Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for RADWAG TMC 0,3/0,6 KTPS/H1
Summary of Contents for RADWAG TMC 0,3/0,6 KTPS/H1
- Page 1 KTI-07-01/05/06/A Control of packed goods - net version Scales with TMC Terminal MANUFACTURER OF ELECTRONIC WEIGHING INSTRUMENTS RADWAG 26 – 600 Bracka 28 Street, POLAND Radom, tel.+48483848 800, tel/fax +4848 385 00 10, Sales departament +4848 366 80 06 www.radwag.com...
- Page 2 MAY 2006 - 2 -...
-
Page 3: Table Of Contents
Table of contents 1. GETTING STARTED .................... 4 2. KEYBOARD ......................5 2.1. Scale part ...................... 6 2.2. LEDs over the display ................... 6 2.3. Alphanumeric keyboard ................6 2.4. Functions of keys ..................7 3. CONNECTING EXTERNAL DEVICES..............7 4. -
Page 4: Getting Started
1. GETTING STARTED The scale consist of weighing platform and TMC terminal. Another solution is the possibility of connecting two platforms. General information − The intended use is to weigh goods with the possibility of tarring within the full measuring range. −... -
Page 5: Keyboard
Remarks concerning the save usage of scales 1. In case of weighing goods gathering electrostatic charge, connect the weighing platform with the terminal housing via a conducting wire, 2. Power cords should be connected to a socket with zeroing / earthing. 3. -
Page 6: Scale Part
2.1. Scale part 2.2. LEDs over the display 1 – zero indication 2 - equilibrium 3 – tare in memory 4 – second range 2.3. Alphanumeric keyboard TMC terminal keyboard is compatible with PC keybords. - 6 -... -
Page 7: Functions Of Keys
2.4. Functions of keys Selection of weighing platform Active platform number Display on/off Zeroing Inscribing tare value Printout Tarring 3. CONNECTING EXTERNAL DEVICES All external devices should be connected to the terminal before powering up. Connectors for additional devices are situated in the back side of the terminal. -
Page 8: Powering Up
4. POWERING UP Connect all weighing platforms and all other devices to the terminal and push the start button. Wait for complation of the test. The display will indicate zero. If there is no communication the following screen appears. - 8 -... - Page 9 After establishing communication following information appears on the display: Operator Product to control Describing data Menu Using F1, F2, F3, F4 set the following items: product name to be controlled Enter a product code that consists of maximum 6 digits and confirm it by pressing ENTER or press ESC to skip the new code.
- Page 10 Consider following remarks: Function Backspace Moving the cursor left Moving the cursor right Deleting a character over the cursor Inscribing codes After setting all codes press F5 – to start controlling. - 10 -...
-
Page 11: Weighing
5. WEIGHING Put a load on the scale pan. The result is ready to read after reaching equilibrium (signalling diode marked by After reading the result unload the pan. The indication returns to zero. For two range scales switching between ranges appears automatically while loading. -
Page 12: Getting Started
6. GETTING STARTED In order to adjust the scale for a specific conditions set filters to eliminate vibrations, possible shocks. There are to parameters for adjusting filtering: − FILTER It can be set as: Very fast Fast Average Slow MEDIAN FILTER This filter is intended to suppress single mechanical shocks. -
Page 13: Device Parameters - Filter
− Select the parameters’ group using arrows and press Enter. Press Esc to leave a function or to reach the higher level of the menu. 6.1. Device parameters – filter Setting parameters: − Set the cursor using arrows next to Filtr. −... -
Page 14: Device Parameters - Median Filter
6.1.1 Device parameters – median filter − Set the cursor using arrows next to Median Filter − Press − You will have a blinking cursor over the parameter value. It means that the value can be changed. Use arrow keys to change the value. - Page 15 Clock Using set the cursor next to Clock and press - 15 -...
