Eight channel video receive unit with bi-directional data and ethernet for a dual redundant 1550nm wavelength fibre ring - includes amg nms network management interface (12 pages)
8 channel video receive unit with up to 9 bi-directional data and audio channels and dual redundant operation - includes amg nms network management interface (16 pages)
Eight channel video receive unit with bi-directional data with dual redundant operation on a single fibre ring - includes amg nms network management interface (9 pages)
Eight channel video receive unit with ethernet and dual redundant operation on a single fibre ring - includes amg nms network management interface (6 pages)
8 channel video receive unit with up to 9 bi-directional data / audio channels plus ethernet for a dual redundant fibre ring - includes amg nms network management interface (18 pages)
8 channel video receive unit with up to 9 bi-directional data and audio channels and dual redundant operation - includes amg nms network management interface (16 pages)
Single channel receive unit with bi-directional data channel for a dual redundant fibre ring - includes amg nms network management interface (11 pages)
Summary of Contents for AMG AMG3708BRN-DR-SF
Page 1
The AMG3708BRN-DR-SF is designed to plug into an AMG2009 or AMG2015 subrack, which in turn fits into a 19" rack system. It also includes an AMG Management Interface to allow Management of the system using the AMG SNMP enabled Management software.
Mounting Details ..........................14 Removal / replacement from / to the Case..................14 Safety Maintenance and Repair AMG Systems Ltd. reserves the right to make changes to this Page 2 of 16 AMG3708BRN-DR-SF Instruction document without notice. The information herein is believed to Sheet D18169-01.doc...
0 & 9 duplicate data channel selections 1 & 8 respectively. i.e. setting switch to position 0 or 1 selects data channel 1 and setting switch to position 8 or 9 selects channel 8. AMG Systems Ltd. reserves the right to make changes to this Page 3 of 16 AMG3708BRN-DR-SF Instruction document without notice.
Page 4
The AMG3708BN-DR-SF or rackmount AMG3708BRN-DR-SF is designed to be connected in a ring or point to point system. In a ring system single channel data insert units can be combined to make an 8 channel data transmission system as illustrated below.
Connections......... See appropriate section for connection and configuration details For the data or audio channels to be present, appropriate data daughter boards must be fitted onto the data expansion board slots. AMG Systems Ltd. reserves the right to make changes to this Page 5 of 16 AMG3708BRN-DR-SF Instruction document without notice.
Bank B carries up to 8 channels of data / audio, the physical interface of which is determined by fitment of AMG data or audio daughter boards onto the B Channel data expansion board slots.
Data and Audio Channel Configuration The data expansion board slots are accessed by removing the AMG unit from its case. A data channel is active when a daughter board is installed in the required data channel slot. Each data interface board enables one bi-directional channel.
See Data or Audio Daughter Board Instruction Sheet for meaning of Audio/Data IN+, Audio/Data IN- Audio/Data OUT+, and Audio/Data OUT- for each data type. AMG Systems Ltd. reserves the right to make changes to this Page 8 of 16 AMG3708BRN-DR-SF Instruction document without notice.
(+V) present on OUT+ logic transitions present on OUT+ logic one (-V) present on OUT+ AMG Systems Ltd. reserves the right to make changes to this Page 9 of 16 AMG3708BRN-DR-SF Instruction document without notice. The information herein is believed to Sheet D18169-01.doc...
Page 10
> 0dBm (overload at +6dBm) audio not present or < -40dBm This represents the audio signals being received from the optical fibre. AMG Systems Ltd. reserves the right to make changes to this Page 10 of 16 AMG3708BRN-DR-SF Instruction document without notice.
Power at the receiver Closed by: Reset The Management Interface The Management Interface is fitted to AMG receivers / transmitters and is signified by a 'N' in the part number AMG Systems Ltd. reserves the right to make changes to this...
Page 12
Each management interface, thus each receiver or transmitter, has an ID number with is identified below the management port. This ID number is used by the AMG Network Management System (NMS) to identify the unit. The physical interface is a 9 way female D-type connector. It supports either RS-232 or RS-485.
On release of the alarm reset, the alarm output will remain in a closed state until the next change of state to the AMG transmit unit connected to the receiver. The alarm output may not register a change of state which happens within 5 seconds of release of the alarm reset.
There are no user serviceable parts within AMG products. See unit data sheet for full specification. In case of problem or failure, please call your local support centre or contact: AMG Systems Ltd. at 3 The Omega Centre, Stratton Business Park, Biggleswade, Beds., SG18 8QB, UK.
Page 15
This page is intentionally blank. AMG Systems Ltd. reserves the right to make changes to this Page 15 of 16 AMG3708BRN-DR-SF Instruction document without notice. The information herein is believed to Sheet D18169-01.doc be accurate. No responsibility is assumed by AMG for its use.
Page 16
This page is intentionally blank. AMG Systems Ltd. reserves the right to make changes to this Page 16 of 16 AMG3708BRN-DR-SF Instruction document without notice. The information herein is believed to Sheet D18169-01.doc be accurate. No responsibility is assumed by AMG for its use.
Need help?
Do you have a question about the AMG3708BRN-DR-SF and is the answer not in the manual?
Questions and answers