Video-inserter with 2 video inputs, rear-view camera input and can control (22 pages)
Summary of Contents for r.LiNK RL3-MIB-4
Page 1
Video inserter RL3-MIB-4 Compatible with VAG infotainment systems from MIB/MIB2/MIB II construction kits - High und Standard executions Compatible with Audi vehicles with MMI ( on MIB base) Bentley vehicles with MIB with 8“ monitor Lamborghini vehicles with MIB with monitor in instrument Porsche vehicles with PCM 4.0...
Case 2Interface does not receive the reverse gear signal 2.7. Connecting video-interface and external keypad 2.8. Picture settings and guide lines 3. Interface operation 3.1. By factory infotainment button 3.2. By keypad 4. Specifications 5. FAQ – Trouble Shooting-Interface functions 6. Technical support Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Due to changes in the production of the vehicle manufacturer there’s always a possibility of incompatibility. 1.1. Delivery contents Take down the serial number of the interface and store this manual for support purposes: ____________________ Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
To delay the switch-back an additional electronic part is required. Werks- PDC Die Werks-PDC Grafik entfällt bei Anschluss des Interface. Akustische Signale sind weiterhin vorhanden. AV input signal only NTSC compatible Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Try all 6 possible combinations of Dips 6, 7 and 8 to Monitor receive the best picture (quality and size) or see chapter adjustment “Monitor adjustment (Dip 6-8)” See the following chapters for detailed information. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
The interface needs a permanent 12V source! 2.1. Place of installation The interface is supposed to be installed at a suitable location behind the vehicle`s head- unit. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Quadlock connector before finishing the Quadlock reconnection at the rear of the head-unit. Note: The according HSD connector at PCM4.0 infotainments is the green coloured one. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Connect the single, yellow wire of the 10pin power/CAN cable to +12V permanent and stabile power supply. Connect the single, black wire of the 10pin power/CAN cable to the vehicle’s negative ground. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
ACC-out (max 3A) and the purple coloured wire Manual ACC of the 12pin interface cable both have to be connected additionately to S-contact terminal 86s +12V (e.g. glove compartment illumination). Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
12pin interface cable. Connect the video RCA of the Rear-view camera to the female RCA connector “Camera IN” of the 20pin interface cable (refer also to chapter “Video signal connection of the rear-view camera”) Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
“Camera IN” while the reverse gear is engaged. Additionally, the +12V (max. 3A) power supply for the rear-view camera can be taken from the green wire of the 12pin interface cable. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Page 14
Connect the output connector (87) of the relay to the rear-view camera’s power- cable, like you did it to the green “Reverse-IN” cable before. Connect stabile and permanent +12V to the relay’s input connector (30). Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Connect the female 4pin connector of the keypad to the male 4pin connector of the 12pin interface cable. Note: Even if switching through several video sources by the keypad mightn’t be required, the invisible connection and availability is strongly recommended. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Note: If there is no communication between interface and the vehicle`s CAN-bus (several vehicles aren’t compatible), the reverse gear guide-lines can`t be shown during the vehicle’s operation, even if they once appear after having switched the system to powerless! Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
7V - 25V Stand-by power drain 12mA Power 210mA @12V Video input 0.7V - 1V Video input formats NTSC Temperature range -40°C to +85°C Dimensions video-box 119 x 24 x 114 mm (W x H x D) Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Camera input picture fluorescent light which shines Test camera under natural light outside the garage. flickers. directly into the camera. Camera input picture is Protection sticker not Remove protection sticker from lens. bluish. removed from camera lens. Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...
Please note that direct technical support is only available for products purchased directly from NavLinkz GmbH. For products bought from other sources, contact your vendor for technical support. NavLinkz GmbH distribution/tech dealer-support Eurotec-Ring 39 D-47445 Moers +49 2841 949970 Email mail@navlinkz.de 10R-03 5384 Made in China Version 14.02.2018 HW: GD(V97)/(V33) RL3-MIB-4...