Subscribe to Our Youtube Channel
Related Manuals for TriTeq MicroIQ UM
Summary of Contents for TriTeq MicroIQ UM
- Page 1 E L E C T R O N I C L O C K Operation Manual Models: UM, CM, SM FOR OFFICE FURNITURE, STORAGE CABINETS, LOCKERS, SAFES, VAULTS, SECURED ENCLOSURES...
-
Page 2: Table Of Contents
Table of Contents Table of Contents Definition of Terms ..............1 Operating the Lock ...............1 Lock Components and Features ............2 Programming Instructions ...........2 Pre-programmed Codes ..............2 Programming a New Master Code Adding a Control Key-Fob ............... Programming Access Codes ............. Available User IDs ................ -
Page 3: Definition Of Terms
Definition of Terms Definition of Terms Term Meaning Factory Code This is the preset Master Code set at the factory. 1-2-3-4-5 Master Code This is the new code you will use to permanently replace the Factory Code. User ID # This is the location or two digit memory number used to store each user’s individual Access Code. -
Page 4: Lock Components And Features
Programming Instructions Lock Components and Features: Error Green Proceed Yellow Keypad Low battery Battery holder with cover Location to Knob point the Program in locked key-fob position button Push thin front edge inward Press Here Programming Instructions Pre-programmed Codes Your keypad lock has come preprogrammed with two (2) codes: Access Code 1-1-1-1-1 to allow access to the unit before you program your own codes, and Factory Code 1-2-3-4-5 to allow you to program your own unique Master Code. -
Page 5: Programming A New Master Code
Programming Instructions Programming a New Master Code Warning: Do not set your Master Code to 1-2-3-4-5. Doing so will erase all existing Access Codes and reset User ID 1-1 to Access Code 1-1-1-1-1. If a valid Master Code is entered, the green, red, and yellow LEDs will ash. -
Page 6: Adding A Control Key-Fob
Programming Instructions Adding a Control Key-Fob A Control Key-Fob can be used insted of the keypad to open or program the lock. A Control Key-Fob can be paired to as many MicroIQ locks as desired. Note: The Factory Code should be changed to a new Master Code before proceeding with the programming... -
Page 7: Programming Access Codes
Programming Instructions Programming Your Access Codes You may program up to 25 unique Access Codes. Each of these codes is used to unlock the unit. To program a 5-digit Access Code: With the lock in either the locked or unlocked position, press and hold the Program Button (located below the #3 button) for 5 seconds. -
Page 8: Available User Ids
Programming Instructions Available User IDs Use this chart to record Access Codes for each User ID. User ID #11 is factory-set to Access Code 1-1-1-1-1, and should be reprogrammed first. (1-1-1-1-1) A total of twenty-five (25) codes can be programmed. Unlocking the Unit Warning: Three invalid attempts will cause the lock to block any other attempts for 3 minutes. -
Page 9: Deleting Access Codes
Programming Instructions Deleting Access Codes Warning: This will erase all Access Codes & reset the lock back to the 1-1-1-1-1 Access Code under User ID 1-1 when complete. It will not change the Master Code. To delete all Access Codes: With the lock in either the locked or unlocked position, press and hold the Program Button (located below the #3 button) for 5 seconds. -
Page 10: Battery Replacement
Battery Replacement Battery Replacement The keypad requires a 3v lithium CR2032 battery. When the battery is low, the yellow LED light will flash 5 times after the lock is operated operated to signify the low battery level. It should be replaced as soon as possible, to avoid being locked out if the battery is depleated. - Page 11 Battery Replacement 6. Insert a new battery into the holder. The “+” surface of the battery should be inserted into the holder against the surface marked with the “+” symbol. 7. Insert the battery holder into the lock with the holder cover in the fully open position, and with the battery holder screw flush to the bottom of the holder, until the holder is fully seated.
-
Page 12: Care And Cleaning
TriTeq Limited Warranty: TriTeq offers a one year limited warranty all products to be free from manufacturing defects in materials and workmanship. This limited warranty does not cover battery, lost combinations or damages caused by improper mounting, improper or unreasonable use. -
Page 13: Troubleshooting
Turn knob to locked position Check battery orientation TriTeq Lock and Security Phone: (847) 640-7002 701 Gullo Ave Toll Free: (888) 603-5625 Elk Grove Village, IL Email: marketing@triteqlock.com 60007 042617 - Rev. 1 © Copyright 2014 TriTeq Lock and Security. All rights reserved...
Need help?
Do you have a question about the MicroIQ UM and is the answer not in the manual?
Questions and answers