Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec TAC V+ II
Summary of Contents for Trotec TAC V+ II
- Page 1 TAC V+ II / TAC M II ORIGINAL INSTRUCTIONS HIGH-PERFORMANCE AIR PURIFIER...
-
Page 2: Table Of Contents
Information marked with this symbol helps you to carry out your tasks quickly and safely. Follow the manual Information marked with this symbol indicates that the instructions must be observed. high-performance air purifier TAC V+ II / TAC M II... -
Page 3: Safety
• Do not move the device when switched on. • Never insert any objects or limbs into the device. • Do not cover the device during operation. • Do not sit on the device. high-performance air purifier TAC V+ II / TAC M II... - Page 4 They are allowed to operate and transport the device and perform simple maintenance activities (cleaning the housing, cleaning the fan). The device is to be maintained and looked after by instructed personnel. high-performance air purifier TAC V+ II / TAC M II...
-
Page 5: Information About The Device
This allows the filter to "regenerate" to 100 %. This way, the device significantly reduces the airborne risk of infection in highly frequented public zones and guarantees dust- free working conditions in contaminated working zones. Device depiction high-performance air purifier TAC V+ II / TAC M II... -
Page 6: Transport And Storage
• Make sure that no curtains or other objects interfere with contact the customer service. the air flow. • Have the device checked once a year by an electrically skilled person at any rate. high-performance air purifier TAC V+ II / TAC M II... -
Page 7: Operation
• Flashes yellow filter change required • Flashes green during rundown 13 USB interface with Update of the control software via locking cap USB flash drive with application software high-performance air purifier TAC V+ II / TAC M II... - Page 8 Der Bildschirm ist gesperrt 3. Use the arrow buttons to select the desired language. L´écran est verrouillé 4. Confirm the language selection by pressing the Confirm button. high-performance air purifier TAC V+ II / TAC M II...
- Page 9 ð Screen lock on: The screen lock is activated. ð Automatic restart : The device will start in the last set mode. 3. Press the Back button to return to the main menu. high-performance air purifier TAC V+ II / TAC M II...
- Page 10 HEPA filter 21.0 °C 12 min 21.0 °C SupplyTemp Duration 12 min SupplyTemp Duration 600 m /h 600 m /h TAC V+ Silent Boost 16:09 TAC V+ 16:09 Silent Boost high-performance air purifier TAC V+ II / TAC M II...
- Page 11 ð Once the device is switched on, the timer starts running Setpoint Fan speed and will switch off the device after the set time has been expired. back 1000 m /h high-performance air purifier TAC V+ II / TAC M II...
- Page 12 13. Press the Auto button in the main menu to activate the current switching time. ð The On and Off buttons will remain active. Main menu auto Setpoint configuration back high-performance air purifier TAC V+ II / TAC M II...
- Page 13 2. Remove the mains plug from the mains socket. regeneration. 3. Clean the device according to the Maintenance chapter. Warning 4. Store the device according to the Storage chapter. Do not switch off the device during filter regeneration! high-performance air purifier TAC V+ II / TAC M II...
-
Page 14: Available Accessories
All odours produced here are harmless to health and result from the thermal treatment to regenerate the filter. high-performance air purifier TAC V+ II / TAC M II... -
Page 15: Maintenance
10 seconds. Switch the device back on. Overheating pro- The device is Disconnect the tection motor overheating device from the mains and allow it to cool down. high-performance air purifier TAC V+ II / TAC M II... - Page 16 12. Date: ........... Signature: ........Signature: ......... Signature: ......... Signature: ......... 13. Date: ......... 14. Date: .......... 15. Date: ........... 16. Date: ........... Signature: ........Signature: ......... Signature: ......... Signature: ......... high-performance air purifier TAC V+ II / TAC M II...
- Page 17 1. Using a screwdriver, remove the protective caps of the 4 screws from the top of the device. 2. Remove all 4 screws. 3. Take off the blowing-out tower (1) from the device and carefully put aside. high-performance air purifier TAC V+ II / TAC M II...
- Page 18 Then twist off the protective cap and press the fusing into the device until it locks into place. III. 3. Insert the new air filter into the device. high-performance air purifier TAC V+ II / TAC M II...