-
Page 16: Cooperation With Computers
NOTICE: All values should be inscribed. All skipped values will have prescribed 00 value. Terminal Address 1 – the same address like in KTP NET software. This address should characterise the terminal. 7.2. Cooperation with computers List of parameters: Computer - (NONE,COM1,COM2,COM3,COM4,COM5(485)) Computer baud rate - (terminal-computer baud rate) -
Page 17: Printer
7.3. Printer Printer - (NONE,COM1,COM2,COM3,COM4,COM5(485)) Printer baud rate - (terminal-printer baud rate) 7.4. Additional Device Here you can set parameters for external devices: Bar code type - only EAN 13 possible, Start bar code - inscribe the digit which describes from which describes the position of starting character of the code for analysis, Bar code no of chars - The string(code) length from the start point set... -
Page 18: Program Parameters
7.5. Program Parameters Notice: If P40 Density in code is set to YES, the main display forth line changes as below: F4 - Dns. 8. INSCRIBING CODES Codes can be inscribed only in weighing mode (g or kg diode is lit). Code Assortment Operator... - Page 19 LCD view (e.g.): After pressing any of the function keys inscribe a valid code. The inscribed code can be associated with a name. It can be displayed provided: The terminal is connected with KTP NET 2003 software, The inscribe code is present in the database, Assortment codes can be read also using a barcode scanner.
-
Page 20: Performing Control
9. PERFORMING CONTROL 9.1. Basic conditions Before starting control you must inscribe 4 codes. This way you can identify: − Product name − Operator name − Batch quantity − Batch number or density LED display should indicate zero, otherwise press →0←. Press F1 and enter an assortment code. -
Page 21: Control With Average Tare
9.2. Control with average tare − put a load on the pan, − after stabilising , press Enter − put subsequent goods from the batch and do the measurements as above, − information next to the field PUT counts measurements e.g.: 1/80; 2/80, 3/80 . -
Page 22: Control With Different Tare Values (Full/Empty)
9.4. Control with different tare values (full/empty) For this option you can weight gross value of goods and then empty packages. 9.5. Tare checking module This module can check the tare value and save it to the database on the computer level. -
Page 23: Searching Operators Or Goods
− Put subsequent packages on the scale, − After stabilising press Enter, − If the average tare is acceptable (standard deviation criterion) you will see an appropriate message − If the average tare is not acceptable (standard deviation criterion) you will see an appropriate message 9.6. -
Page 24: Operator Searching
9.6.1. Operator searching − Press User, you will see: − Enter a name or a part of it, − Press Enter, you will see the result of searching, − Select the position you want by setting the cursor next to the right name using arrow keys, −... -
Page 25: Searching The Assortment Database
9.6.2. Searching the assortment database − press Assort., you will see − press F1, to search the name − inscribe a name or a part of it and press Enter, − select the position you want by setting the cursor next to the right name using arrow keys, −... -
Page 26: Technical Parameters
10. TECHNICAL PARAMETERS Type 0,3/0,6 0,6/1,5 1,5/3 KTPS/H1 KTPS /H1 KTPS /H1 KTPS/H1 Full Scale 0,6kg 1,5kg Minimum 10 g 20 g Readability 0,1/0,2 g 0,2/0,5 g 0,5/1 g 1/2 g Verification divisions 0,1/0,2 g 0,2/0,5 g 0,5/1 g 1/2 g Tare range -0,6 kg -1,5 kg... - Page 27 Type 15/30 15/30 30/60 30/60 60/150 KTPS/H2 KTPS/H3 KTPS/H3 KTPS/H4 KTPS/H4 Full scale 30kg 30kg 60kg 60kg 150kg Minimum 100 g 100 g 200 g 200 g 400 g Readability 5/10 g 5/10 g 10/20 g 10/20 g 20/50 g Verification 5/10 g 5/10 g...
- Page 28 O F E L E C T R O N I C W E I G H I N G I N S T R U M E N T S ZMP ,,RADWAG” 26 – 600 Radom, Bracka 28 Street POLAND Tel.