Graco Dyna-Star HP Manual

Hide thumbs

page of 9

/ 9
Bookmarks

Quick Links

Download this manual

Dyna-Star

Low Level Indicator Kit; Dip

Stick Kit

Provides a visual reference of remaining fluid level in a tank / reservoir used with the

Dyna-Star HP or HF pump. Low Level Indicators equipped with a user supplied alarm will

also provide an audible and/or visual notification of a low fluid level. For professional use

only.

Low Level Indicator Part No: 77X522

Includes sight glass, electric low level switch and cable. Requires follower plate. Cannot be used with Auto-Fill

Dip Stick Part No: 77X530 - 90#; 77X531 - 60#

Cannot be used with a follower plate or Auto-Fill Shut Off.

Important Safety Instructions

Read all warnings and instructions in this

manual and in the Dyna-Star HP or HF Pump

instruction manual. Save all instructions.

HP or HF Pump

Part No. 77X522

332515F

Shut Off.

Part No. 77X530 or 77X531

Need help?

Do you have a question about the Dyna-Star HP and is the answer not in the manual?

Questions and answers

Summary of Contents for Graco Dyna-Star HP

Page 1 Provides a visual reference of remaining fluid level in a tank / reservoir used with the Dyna-Star HP or HF pump. Low Level Indicators equipped with a user supplied alarm will also provide an audible and/or visual notification of a low fluid level. For professional use only.
Page 2: Installation
Installing Low Level Indicator Warnings 1. Disconnect Dyna-Star pump from main power source. See the Dyna-Star HP and HF Pump Instruction manual 2. If unit has already been in service, relieve pressure for additional warnings. (see Pressure Relief procedure, page 2).
Page 3 6. Remove screws (e) and washers (f) holding Dyna-Star Pump to reservoir cover (b) and remove 8. (If previously installed) remove follower plate from pump from cover (F . 4). inside reservoir. 9. Determine the correct cable length to use for your pump reservoir.
Page 4 11. Remove one of the screws (k) from the follower plate (m) (F . 7). 12. Install screw (k) through the hole (n) in the cable bracket (p) located at the end of the low level cable (j) and then through the screw hole (r) in the follower plate (m) (F .
Page 5 Installation 16. Slide pump down-tube through hole in the center of 17. Replace screws (e) and washers (f) and wrench the reservoir cover (b) and hole in the center of the tighten securely (F . 12). follower plate (m) as shown in F .
Page 6 PINS 1 and 3 of the DIN, Form “A” Field Wireable Adapter. See F . 14. . 14 2. Connect Dyna-Star pump to main power source. 3. Start system following pump start up procedure included in the Dyna-Star HP or HF Pump Manual provided with your system. 332515F...
Page 7 Low Level Visual Indication Sight Glass Low Level Visual Indication Sight Glass sight Red (R) sight Green (G) glass glass Green (G) . 15 . 17 Normal Level Mark (F . 15) - Red rod is completely covered by the green tube (G) and no red is visible in Low Level Mark (F .
Page 8 Dip Stick Installation Dip Stick Installation 1. Remove plug (a) from cover (b). Discard plug, you will not reuse it (F . 18). . 18 . 19 2. Slide dipstick through hole (aa) in cover (b) and into reservoir (F .
Page 9 Low Level Indicator Technical Data Low Level Indicator Technical Data Low level sensor switch Normally open sensor switch, closes upon low level Operating temperature range -50°F to 150°F (-45°C - 65°C) Electrical Ratings Switching Power 10 Watt Max. Switching Current 0.4A-Max.

This manual is also suitable for:

Dyna-star hf