Troubleshooting - Casio 5652 Operation Manual

Watch Operation Guide 5652

Troubleshooting

Signal Reception (Time
Calibration Signal)
Q1
The watch cannot perform a receive
operation.
Is the watch's battery charged?
Signal reception is not possible while
battery power is low. Keep the watch
exposed to light until it recharges
sufficiently.
Solar Charging
l
Is the watch in the Timekeeping Mode?
Time signal receive is performed only
while the watch is in the Timekeeping
Mode. Return to the Timekeeping Mode.
Navigating Between Modes
l
Is auto time adjustment enabled?
Time signals cannot be received while
auto time adjustment is disabled. Enable
auto time adjustment to perform receive
operations.
Using OCEANUS Connected to
l
Configure Settings
Using Watch Operations to Configure
l
Settings
Is your Home City setting correct for your
location?
The watch will not indicate the correct time
if the Home City setting is wrong. Change
your Home City setting so it correctly
reflects your location.
Setting a Home City
l
After checking the above, the watch still
cannot perform a receive operation.
Time calibration signal reception is not
possible under the conditions described
below.
When watch is at Level 2 power saving
●
When the crown is pulled out
●
If successful reception is not possible for
some reason, you can adjust the time and
day settings manually.
Q2
The signal receive operation always
fails.
Is the watch in a location that is appropriate
for signal reception?
Check your surroundings and move the
watch to a location where signal reception
is better.
Appropriate Signal Reception Location
l
Did you avoid touching the watch while the
receive operation was in progress?
Minimize movement of the watch and do
not perform any watch operation while a
receive operation is in progress.
Is the signal transmitter in your area
transmitting a signal?
The transmitter of the time calibration may
not be transmitting a signal.
Try again later.
Q3
Signal reception should have been
successful, but the watch's time and/
or day is wrong.
Is the indicated time off by one hour or by
30 minutes?
The watch may be using the wrong time
offset. Correctly specify the time zone
where you are using the watch.
Setting a Home City
l
Is the indicated hour and/or minute wrong?
The hour hand and/or minute hand may
be out of alignment. Perform the
procedure under "Adjusting Hand and
Day Indicator Alignment" to auto adjust
hour and minute hand alignment.
Adjusting Hand and Day Indicator
l
Alignment
Is the indicated day of the week wrong?
The day of the week hand (mode hand)
may be out of alignment. Perform the
procedure under "Adjusting Hand and
Day Indicator Alignment" to adjust mode
hand alignment.
Adjusting Hand and Day Indicator
l
Alignment
Is the World Time incorrect?
The World Time hands (small hour hand,
small minute hand) may be out of
alignment. Perform the procedure under
"Adjusting Hand and Day Indicator
Alignment" to adjust small hour hand and
small minute hand alignment.
Adjusting Hand and Day Indicator
l
Alignment
After checking the above, the time and/or
day settings is still wrong.
Adjust time and day settings manually.
Using Watch Operations to Adjust the
l
Time Setting
I can't pair the watch with a
phone.
Q1
I've never been able to establish a
(pairing) connection between the
watch and phone.
Are you using a supported phone model?
Check if the phone model and its
operating system are supported by the
watch.
For information about supported phone
models, visit the CASIO Website.
https://world.casio.com/os_mobile/wat/
Did you install OCEANUS Connected on
your phone?
OCEANUS Connected needs to be
installed on your phone in order to
connect with the watch.
Install the required app on your
l A
phone.
Are your phone's Bluetooth settings
configured correctly?
Configure the phone's Bluetooth settings.
For details about setting procedures, see
your phone documentation.
iPhone Users
"Settings" "Bluetooth"
n n
●
"Settings" "Privacy"
n n
●
Sharing" "OCEANUS Connected"
n
On
Android Users
Enable Bluetooth.
●
Other than the above.
Some phones need to have BT Smart
disabled to use OCEANUS Connected.
For details about setting procedures, see
your phone documentation.
On the Home Screen, tap: "Menu"
"Settings" "Bluetooth"
n n
"BT Smart settings" "Disable".
n
On
"Bluetooth
n
n
"Menu"
n
17