Six-output, two-input aes/ebu digital audio distribution amplifier (11 pages)
Summary of Contents for Broadcast Tools 2x10 DA
Page 1
CHANGE WITHOUT NOTICE Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.
2x10 DA Installation and Operation Manual CONTENTS Introduction......................3 Safety Information ....................3 Who to Contact for Help ..................3 Product Overview ....................4 Features/Benefits......................4 Inspection.........................4 Installation/Operation ....................5 Power .........................5 Surge Protection....................5 UPS Standby Power System................5 LED Indicators....................6 Stereo/Monaural Jumper Settings..............6 Audio Input Gain Jumpers.................6 Audio Input Connections...................6...
INTRODUCTION CAUTION! Thank you for your purchase of the 2x10 DA Analog Stereo Distribution Amplifier, which we will refer to throughout the manual as the 2x10 DA. We are confident this Broadcast Tools® product will give you many years of dependable service. This manual is intended to give Products, as with any you all the information needed to install and operate the Broadcast Tools®...
2x10 DA Installation and Operation Manual Product Overview The 2x10 DA analog audio distribution amplifier is equipped with a stereo line level high-Z input, which accepts either a balanced (+4 dBu) or unbalanced (-10 dBV) source and has five active balanced low-Z stereo output amplifiers. The 2x10 DA is configured for stereo (2x5) operation by default but can be configured monaural (1x10) output operation via internal jumpers.
UPS Standby Power System additional information. We recommend that you connect your 2x10 DA to a UPS standby power system. A UPS helps minimize the risk to the 2x10 DA and provides power during a power outage.
Audio Input Gain Jumper Settings The input gain of the 2x10 DA is set for a +4 dBu nominal balanced input signal via internal jumpers. Jumpers JP4 and JP5 set the left channel gain, while jumpers JP6 and JP7 set the right channel gain.
If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned to Broadcast Tools in accordance with Broadcast Tools’...
Page 9
2x10 DA Installation and Operation Manual APPENDIX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 10
2x10 DA Installation and Operation Manual APPENDIX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 11
2x10 DA Installation and Operation Manual APPENDEX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 12
2x10 DA Installation and Operation Manual APPENDEX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 13
2x10 DA Installation and Operation Manual APPENDEX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 14
2x10 DA Installation and Operation Manual APPENDIX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 15
2x10 DA Installation and Operation Manual APPENDIX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 16
2x10 DA Installation and Operation Manual APPENDIX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Page 17
2x10 DA Installation and Operation Manual APPENDIX e-mail: support@broadcasttools.com voice: 360.854.9559 fax: 866.783.1742...
Need help?
Do you have a question about the 2x10 DA and is the answer not in the manual?
Questions and answers