d3xD5xW0.5 BK2219 FRAME SPACER 六角連接支柱 BK0171 插銷 HMV6800ZZY BEARING, d10xD19xW5 滾珠軸承, d10xD19xW5 HMS15 E RING E型扣環...
Main Frame / 本體組裝 Bag C+D Material No. Description Material No. Description 名稱 名稱 SIDE FRAME ELEVATOR WASHER MOUNT SET(L) BK2255 機身側板 BV2238 升降舵墊片座組(左) SOCKET SCREW,M2x4 ELEVATOR WASHER MOUNT SET(R) HMC2-4B 內六角螺絲,M2x4 BV2237 升降舵墊片座組(右) BK2551 RUBBER GROMMETS 橡膠墊圈 Completed View 組裝完成...
Page 11
Main Frame / 本體組裝 Bag D Material No. Description Material No. Description 名稱 名稱 BK2225 BK2273 LOWER BRG 下軸承座 CONTROL ARM TRAY 控制搖臂座 HMV6800ZZY BEARING, d10xD19xW5 HNX3-12B S.B.H SELF TAPPING SCREW 滾珠軸承, d10xD19xW5 半圓頭內六角自攻螺絲 BK2219 FRAME SPACER HMC3-10B SOCKET SCREW,M3x10 六角連接支柱...
Landing Skid / 腳架組組裝 Bag E Material No. Description Material No. Description 名稱 名稱 BK0023 ELEVATOR CONTROL ARM LINK BK2261 LANDING SKID 升降舵連接座 腳架 BK0084 PIN,D2x22.8 BK0064T SKID PIPE 固定銷,D2x22.8 底座圓管 BK2514 BK0065 METAL ELEVATOR CONTROL ARM SKID PIPE END CAP 金屬升降舵控制臂...
Main Gear Set / 主齒輪組裝 Bag F Material No. Description Material No. Description 名稱 名稱 ONE WAY BEARING SHAFT SOCKET SCREW,M3x10 BK2282 單向軸套 HMC3-10B 內六角螺絲,M3x10 BV2281 ONE WAY CLUTCH HOUSING BK0087 WASHER,d3xD8xW1.4 單向離合組 墊片,d3xD8xW1.4 BK2581 MAIN GEAR, 135T 主齒輪, 135T BK1197 MAIN SHAFT BOLT,M3x20 內六角半牙螺絲,M3x20...
Control Arm Set / 控制臂組裝 Bag F+I Material No. Description Material No. Description 名稱 名稱 BK2248 PHASING CONTROL TRACK BK0088 WASHER, d3xD5xW0.5 相位控制導軌 墊片, d3xD5xW0.5 BK2249 CANOPY RETAINING POST BK0077 COLLAR, d3xD4xW6 機殼固定鋁柱 軸環, d3xD4xW6 HME3-18B SET SCREW,M3x18 HSA3-10 BUTTON HEAD SOCKET SCREW, M3x10 無頭內六角螺絲,M3x18 半圓頭內六角螺絲, M3x10 HMC2-4B...
Power Motor Installation / 動力馬達安裝 Bag K Material No. Description Material No. Description 名稱 名稱 HMC3-10B BK2584 SOCKET SCREW,M3x10 內六角螺絲, M3x10 MOTOR PINION-15T 馬達齒-15T BK0087 WASHER,d3xD8xW1.4 HMC3-8B SOCKET SCREW,M3x8 墊片, d3xD8xW1.4 內六角螺絲, M3x8 BK2260 UPPER MOTOR MOUNT HME4-3B SET SCREW M4×3 馬達上座...
Main Rotor Blade / 主旋翼安裝 Bag KPI Material No. Description 名稱 HMC4-27B SOCKET SCREW,M4x27 內六角螺絲, M4x27 HMM4Z NYLON NUT,M4 止鬆螺帽, M4 1. You may need to adjust the linkage to ensure the blade tracking. Please refer page 26, 〝Blade Tracking Adjustment.〞 2.
Radio System Setup / 遙控系統設定 Warning! / 警告! For safety, please ensure the motor has been deactivated and will not drive the main rotor head before performing following setting processes. You may just unplug 2 of the wires from the motor and the ESC or move the motor with pinion away from the main gear to avoid a rotating rotor head.
Index of Linkage Length / 連桿長度索引 76 mm / 2.992” 55 mm / 2.1655” 76.6 mm / 3.015” 82.6 mm / 3.252” 79.9 mm / 3.145” Swashplate & Servo Movement Setting / 十字盤及伺服機動作設定 As going through these setup procedures, ensure there is none of the controls bind at full travel. Next, please refer below illustrations to ensure the direction of servo movement and swash mixing settings are correct for the controls properly.
Tail Control and Gyro Setup 尾舵控制及陀螺儀控制 It is recommended to use a Heading Lock Gyro. With a Heading Lock Gyro, you may not use the trim and the revolution mixing function of tail control. First, choose the length of the tail servo arm referring to the manual of the Gyro. You may try 13.5mm as the starting setting.
