Table of Contents
Advertisement
Available languages
Available languages
FR
EN DE
ES
EN
FR
DE
ES
DE
FR
EN
ES
ES
FR
EN
DE
IT
FR
EN
DE
ES
PRObLEM
FR
EN
DE
ES
IT
Engine will not start.
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
[Make sure ignition switch
is in the RUN(I) position].
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
Engine starts but will not
accelerate properly.
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
Engine starts, then dies.
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
Engine starts but will not run
properly at high speed.
FR
EN
DE
ES
IT
Engine does not reach full speed
FR
EN
DE
ES
IT
and/or emits excessive smoke.
FR
EN
DE
ES
IT
FR
EN
DE
ES
IT
Engine starts, runs, and
accelerates but will not idle.
Chain turns at idle.
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
IT
PT
NL
SV
DA NO
TROUBLEShOOTINg
PT
NL
SV
DA NO
PT
POSSIbLE CAUSE
NL
SV
DA NO
No spark.
NL
PT
SV
DA NO
SV
PT
NL
DA NO
Engine is flooded.
DA
PT
NL
SV
NO
PT
NL
SV
DA
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
Carburettor requires "L"
(Low jet) adjustment.
PT
NL
SV
DA NO
PT
NL
SV
DA NO
Carburettor requires "L" (Low Jet) Contact an authorised service centre for
adjustment.
PT
NL
SV
DA NO
PT
NL
SV
DA NO
Carburettor requires "h"
(High jet) adjustment.
PT
NL
SV
DA NO
Lubricant/fuel mixture incorrect.
PT
NL
SV
DA NO
PT
NL
SV
Air filter dirty.
DA NO
PT
NL
SV
DA NO
Spark arrester screen dirty.
Carburettor requires "h"
(High jet) adjustment.
Carburettor requires adjustment
to idle speed.
Carburettor requires adjustment
to idle speed.
Air leak in the intake system.
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
English
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
NO
FI
HU CS RU
FI
HU CS RU
FI
HU CS RU
HU
FI
CS RU
CS
FI
HU
RU
RU
FI
HU CS
FI
HU CS
RU
FI
HU CS
RU RO
FI
HU CS
RU RO
FI
HU CS
RU RO
FI
HU CS
RU RO
FI
HU CS
RU RO
FI
HU CS
RU RO
FI
HU CS
RU RO
FI
HU CS
RU RO
46
RO PL
SL
HR ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
RO PL
SL
HR
ET
SOLUTION
RO PL
SL
HR
ET
Clean or replace spark plug. Reset spark
RO PL
SL
HR
ET
plug gap. Refer to Spark Plug Replacement
earlier in this manual.
RO PL
SL
HR
ET
With the ignition switch OFF, remove spark
plug. Move choke lever to run position
RO PL
SL
HR
ET
(pushed in completely) and pull starter cord
15 to 20 times. This will clear excess fuel from
RO PL
SL
HR
ET
engine. Clean and reinstall spark plug. Set
RO PL
SL
HR
ET
ignition switch to run ( l ) position. Push and
fully release primer bulb 10 times. Pull starter
RO PL
SL
HR
ET
three times with choke lever at run. If engine
does not start, move choke lever to FULL
RO PL
SL
HR
ET
choke and repeat normal starting procedure.
If engine still fails to start, repeat procedure
RO PL
SL
HR
ET
with a new spark plug.
RO
PL
SL
HR
ET
Contact an authorised service centre for
PL
carburettor adjustment.
SL
HR
ET
SL
PL
HR
ET
carburettor adjustment.
HR
PL
SL
ET
ET
PL
SL
HR
Contact an authorised service centre for
carburettor adjustment.
PL
SL
HR
ET
Use fresh fuel and the correct 2-cycle
PL
SL
HR
ET
lubricant mix ratio.
Clean air filter. Refer to cleaning the Air
PL
SL
HR
ET
Filter in the Maintenance section of this
PL
SL
HR
ET
manual.
Clean spark arrestor screen. Refer to
Inspecting/cleaning the Spark Arrestor
Screen in the Maintenance section of
this manual.
Contact an authorized service centre for
carburettor adjustment.
Turn idle speed screw "T" clockwise to
increase idle speed. Refer to Adjusting the
Carburettor in the Maintenance section of
this manual.
Turn idle speed screw "T" counter clockwise
to decrease speed. Refer to Adjusting the
Carburettor in the Maintenance section of
his manual.
Contact an authorised service centre for a
rebuild kit.
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LT
LV
SK BG
LV
LT
SK BG
SK
LT
LV
BG
BG
LT
LV
SK
Hide quick links:
Advertisement
Table of Contents
