Maintenance And Storage - YATO YT-30432 Original Instructions Manual

Multi line green laser instrument

Table of Contents

Available languages

Charging the rechargeable battery (VI)

In order to charge the rechargeable battery, remove it from the battery compartment. Connect the rechargeable battery charging

cable adapter to the power supply plug, then connect the rechargeable battery to the adapter plug, and connect the power supply

housing to the mains. The power supply housing is equipped with an LED. The red colour indicates charging, the green colour

indicates that the rechargeable battery is charged.

Warning! Disconnect the rechargeable battery from the power supply immediately after charging is complete. Leaving the re-

chargeable battery connected to the power supply for a long time will cause irreparable damage to the rechargeable battery.

Safety recommendations for battery loading

Attention! Before loading may start make sure the body of the charger, the cable and the plug are not broken or damaged. It

is prohibited to use a damaged loading dock and charger! For the purpose of loading batteries only the charging dock and the

charger provided may be used. Using another charger may be a cause of ﬁ re or damage the tool. Batteries may be charged only

in a dry room, protected from unauthorised persons, particularly children. Do not use the charging dock and the charger without

permanent supervision of an adult! If it is necessary to leave the room where loading is taking place, it is required to disconnect the

charger from the mains, removing the charger from the mains socket. In case when smoke comes out of the charger, or a strange

smell is emitted, etc., it is required to immediately remove the plug of the charger from the mains socket! The drill and automatic

return screwdriver is provided with an unloaded battery, so before work may commence, it is required to charge it following the

procedure below, using the charger and charging dock provided. Li-ION batteries do not show the so called "memory eﬀ ect", so

it is allowed to charge them at any moment. However, it is recommended to discharge them during normal work, and then load

them to their full capacity. If due to the nature of the task it is not possible to do so each time, then it is required to do it at least

from time to time. Under no circumstances is it allowed to discharge the batteries short-circuiting the electrodes, since this would

cause irreversible damage! It is also prohibited to check the load of the batteries, short-circuiting the electrodes for sparking.

Storage of the battery

In order to prolong the life of the battery, it is required to provide adequate storage conditions. The batteries can go through

approximately 500 „loading - discharging" cycles. The battery must be stored between 0 and 30°C, at the relative humidity of

50%. In order to store the battery for a prolonged period, it is required to charge it to approximately 70% of its capacity. In case of

prolonged storage, it is required to recharge the battery once a year. Do not permit excessive discharging of the battery, since this

would reduce its life and may cause irreversible damage. During storage, the battery will be gradually unloading due to leakage

conductance. The process of automatic unloading depends on the temperature of storage, since the higher the temperature, the

fastest the process. In case of incorrect storage of batteries, there is a danger of electrolyte leakage. In case of leakage, it is

required protect the leakage with neutralizing agent. In case of contact of electrolyte with the eyes, it is required to rinse the eyes

abundantly, and then immediately seek medical assistance. It is prohibited to use a tool with a damaged battery. In case the

battery is completely worn out, it is required to deposit it at a special point dedicated to disposal of such waste.

Transport of the batteries

Lithium-ion batteries are in accordance with legal regulations treated as dangerous waste. The user of the tool may transport the

tool with the battery or only batteries by land. Then no additional conditions must be complied with. In transport is realised by third

parties (for example dispatch through courier service), then it is required to proceed in accordance with regulations for transport

of dangerous materials. Before shipment, contact an authorised person.

It is prohibited to transport damaged batteries. During transport the battery must be removed from the tool, and the exposed

contacts protected, e.g. with insulating tape. Protect the batteries so that they do not move inside the package during transport. It

is also required comply with the national regulations for transport of dangerous materials.

Safety glasses

Included with the product are safety glasses which can help see the laser beam. Safety glasses do not provide protection against

laser radiation. Safety glasses do not provide protection against mechanical or thermal hazards. Safety glasses may distort col-

ours. Do not drive vehicles wearing these glasses.

Product use

If the product is used outdoors or in the presence of a strong light source such as sunlight, the working range and visibility of laser

lines may be reduced. An example of the product use is shown in ﬁ gure (VII).