-
Page 19: Technical Annex
(H14 or H13) Prefilter for air filter F7 (EN 779:2002), ePM10 85 % (ISO 16890) F7 (EN 779:2002), ePM10 85 % (ISO 16890) High-temperature particulate air filter TROTEC HEPA H14 Heat Resistant (EN 1822) TROTEC HEPA H14 Heat Resistant (EN 1822) Mains connection 220-240 V, 50 / 60 Hz 220-240 V, 50 / 60 Hz... - Page 20 Circuit diagram high-performance air purifier TAC V+ II / TAC M II...
- Page 21 TAC V+ II / TAC M II...
- Page 22 Hexagon socket countersunk screw (DIN 7991 M 3x6 Filter case (T0001567) Hexagon nut (DIN 934 M5 VZ) Insulation top part (T0001358) Cylinder Allen screw (DIN 912 M4x10 VZ) Heater (T0001348) Serrated lock washer (Ø5.3 x Ø10 x 0.6) high-performance air purifier TAC V+ II / TAC M II...
- Page 23 Washer (DIN 125 – A Ø5.3xØ10x1 VZ) Pressure sensor (SPS-G-2KO) Screw (Liko cross, DIN7380-1 M3x6 VZ) USB Socket (USB Go. Ex. 30cm A-W to A-M) Washer (DIN 125 – A Ø4.3xØ9x0.8 VZ) End plate (FAP 2.5/4A YE) high-performance air purifier TAC V+ II / TAC M II...
- Page 24 Protective cap (M10 SW17 plastics, black) Hexagon nut (DIN 934 M5 VZ) Washer (Ø10.3xØ15x3 white) Protective plate (protective plate) Hexagon screw (DIN 931 M10x220 VZ) Air flap cover (air flap cover) high-performance air purifier TAC V+ II / TAC M II...
- Page 25 Washer (DIN 125 – A Ø4.3xØ9x0.8 VZ) Serrated lock washer (Ø4.3xØ8x0.5 VZ) Heating cover (T0001349) Cylinder Allen screw (DIN 912 M4x8 VZ) Clamping bridge (Clamping bridge) Hexagon nut (DIN 934 M4 VZ) Sealing plug (Ø25.5xØ19xØ16x1.5x7, black) high-performance air purifier TAC V+ II / TAC M II...
- Page 26 Wheel (plain bearing wheel Ø200/50, wheel solid rubber grey, Screw (Liko cross, DIN7985 M8x16 VZ, black) 80kg) Saddle feet (Ø20-22, length 29mm, width 25.5mm pin Ø5.7, Cylinder Allen screw (DIN 912 M5x10 VZ) black) high-performance air purifier TAC V+ II / TAC M II...
- Page 27 Spare part Spare part Bottom housing (T0000665) Allen screw (Liko DIN7380-1 M6x12 VZ, black) Upper housing (T0000746) Detent-edged washer (Ø6 x Ø12.2 x 1.2 VZ) Cover for maintenance work (T0000711) high-performance air purifier TAC V+ II / TAC M II...
- Page 28 Self-adhesive needle felt (25x1mm L=2920mm) Cylinder Allen screw (DIN 912 M5x10 VZ) Detent-edged washer (Ø5.1 x Ø10.2 x 1 VZ) Connecting plate heating mantle (T0001346) Hexagon nut (self-locking, DIN 985 – M5 VZ) high-performance air purifier TAC V+ II / TAC M II...
- Page 29 Detent-edged washer (Ø5.1 x Ø10.2 x 1 VZ) Double hose connector (T0000370) Washer (DIN 125 – A Ø5.3xØ10x1 VZ) Closure plug (retaining bolt M5) Insulation lower part (0001364) Hexagon nut (DIN 934 M5 VZ) high-performance air purifier TAC V+ II / TAC M II...
- Page 30 Spare part Spare part Fan (fan TAC V+) Protective grid (bolt circle 206.6 or 226.6mm hole 5.4mm, black plastic) Hexagon screw (DIN 933 M10x25 VZ) high-performance air purifier TAC V+ II / TAC M II...
-
Page 31: Disposal
• EN ISO 13857:2008 • EN ISO 14118:2018 • EN 55011:2009 • EN 60204-1:2018 • EN 60335-1:2012 + A13:2017 • EN 60335-2-30:2009 + A11:2012 • EN 60335-2-65:2003 • EN 61000-6-1:2007 • EN 61000-6-3:2007+A11:2011+AC:2012 high-performance air purifier TAC V+ II / TAC M II... - Page 32 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...
Need help?
Do you have a question about the TAC V+ II and is the answer not in the manual?
Questions and answers