Setting Up Data for Your Reference 參數設定參考 The following is the setting up data of pitch curve and throttle curve for your reference only. Please ask experienced pilot to help you if you have never done this before. 下列參數設定僅供參考,請依實際狀況進行調整,或詢求有經驗的玩家協助。 ■ Beginner / 一般飛行 Throttle Curve 油門曲線...
Blade Tracking Adjustment / 主旋翼軌跡調整 CAUTION / 警告 For safety, ensure to keep a safe distance from the helicopter at least 10 meter (30 feet) while making tracking adjustment. 安全起見,進行主旋翼軌跡調整時,請至少與直昇機保持10米(30呎)的安全距離。 color tape / 色標貼 Out of Track / 雙槳 Adjustment is necessary.
5. Always avoid any puncture of the battery pack at all times. Neither Thunder Tiger nor our distributoers/retailers assume liability for failures to comply with these cautions, safety recommended and instruction manual. Users assume all risks associated with Li-Po battery packs.
Page 30
METAL TAIL ROTOR HUB SWASHPLATE CONTROL ROD 尾旋翼組(黑) 金屬旋翼頭制動器 金屬十字盤組 十字盤穩定桿 金屬尾旋翼固定座 PV1339 PV1331-1 PV1335 PV1339-1 PV1340 OUTER DAMPER(7mm) METAL TAIL GRIP,X50 MAIN SHAFT BEARING BLOCK INNER DAMPER(7mm) MAIN GEAR WASHER 金屬尾旋翼座(軸傳),X50 主軸上下軸承座 外避震墊圈(7mm) 主齒輪墊片 內避震墊圈(7mm) PV1341-1 PV1342 PV1345 PV1346...
Page 31
SPARE PARTS / 維修零件包 PV1375 PV1366 PV1367 PV1368 PV1371 TAIL DRIVE SHAFT SET TAIL GEAR SET TAIL GEAR MOUNT SET TAIL PITCH CONTROL LEVER SET BEARING BLOCK SET 尾驅動軸組 傘齒輪固定座 尾旋翼控制桿組 軸傳軸承座組 傘齒輪-25T (10) (10) PV1376 PV1377 PV1378 PV1388 PV1379 TAIL DRIVE SHAFT BRG SET ROD GUIDE TAIL ROTOR SHAFT...
Page 32
SPARE PARTS / 維修零件包 3915 PV1382 PV1425 PV1431-G PV1604 FBL CARBON BLADE 600mm METAL FB MAIN ROTOR HUB METAL TAIL CASE ABS CANOPY-GREEN SERVO MOUNTING SET 無平衡翼碳纖彩槳600mm 金屬無平衡翼主旋翼固定座 金屬尾座 ABS 機殼 (綠色) 伺服機墊片組 PV1383 PV1384 PV1385 PV1386 PV1387 METAL FB CONTROL LEVER SET METAL FB ROTOR GRIP LEVER SET METAL FB ELEVATOR LEVER ROD METAL 120°...
Page 37
SPARE PARTS LIST / 維修零件包表格 Description 中文名稱 Part No. Description 中文名稱 Qty Index Page PV1383 METAL FB CONTROL LEVER SET 金屬無平衡翼控制搖臂組 BV2508 METAL FB CONTROL LEVER SET 金屬無平衡翼控制搖臂組 HSA3-14 BUTTON HEAD SOCKET SCREW, M3X14 半圓頭內六角螺絲, M3x14 BK0077 COLLAR, D3XD4XW6 軸環, d3xD4xW6 BK0088 WASHER, D3XD5XW0.5 墊片, d3xD5xW0.5...
Page 38
SPARE PARTS LIST / 維修零件包表格 Description 中文名稱 Part No. Description 中文名稱 Qty Index Page HSA3-10 BUTTON HEAD SOCKET SCREW, M3x10 半圓頭內六角螺絲, M3x10 HMC3-10B SOCKET SCREW, M3x10 內六角螺絲, M3x10 6,10,11,12,15,16,19 PV1415 METAL TAIL SUPPORT BRACKET 金屬尾支撐桿固定座 BK2563 METAL TAIL SUPPORT BRACKET(UPPER) 金屬固定座(上) BK2564 METAL TAIL SUPPORT BRACKET(LOWER)
Page 39
SPARE PARTS LIST / 維修零件包表格 Description 中文名稱 Part No. Description 中文名稱 Qty Index Page BK0539-1 SERVO MOUNT 伺服機固定板 HMC3-20B SOCKET SCREW, M3x20 內六角螺絲, M3x20 HMC3-25B SOCKET SCREW, M3x25 內六角螺絲, M3x25 HMC3-30B SOCKET SCREW, M3x30 內六角螺絲, M3x30 HMM3Z NYLON NUT, M3 止鬆螺帽, M3 -38-...