Subscribe to Our Youtube Channel
Related Manuals for CYP CMSI-424L
Summary of Contents for CYP CMSI-424L
-
Page 1: Operation Manual
CMSI-424L HDBaseT™ 4×4 HDMI over CAT5e/6/7 Matrix with 2 Simultaneous HDMI Outputs Operation Manual Operation Manual... - Page 3 DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document.
-
Page 4: Safety Precautions
SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. -
Page 5: Table Of Contents
CONTENTS 1. Introduction ..........1 2. Applications ........... 1 3. Package Contents ........ 1 4. System Requirements ......2 5. Features ..........2 6. Operation Controls and Functions ..3 6.1 Front Panel ........3 6.2 Rear Panel .........4 6.3 Side Panel .........5 6.4 Remote Control ........5 6.5 IR Cable Pin Assignment....6 6.6 RS-232 Protocols .......6... -
Page 6: Introduction
1. INTRODUCTION The HDBaseT™ Lite 4 by 4 HDMI Matrix over CAT5e/6/7 with two additional simultaneous HDMI outputs supports the transmission of video (resolutions up to 1080p Full HD and 1920×1200@60 Hz), multi- channel digital audio and control via IR, RS-232 or WebGUI/Telnet IP from four high definition sources to four HDBaseT outputs over a single CAT5e/6/7 cable (up to 60m) for each output. -
Page 7: System Requirements
4. SYSTEM REQUIREMENTS • HDMI equipped source devices, connect with HDMI cables or DVI equipped source, connect with DVI to HDMI cables • HDMI equipped displays (TVs or monitors) or HDMI equipped AV receivers, connect with HDMI cables • Industry standard CAT5e/6/7 cables •... -
Page 8: Operation Controls And Functions
6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel POWER LOCK MENU CMSI-424L 4X4 HDMI MATRIX LCM: Displays the setting information of each input and output setting. IR Window: IR Receiver window (accepts the remote control signal of this device only). -
Page 9: Rear Panel
6.2 Rear Panel IR OUT IR IN HDMI OUT IR IN IR OUT IR IN IR OUT IR IN IR OUT IR OUT HDMI OUT CAT5e/6 OUT CAT5e/6 OUT CAT5e/6 OUT CAT5e/6 OUT IR IN SERVICE HDMI IN 1 HDMI IN 2 HDMI IN 3 HDMI IN 4 DC 24V... -
Page 10: Side Panel
ALL IR IN: Connect an IR Receiver to this IR input. Ensure that the remote being used is within the direct line-of-sight of the IR receiver. It will transmit all IR signals received from IR IN 1-8 and IR IN ALL to IR OUT 1-4 and IR ALL OUT. DC 24V: Connect the 24 V DC power supply to the unit and plug the adaptor into an AC outlet. -
Page 11: Ir Cable Pin Assignment
6.5 IR Cable Pin Assignment IR Blaster Power IR Signal IR Extender IR Signal Power Grounding 6.6 RS-232 Protocols MATRIX REMOTE CONTROL Assignment Assignment Baud Rate: 19200bps Data bit: 8 bits Parity: None Flow Control: None Stop Bit: 1... -
Page 12: Rs-232 And Telnet Commands
6.7 RS-232 and Telnet Commands COMMAND DESCRIPTION A1~A4 Set output A to input 1, 2, 3 or 4 B1~B4 Set output B to input 1, 2, 3 or 4 C1~C4 Set output C to input 1, 2, 3 or 4 D1~D4 Set output D to input 1, 2, 3 or 4 ABCD...1~ABCD...4... - Page 13 COMMAND DESCRIPTION Set the EDID mode to 1 (STD) or 2 (TV) UARTBAUD1~4 Set the UART Baud rate of output A, B, C or D to: 1=9600 bps 4=38400 bps 2=14400 bps 5=57600 bps 3=19200 bps 6=115200 bps UARTSW1~4 Set the UART routing to output A, B, C or D and allow the matrix to send RS- 232 commands to devices connected to the receivers...
-
Page 14: Rs-232 Uart Control
6.8 RS-232 UART Control Note: This command UARTSW0 allows RS-232 control of the Matrix. IR OUT HDMI OUT CAT5e/6 OUT CAT5e/6 OUT IR IN IR OUT IR IN IR OUT IR IN IR OUT IR IN IR OUT HDMI OUT CAT5e/6 OUT CAT5e/6 OUT IR IN... -
Page 15: Telnet Control
6.9 Telnet Control Before attempting to use the Telnet control, ensure that both the Matrix (via the LAN/Control port) and the PC/Laptop or control system being used are connected to the same active network. To access the Telnet control in Windows 7, click on the 'Start' menu and type 'cmd' in the Search Field then press Enter (see below for reference). - Page 16 Type 'HELP' to list the available commands (see below for reference). Type 'IPCONFIG' To show all IP configurations. To reset the IP, type 'RSTIP' and to use a set static IP, type 'SETIP'. Note: All commands will not be executed unless followed by a carriage return.
-
Page 17: Webgui Control
6.10 WebGUI Control On a PC/Laptop or control system that is connected to the same active network as the Matrix, open a web browser and type device's IP address on the web address entry bar. The browser will display the device's status, and the control and user settings pages. - Page 18 Click on the 'User Setting' tab allows you to reset the IP configuration. The system will ask for a reboot of the device every time any of the settings are changed. The IP address needed to access the WebGUI control will also need to be changed accordingly on the web address entry bar.
-
Page 19: Connection Diagram
7. CONNECTION DIAGRAM ZONE ZONE ZONE ZONE Projector Simultaneous IR Out HDMI Output (All) RS-232 CAT5e/6/7 Power Outputs Supply IR OUT IR IN IR OUT IR IN IR OUT IR IN IR OUT HDMI OUT CAT5e/6 OUT CAT5e/6 OUT IR IN IR OUT HDMI OUT CAT5e/6 OUT... -
Page 20: Specifications
8. SPECIFICATIONS 8.1 Technical Specifications Video Bandwidth 225 MHz/6.75 Gbps Input Ports 4×HDMI, 5×IR Extender, 1×Control, 1×RS- 232, 1×Mini USB-B (For firmware update only) Output Ports 4×CAT5e/6/7, 2×HDMI, 5×IR Blaster ESD Protection Human body model: ±8 kV (air-gap discharge) ±4 kV (contact discharge) Power Supply 24 V/2.7 A DC (US/EU standards, CE/FCC/ UL certified) -
Page 21: Cat5E/6/7 Cable Specifications
8.2 CAT5e/6/7 Cable Specifications LENGTH BANDWIDTH DATA RATE SUPPORTED VIDEO HD Video Up to Up to Up to 60 m 225 MHz 5.3 Gbps Up to 1080p@60 Hz/36-bit, 3D (data rate lower than 5.3 Gbps or bandwidth below 225 MHz). Ultra HD Video Up to Greater... - Page 24 CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw...
Need help?
Do you have a question about the CMSI-424L and is the answer not in the manual?
Questions and answers