Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CYP DCT-23
Summary of Contents for CYP DCT-23
- Page 1 DCT-23 Integrated Zone Amplifier Operation Manual Operation Manual...
- Page 3 DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document.
- Page 4 SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
-
Page 5: Table Of Contents
CONTENTS 1. Introduction ..........1 2. Applications ........... 1 3. Package Contents ........ 1 4. System Requirements ......1 5. Features ..........2 6. Operation Controls and Functions ..3 6.1 Front Panel ........3 6.2 Rear Panel .........4 6.3 Remote Control ........5 6.4 OLED Menu ........6 6.5 RS-232 Protocols .......7 6.6 RS-232 &... -
Page 6: Introduction
1. INTRODUCTION The Integrated Zone Amplifier can accept any one of analog and digital audio from 3.5Ø line in, R/L RCA, HDMI, optical and coaxial inputs and output synchronously to R/L speaker, HDMI, optical and coaxial outputs with microphone sound added. Suitable for any musical events use, sound addition, and sound amplifying. -
Page 7: Features
5. FEATURES • Supports Digital to Analog audio Conversion (DAC) and Analog to Digital audio Conversion(ADC) • Supports input sampling rate up to 96kHz, output at 48kHz and HDMI loop out • Supports video resolution from VGA~WUXGA(RB) or 480i~1080p • Supports HDMI bypass •... -
Page 8: Operation Controls And Functions
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel PUSH UPDATE CONTROL EXIT POWER Integrated Zone Amplifier MIC: Connect with microphone for input sound signal. UPDATE: Connect with USB flash driver for firmware update only. LCM: Display current input source selection and volume setting. IR Window: Accept IR signal from the remote control included in the package. -
Page 9: Rear Panel
6.2 Rear Panel CONTROL IR IN LINE IN DC 24V RS-232 OPT. COAX. SPEAKER HDMI OUT HDMI IN 1 HDMI IN 2 OPT. COAX. CONTROL: Connecting from PC/NB with RJ-45 cable for telnet control. HDMI OUT: Connect to HD TV/monitor for both audio and video display. -
Page 10: Remote Control
6.3 Remote Control MUTE POWER POWER: Press this button to switch on the MENU device or set it to standby mode. MUTE: EXIT VOL. Press this button to mute all the output sound. HDMI 1 HDMI 2 VOL.▲▼: Press these buttons to turn the output OPTICAL volume up and down. -
Page 11: Oled Menu
6.4 OLED Menu layer layer Function Select Audio in HDMI Set Display Set MIC Set line out Set IP Config Reset to Default Audio Select* HDMI1 HDMI2 Optical In Coaxial In Line In RCA (LR) In HDMI Setting* Video HDMI1 HDMI2 Audio HDMI... -
Page 12: Rs-232 Protocols
Reset to Default *Note: HDMI audio & video are tie together and when audio select HDMI, video will not be able to select differently other than the selected HDMI port. 6.5 RS-232 Protocols DCT-23 Remote Control Assignment Assignment ► ◄... -
Page 13: Rs-232 & Telnet Commands
6.6 RS-232 & Telnet Commands Command Description HELP DISPLAY LIST OF COMMANDS ALIAS FOR HELP ALIAS FOR HELP PWR 0/1 POWER CONTROL S:STATUS, 0:OFF / 1:ON SOURCE 0~5 SOURCE IN SELECTION S:STATUS, 0:HDMI 1, 1:HDMI2, 2:OPT, 3:COAX, 4:LINE IN, 5:RCA IN VOL 0~-80 OUTPUT VOLUME SETTING 0~80dB S:SHOWVOL, +:0.5dB, ++:2dB,-:-0.5dB, --:-2dB or 0~-80 dB... -
Page 14: Telnet Control
Command Description STELNETPPORT SET THE TELNET COMMUNICATION PORT(1~62235) [23] Note: All the RS-232 command will be not executed unless followed with a carriage return. All commands are case-sensitive. 6.7 Telnet Control Before attempting to use the telnet control, please ensure that both the Intergrated Zone Amplifier (via the 'CONTROL' port) and the PC/Laptop are connected to the active networks. - Page 15 Once in the command line interface (CLI) type "telnet", then the IP address and hit enter. Note: The IP address of the Intergrated Zone Amplifier can be displayed on the device's LCM monitor by entering into the Menu's IP Config. This will bring us into the device which we wish to control.
-
Page 16: Web Gui Control
6.8 Web GUI Control On a PC/Laptop that is connected to the active network as the Intergrated Zone Amplifier, open a web browser and type device's IP address on the web address entry bar. The browser will display the device's control page. -
Page 17: Connection Diagram
7. CONNECTION DIAGRAM SmartPhone DVD or Blu-ray Player Amplifier Active Speakers 60° CONTROL IR IN LINE IN DC 24V RS-232 OPT. COAX. SPEAKER HDMI OUT HDMI IN 1 HDMI IN 2 OPT. COAX. Active Speakers DVD or Blu-ray Player Active Speakers HD TV... -
Page 18: Specifications
8. SPECIFICATIONS Input port 2 x HDMI, 1 x Optical, 1 x Coaxial, 1 x 3.5Ø Line in, 1 x R/L RCA, 1 x D-Sub 9pin (RS- 232), 1 x RJ-45 (Control), 1 x IR, 1 x MIC Output port 1 x HDMI, 1 x Optical, 1 x Coaxial, 1 x R/L RCA, 1 x R/L (SPEAKER) Digital Audio Input/Output LPCM 2CH... - Page 19 Audio Specification: Input Level/ Freq Output Output Level T.H.D+N Freq Response HDMI HDMI 1 HDMI 2 OPTICAL 0dB±1dB <0.01% ±1 dBFS >80dB OPTICAL COAX COAX 0dBFS/1kHz 2.0 Vrms ±10% <0.1% ±1 dBFS >70dB HDMI Analog L/R OPTICAL 0dB±1dB <0.01% ±1 dBFS >80dB PhoneJack COAX...
- Page 20 CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw 20141017 MPM-DCT23...
Need help?
Do you have a question about the DCT-23 and is the answer not in the manual?
Questions and answers