Ross MB-652-DUO Installation And Cabling

Rack Mounting
-65 2-D UO
1
e | MB SD I
Br idg
ori ng
Mo nit SD I 2
IN 4
/ 3 SDI
AN AL OG 2
AE S 1
4 x Rack Screws
Keep the following in mind when installing your MB-652-DUO:
• Install the MB-652-DUO for maximum stability and adequate ventilation
• Ensure the MB-652-DUO is installed in free air space where the ambient
temperature is monitored and controlled to not exceed 40°C (104°F)
at the frame front door airflow intake
• Ensure that adequate space exists in front and behind the MB-652-DUO
and on both sides of the frame for aiflow exhaust
• The location of the MB-652-DUO should be accessible, dry, and dust-free
Specifications
SDI Inputs and Outputs
Number of Inputs 2 Number of Inputs
Number of Outputs 2 Connector Type
Connector Type 75ohm BNC Impedance
Signal Level 800mV nominal Level
Cable Equalization SD: 200m @ 270Mbps Sampling Rate
HD: 120m @ 1.5Gbps
3G: 80m @ 3Gbps
MB652DUDR-002-03
Printed in Canada.
© 2019 Ross Video Limited. Ross®, and any related marks are trademarks or registered trademarks of Ross Video Limited. All other trademarks are the property of their respective companies. PATENTS ISSUED and PENDING. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Ross Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no
responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.
MB-652-DUO Installation and Cabling
Ethernet Cabling
ME Note:
VO LU
Contact your IT Department before connecting to your
SE T
Lt/ Rt HE AD facility network to ensure that there are no conflicts.
SU M
R
L
OR
MO NIT 8
7
6
5
Note:
Configure the DIP Switches as required to establish initial
communications between the MB-652-DUO and DashBoard. The figure
below shows all DIP Switches in the default UP position.
SW1 Position
UP
UP
DOWN
DOWN
AES Input Analog Inputs
1 Number of Inputs
BNC Connector Type 3-pin terminal blocks
75ohm Max. Input Level +24dBu, +4 typical
1Vp-p typical Frequency Response +/-0.1dB 20Hz to 20kHz
32kHz to 96kHz THD 0.005% 20Hz to 20kHz
SDI
ANALOG IN AES IN
IN 2 OUT 2
IN 1 OUT 1 MONITOR GPIO
MODE ETHERNET PSU1 PSU2
Ethernet
1 2 3 4
SW1 and SW2 - Setting the IP Address
Description
SW2 Position
The IP configuration is set DashBoard. DHCP Mode is assumed
UP
until the user changes the settings in DashBoard. (default)
The MB-651 network settings are automatically assigned (DHCP
DOWN
Mode).
The MB-651 IP Address is set to 192.168.2.1 and the Subnet
UP
Mask is set to 255.255.255.0.
The MB-651 IP Address is set to 10.1.2.1 and the Subnet Mask is
DOWN
set to 255.255.255.0.
Analog Audio Monitor Output
2 Number of Outputs 2
Connector Type 3-pin terminal blocks
Reference Level -20dBFS = +4dBu
Frequency Response +/-0.5dB 20Hz-20kHz
Distortion <0.01%THD+N
(20Hz-20kHz)
Before you set up and operate your MB-652-DUO, refer to the "Important Regulatory and Safety
Notices" document that was included with your MB-652-DUO. It is also recommended to refer to
the MB-652-DUO User Manual which is available for download from our website.
CAUTION
Power Cabling
SDI
IN 2 OUT 2
IN 1 OUT 1
Note:
The MB-652-DUO powers on automatically when the power supply
is plugged in.
Video and Audio Cabling
ANLG IN
SDI
IN 2 OUT 2
IN 1 OUT 1
SDI IN SDI OUT
Note:
For a -20dBFS input, there will be a +4dBu output.
GPIO Cabling
SDI
IN 2 OUT 2
IN 1 OUT 1
Note:
Shorting the I pin to the G pin will mute the front speakers, and the
audio level on the rear monitor ports will be controlled by the front volume knob.
Physical Specifications
Clearance Side: 2.00" (50mm) Consumption
Rear: 3.00" (75mm)
Height 3.5" (8.89cm)
Width 19.00" (48.26cm)
Depth 8.5" (21.59cm)
Temperature maximum: 40°C
Cable Clamp Inserts
ANALOG IN AES IN
MONITOR GPIO
MODE
ETHERNET PSU1 PSU2
Power
AES IN
ANALOG IN AES IN
MONITOR GPIO
Monitor Ports
MODE ETHERNET PSU1 PSU2
ANALOG IN AES IN
MONITOR GPIO
MODE ETHERNET PSU1 PSU2
GPIO Port
Power
90-240VAC
50/60Hz
90W