Summary of Contents for Texas Instruments TLV320AIC12
Page 1
TLV320AIC12, TLV320AIC13 TLV320AIC14, TLV320AIC15 User’s Guide October 2002 Data Acquisition Products SLAU097...
Page 2
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
Page 3
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product incorporating the goods.
Page 4
EVM schematic located in the EVM User’s Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2002, Texas Instruments Incorporated...
Page 5
How to Use This Manual Preface Read This First About This Manual This users guide describes the operation and use of the TLV320AIC12 codec family. A complete circuit description, schematic diagram, and bill of materials are also included. How to Use This Manual This document contains the following chapters: Chapter 1—EVM Overview...
Page 6
Related Documentation From Texas Instruments Related Documentation From Texas Instruments To obtain a copy of any of the following TI documents, call the Texas Instruments Literature Response Center at (800) 477-8924 or the Product Information Center (PIC) at (972) 644-5580. When ordering, identify this booklet by its title and literature number.
TLV320AIC13 TLV320AIC14 TLV320AIC15 This guide refers to the TLV320AIC12 only, since the remaining device feature sets are subsets of the TLV320AIC12. Any important differences are noted. Figure 1−1. EVM The EVM is split into two complementary halves as shown in Figure 1−1.
Chapter 2 Digital Interface The digital signals required to operate this codec originate from the 40-pin connector—J1. There are two methods to drive the digital interface: Create a custom interface between the codec EVM and the host system. Alternatively, if a TI DSK (DSP starter kit) is the host system, a develop- ment platform is available from TI.
Codec-to-Platform 2.1 Codec-to-Platform The TLV320AIC12, 13, 14, and 15 mate with the development platform via a 40-pin Samtec connector. The mating connector (Samtec part number, TSM-120-01-T-DV-P) is used on the development platform to provide the electrical connections necessary. Consult Samtec at www.samtec.com...
Codec-to-Codec Table 2−1. Pinout for 40-Pin Connector (Continued) Pin Number Signal Description J1.33 3.3V_A_DRV Output driver supply 3.3 V J1.34 AGND Analog ground J1.35 3.3V_A_DRV Output driver supply 3.3 V J1.36 AGND Analog ground J1.37 3.3V_A Analog 3.3 V J1.38 AGND Analog ground J1.39...
Jumper Options 2.3 Jumper Options There are various jumpers on the board that can be configured in various ways, depending upon the user’s requirements. Their functions are briefly presented in Table 2−2: Table 2−2. Jumper Options Jumper Function Selects whether U2 is either a master or a slave codec Used along with W2 for correct polarity for FSD Manages FSD from the master.
Jumper Options Table 2−3. Stand-Alone Slave Jumper Settings Jumper 1−2 2−3 Not inserted Inserted Inserted Not inserted Inserted Not inserted Not inserted Inserted P1.9–P1.10 P1.11–P1.12 Inserted Inserted P1.13–P1.14 Inserted Inserted 2.3.2 Single Master Only This configuration applies to EVM1 only. When a single codec is to be used in master mode, U2 is always the master codec.
System Level Considerations 2.3.4 Slave/Slave Cascade This configuration applies to additional EVMs that may be installed for additional channels. It does not apply to EVM1. Both U1 and U2 are slave codecs to the master codec, which resides on EVM1. Follow the jumper settings detailed in Table 2−6.
Table 3−1 indicates the applicable connectors for each codec in the family. In order to enable a wide range of sources and loads to be connected to the codecs, screw terminals have been used wherever possible. Table 3−1. Analog Interface Connectors TLV320AIC12 TLV320AIC13 TLV320AIC14 TLV320AIC15...
Chapter 4 EVM Operation The EVM is shipped from the factory in master/slave cascade mode. To check if the EVM is working properly, simply install the EVM onto the development platform, and apply power to the DSK. The EVM should begin working immediately.
Chapter 5 TLV320AIC12/13/14/15 Bill of Materials The following table contains a complete bill of materials for the TLV320AIC12/13/14/15 family of EVMs. The schematic diagram is also provided for reference. Contact the Product Information Center or e-mail dataconvapps@list.ti.com for questions regarding this EVM.
Page 22
Used Value Ref Des Description Vendor Part number W1 W2 W3 3-Position jumper Samtec TSW-103-07-L-S W4 W5 W6 See Assy 1.000/4−40 Nylon hex thread Keystone Electronics 1902E See Assy 0.500/4−40 Nylon hex thread Keystone Electronics 1902C See Assy 4−40 X 1/4 Machine screw PH Building Fasteners PMSSS 440 0025 PH...
Appendix A TLV320AIC12/13/14/15 EVM Schematic The TLV320AIC12/13/14/15EVM schematics are provided on the following pages. TLV320AIC12/13/14/15 EVM Schematic...
Need help?
Do you have a question about the TLV320AIC12 and is the answer not in the manual?
Questions and answers