Replacement Parts - Weber Spirit SP-335 Owner's Manual

MAIN BURNER(S) or SIDE BURNER WILL NOT IGNITE
SYMPTOM
• Main burners or side burner do(es) not ignite when following the electronic ignition instructions in the "Operation" section of
this owner's manual.
CAUSE
There is a problem with gas flow.
There is a problem with the electronic ignition system.
Lighting Your Grill with a Match
Using a Match to Determine if there is
Gas Flow to the Burners
1) Open the barbecue lid.
2) Check that all burner control knobs are in the
off position. Check by pushing in and turning
knobs clockwise.
Note: It is important that all burner control knobs be in
the off position before you turn on the LPG cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
on position depending on your regulator/cylinder
connection.
4) Begin with burner 1, furthest to the left. Put match
in the matchstick holder and strike match. Insert lit
match down through the cooking grates, past the
FLAVORIZER BARS and next to the burner (A).
5) Push the burner control knob in and turn it anti-
clockwise to the start/high
6) Check that the burner is lit by looking through the
cooking grates and through the FLAVORIZER BARS
(B).
7) If the burner does not ignite within 4 seconds,
turn burner control knob to the off
wait five minutes to allow the gas to clear before
attempting to light the burner again. If repeated
attempts fail, follow the gas flow troubleshooting
instructions on the next page.
8) If the burner ignites, the problem lies in the ignition
system. Follow the instructions for "Checking the
Components of the Electronic Ignition System".
9) After burner 1 ignites, you can turn on burner 2
(and burner 3).
REPLACEMENT
PARTS
To obtain replacement parts,
contact the local retailer in your
area or log onto weber.com.
18
SOLUTION
If any burner does not ignite, the first step is to determine if there is gas flowing to the burner(s). To check
this, follow the instructions below for "Lighting Your Grill with a Match."
If match lighting IS NOT successful, follow the "GAS FLOW" troubleshooting suggestions on the next page.
If any burner does not ignite, the first step is to determine if there is gas flowing to the burner(s). To check this,
follow the instructions below for "Lighting Your Grill with a Match."
If match lighting IS successful, follow the instructions for "Checking the Components of the Electronic
Ignition System."
Using a Match to Determine if there is
Gas Flow to the Side Burner
1) Open the side burner lid.
2) Check that the side burner control knob is in the
off position. Check by pushing in and turning knob
clockwise. Also check that all main burner control
knobs are in the off
Note: It is important that all burner control knobs
are in the off
cylinder.
3) Turn gas supply on by turning cylinder valve
anti-clockwise or by moving regulator lever to the
on position depending on your regulator/cylinder
connection.
4) Put match in the matchstick holder and strike
match. Hold lit match by the side burner (C).
5) Push the burner control knob in and turn it anti-
clockwise to the start/high
6) Check that the side burner is lit. The side burner
position.
flame may be difficult to see on a bright sunny day.
7) If the side burner does not ignite within 4 seconds,
turn side burner control knob to the off
and wait five minutes to allow the gas to clear
before attempting to light the burner again.
If repeated attempts fail, follow the gas flow
position and
troubleshooting instructions on the next page.
8) If the burner ignites, follow the instructions for
"Checking the Components of the Electronic Ignition
System".
position.
position before turning on the LPG
position.
position
A
B
C