Summary of Contents for unicraft TWG 20
- Page 1 Operating Instructions Part Washing Unit TWG 20, TWG 80, TWG 150 TWG 20 TWG 150 TWG 80...
-
Page 2: Table Of Contents
1 Introduction .............3 Product identification 1.1 Copyright ............3 Part Washing Unit Item number 1.2 Customer service..........3 1.3 Limitation of liability ..........3 TWG 20 6220020 2 Safety................3 TWG 80 6220080 2.1 Symbol explanation ..........3 TWG 150 6220150 2.2 Responsibility of the operator...... -
Page 3: Introduction
0049 (0) 951 96555-111 This combination of symbol and signal word indica- Email: service@stuermer-maschinen.de tes a potentially hazardous situation which, if not Internet: www.unicraft.de avoided, could result in property damage and env- ironmental damage. Spare parts orders: Fax: 0049 (0) 951 96555-119 Email: ersatzteile@stuermer-maschinen.de... -
Page 4: Responsibility Of The Operator
Safety - The operator must check during the entire period of use of the machine whether the operating in- WARNING! structions he has prepared comply with the cur- This combination of symbol and signal word indica- rent state of the regulations and adjust them if tes a potentially dangerous situation. -
Page 5: Personal Protective Equipment
Safety Electrician: Safety boots The electrician is due to their professional training, knowledge and experience as well as knowledge of the The safety boots protect the feet against bruising, fal- relevant standards and regulations able to work on ling parts and slipping on slippery surfaces. electrical systems and independently recognize and avoid possible dangers. -
Page 6: Intended Use
- Do not operate the unit near heat sources such as Technical Data radiators, open fire or sparks. - Do not inhale health-endangering vapours! (Ob- Model TWG 20 TWG 80 TWG 150 serve the safety data sheets of the cleaning agent manufacturer). -
Page 7: Transport, Packaging, Storage
Transport, packaging, storage Transport, packaging, storage Description of device Delivery Illustrations in this operating manual may differ from the Check the part washing unit for visible transport da- original. mage after delivery. If you discover any damage, imme- diately report it to the transport company or the dealer.. Transport NOTE! Observe the weight of the device during transport... -
Page 8: Assembly, Set Up And Connecting
It is important to ensure that there is enough freedom of movement and sufficient lighting to work. Use protective goggles! Fig. 5: Assembly TWG 20 Use protective gloves! Step 3: Fill the tray with a suitable water-based cleaning solution so that the pump is completely covered (Fig. -
Page 9: Electrical Connection
Assembly, Set up and Connecting Step 11: Installation of the supplied cleaning brush (OP- TIONAL): The cleaning brush can be placed with the end of the hose on the nozzle of the metal hose (Fig. 9). Ensure that the nozzle or brush is shaped so that it points downward toward the center of the tray. -
Page 10: Commissioning
Commissioning - The blue coloured wire must be connected to the ter- minal marked N or black. Use protective goggles! - The brown wire must be connected to the terminal marked L or red. - The yellow-green coloured wire must be connected Wear respiratory protection! to the terminal marked E or green. -
Page 11: Care, Maintenance And Servicing/ Repair
Care, maintenance and servicing/ repair Care, maintenance and servicing/ repair ATTENTION! Disconnect the parts washer from the power supply before carrying out any servicing, maintenance or cleaning work. Service and maintenance work may only be carried out by qualified personnel.. 9.1 Care by cleaning Always keep the part washing unit in a clean condition. -
Page 12: Troubleshooting
Disposal, Recycling of used devices 9.3 Troubleshooting ATTENTION! If any of the following errors occur, immediately stop working with the part washing unit. It can cause serious injury or damage to the tool. All repairs or replacement work must only be carried out by quali- fied and trained personnel. -
Page 13: Spare Parts
Spare parts 11 Spare parts Example The tank for the parts washer TWG 20 must be ordered. The tank has the number 1 in the spare parts drawing 1. DANGER! Risk of injury through the use of the incor- When ordering spare parts, send a copy of the spare... -
Page 14: Spare Parts Drawings
Spare parts 11.2 Spare parts drawings Spare parts drawings TWG 20 (top) and TWG 80 (bottom) TWG 20 TWG 80 Fig. 13: Spare parts drawings TWG 20 (top) und TWG 80 (bottom) TWG-Series | Version 1.01... -
Page 15: Electrical Circuit Diagram
Electrical circuit diagram Spare parts drawing TWG 150 Fig. 14: Spare parts drawing TWG 150 12 Electrical circuit diagram Fig. 15: Electrical circuit diagram TWG-Series | Version 1.01... -
Page 16: Eu Declaration Of Conformity
EU-Konformitätserklärung 13 EU Declaration of Conformity Stürmer Maschinen GmbH Manufacturer/distributing company: Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt hereby declares that the following product Unicraft® Workshop technology Product group: Part Washing Unit Type of machine: Designation of machine*: Item number: TWG 20 6220020... - Page 17 Notes 14 Notes TWG-Series | Version 1.01...
- Page 18 www.unicraft.de...