Using The Programming Buttons; Current Time/Date; Program Start Times - Weathermatic SmartWire 9600TW Owner's Manual

7.0 Programming the SL9600TW Controller
11

7.1 Using the Programming Buttons

A FLASHING DISPLAY indicates that user
choices are available. The UP and DOWN
Adjust Value buttons are used to scroll through
numeric values or to make a choice of menu
options.
NEXT and BACK Buttons:
are being programmed, the le side of the display
will indicate the zone number. The NEXT and
BACK buttons are used to scroll through the
zones. If the flashing display indicates a menu
selection rather than a numeric value, the NEXT
button will open the menu for further programming. The BACK
button will exit the menu and cause the chosen value to be
saved in memory.
RAPID ADVANCE: While programming, holding down the UP
or DOWN button will cause the flashing display value to rapidly
advance. Rapid advance can also be used with the NEXT and
BACK buttons to rapidly advance through zones.
MENUS WITHIN MENUS: In cases where there are menus within
menus, each press of the BACK button will return to the next
higher menu until the top level menu of the dial position is
reached.
A VALUE CHANGE will be entered in memory any time you (1)
move to a different menu or (2) move the programming dial to a
different position.
http://support.weathermatic.com
When watering zones

7.2 Current Time/Date

Use UP and DOWN buttons to change
the flashing value for the hour.
Scrolling past 12 will automatically
change AM/PM. Remember holding
down the UP or DOWN button will
rapidly advance through the flashing
menu. (Note: For international users,
if controller is powered by 230VAC, 50 Hz AC, the display will
read in international hours rather than AM/PM.)
Use NEXT button to flash minutes. Use UP and DOWN buttons
to set minutes. Push NEXT to access calendar setting. Use
UP and DOWN buttons to set month/day/year. (Note: For
international users, the display will read day/month/year.)
Your SmartLine® controller has a 100-year calendar, so when
you have entered the correct date, the SmartLine® controller
will automatically display the correct day of the week. Your
SmartLine® controller will automatically adjust for leap years and
USA daylight savings time. See DS TIME, in Advanced Menu to
to turn the feature on/off and change the DST schedule.

7.3 Program Start Times

Set Start Time for each program to
be used (A, B, C and D). If more than
three program start times are desired,
refer to NUM STRT, in Advanced Menu.
The program will start at the time you
designate and will water all zones with
set Zone Run Times for that program.
RUN RUN
M A N UA L ZO N E M A N UA L ZO N E SYST E M O F F SYST E M O F F
B AS I C B AS I C
M A N UA L T E ST M A N UA L T E ST C U R R E N T T I M E / DAT E
M O R E / L E SS M O R E / L E S S P R O G R A M STA R T T I ME S P R O G R A M STA R T T I M E S
S O I L T Y P E S O I L T Y P E ZO N E R U N T I M E S ZO N E R U N T I M E S
P L A N T T Y P E P L A N T T Y P E DAYS TO WAT E R DAYS TO WAT E R
SPRINKLER TYPE SPRINKLER TYPE OMIT TIMES / DAYS OMIT TIMES / DAYS
ZIP CODE / LATITUDE ZIP CODE / LATITUDE SEASONAL % ADJUST SEASONAL % ADJUST
ADVANCED ADVANCED
SMART SMART
MENU MENU
RUN RUN
M A N UA L ZO N E M A N UA L ZO N E SYST E M O F F SYST E M O F F
B AS I C B AS I C
M A N UA L T E ST M A N UA L T E ST C U R R E N T T I M E / DAT E C U R R E N T T I M E / DAT E
M O R E / L E SS M O R E / L E S S P R O G R A M STA R T T I M E S
S O I L T Y P E S O I L T Y P E ZO N E R U N T I M E S ZO N E R U N T I M E S
P L A N T T Y P E P L A N T T Y P E DAYS TO WAT E R DAYS TO WAT E R
SPRINKLER TYPE SPRINKLER TYPE OMIT TIMES / DAYS OMIT TIMES / DAYS
ZIP CODE / LATITUDE ZIP CODE / LATITUDE SEASONAL % ADJUST SEASONAL % ADJUST
ADVANCED ADVANCED
SMART SMART MENU MENU