Advertisement
Quick Links
CAUTION . . .
Keep
Supplement with its
Associated Manual
It is very important to keep this document
with its associated manual.
It contains information critical to the operation
of the MINI-SCREEN safety light screen
systems that are covered.
Printed in USA
MSC..-1S..E Supplement
For MINI-SCREEN Systems with EDM and Selectable Trip/Latch Output
Models
Models
Input Power
MSCA-1S2E
115V ac
MSCA-1S3E
MSCB-1S2E
230V ac
MSCB-1S3E
MSCT-1S2E
24V dc
MSCT-1S3E
Overview
The associated control boxes are a modification of the MINI-SCREEN MSC..-1 and -1T3
controllers to include Trip/Latch output select switches and the addition of a one-channel
External Device Monitoring (EDM) input.
The primary instruction manual for these control boxes is Banner p/n 39022.
The information contained in this supplement is intended either to replace or to modify some
of the material in the primary manual. It is very important to keep this document with the
primary manual. Both documents contain information critical to the operation of these MINI-
SCREEN safety light screen systems.
09/06
Safety Outputs
FSD 1 & 2, SSD: 4 amp max.
FSD 1 & 2, CNC: 6 amp max.
SSD: 4 amp max.
FSD 1 & 2, SSD: 4 amp max.
FSD 1 & 2, CNC: 6 amp max.
SSD: 4 amp max.
FSD 1 & 2, SSD: 4 amp max.
FSD 1 & 2, CNC: 6 amp max.
SSD: 4 amp max.
EDM Input
Yes
P/N 68980
Advertisement
Related Manuals for Banner MSC 1S Series
Summary of Contents for Banner MSC 1S Series
- Page 1 External Device Monitoring (EDM) input. with its associated manual. The primary instruction manual for these control boxes is Banner p/n 39022. It contains information critical to the operation The information contained in this supplement is intended either to replace or to modify some of the MINI-SCREEN safety light screen of the material in the primary manual.
- Page 2 “Key 1 / Key 2” input for approximately ½ second, and then re-open the input. The FSD outputs will close once the open-closed-open action occurs. Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980...
-
Page 3: External Device Monitoring (Edm)
The CNC Aux output is typically used for monitoring purposes and may not be suitable for safety applications. The CNC Aux output status is the opposite that of the FSD1 and FSD2 safety outputs. Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164... -
Page 4: Switch Location
(e.g., rings or guards). Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164... - Page 5 TB1. All wiring must comply with NEC and local wiring codes. Do not operate the MINI-SCREEN System without a proper earth ground connection at either of the PE/GND symbols. Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 6 Never install arc suppressors directly across the output contacts of any safeguarding device. Figure 23 Replacement Figure 23a(s). Generic Machine Interface, MINI-SCREEN MSC..-1S2E Systems with the MSA-RM-1 relay pack Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 7 Figure 23 Replacement Figure 23b(s). Generic MaAchine Interface, MINI-SCREEN MSC..-1T3E Systems with the MSA-RM-2 relay pack Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 8 3..(s) Accessory Connections at Terminal Strip TB2 NOTE: The “Remote Test Input” has been replaced by the External Device Monitoring input. See Section 2.8 of the primary manual and Section 2.8(s). Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 9 If the MINI-SCREEN can not be reset and the “E” error code is still displayed, replace the controller card or see Section 5.3 of the primary manual. Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 10 • All red LEDs flashing NOTE: Flashing error 4 LED indicates noisy environment. Figure 2 Replacement Figure 2(s). Interpretation of diagnostic indicator LEDs, with additional error codes Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 11 Microprocessor control module MSC..-1S2E/-1S3E MSA-RM-1 MSC..-1S2E Replacement relay module MSA-RM-2 MSC..-1S3E Replacement relay module MSA-PSA-1 Replacement power supply MSCA-1S2E/-1S3E MSA-PSB-1 Replacement power supply MSCB-1S2E/-1S3E MSA-PST-1 Replacement power supply MSCT-1S2E/-1S3E Banner Engineering Corp. • Minneapolis, MN U.S.A. P/N 68980 www.bannerengineering.com • Tel: 763.544.3164...
- Page 12 Supplement: MINI-SCREEN Models with Selectable Trip/Latch Output WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture found to be defective at the time it is returned to the factory during the warranty period. This warranty does not cover damage or liability for the improper application of Banner products.