Pump Reassembly/Installing New Seal - Pentair Teel 4RJ93 Operating Instructions & Parts Manual

Hide thumbs

Table Of Contents

Table of Contents

Teel Operating Instructions and Parts Manual

Models 4RJ93, 4RJ94 and 4RJ95

Maintenance (Continued)

10. Remove slinger from motor shaft

and inspect for damage or

abrasion.

11. Clean seal cavity in seal plate and

clean motor shaft.

PUMP REASSEMBLY/INSTALLING

NEW SEAL

1. Ceramic seat must be clean and free

of dirt, grease, dust, etc. Wet outer

edge with small amount of liquid

detergent; press ceramic seat into

Polished

surface

Rubber

surface

Figure 6

Limited Warranty

DAYTON ONE-YEAR LIMITED WARRANTY. Teel

(Dayton) to the original user against defects in workmanship or materials under normal use for one year after date of purchase. Any part which is determined

to be defective in material or workmanship and returned to an authorized service location, as Dayton designates, shipping costs prepaid, will be, as the

exclusive remedy, repaired or replaced at Dayton's option. For limited warranty claim procedures, see PROMPT DISPOSITION below. This limited warranty gives

purchasers specific legal rights which vary from jurisdiction to jurisdiction.

LIMITATION OF LIABILITY. To the extent allowable under applicable law, Dayton's liability for consequential and incidental damages is expressly disclaimed.

Dayton's liability in all events is limited to and shall not exceed the purchase price paid.

WARRANTY DISCLAIMER. Dayton has made a diligent effort to provide product information and illustrate the products in this literature accurately; however,

such information and illustrations are for the sole purpose of identification, and do not express or imply a warranty that the products are MERCHANTABLE, or

FIT FOR A PARTICULAR PURPOSE, or that the products will necessarily conform to the illustrations or descriptions.

Except as provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in the "LIMITED WARRANTY" above is made or

authorized by Dayton.

PRODUCT SUITABILITY. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of products for certain purposes,

which may vary from those in neighboring areas. While Dayton attempts to assure that its products comply with such codes, it cannot guarantee compliance,

and cannot be responsible for how the product is installed or used. Before purchase and use of a product, review the product applications, and all applicable

national and local codes and regulations, and be sure that the product, installation, and use will comply with them.

Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not apply to you; (b) also, some jurisdictions do not allow a limitation on how long an implied

warranty lasts, consequently the above limitation may not apply to you; and (c) by law, during the period of this Limited Warranty, any implied warranties of

implied merchantability or fitness for a particular purpose applicable to consumer products purchased by consumers, may not be excluded or otherwise

disclaimed.

PROMPT DISPOSITION. Dayton will make a good faith effort for prompt correction or other adjustment with respect to any product which proves to be

defective within limited warranty. For any product believed to be defective within limited warranty, first write or call dealer from whom the product was

purchased. Dealer will give additional directions. If unable to resolve satisfactorily, write to Dayton at address below, giving dealer's name, address, date, and

number of dealer's invoice, and describing the nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was damaged

in transit to you, file claim with carrier.

Manufactured for Dayton Electric Mfg. Co., 5959 W. Howard St., Niles, Illinois 60714 U.S.A.

seal plate cavity firmly and squarely

with finger pressure (See Figure 6).

2. If ceramic seat will not locate

properly, remove it, place face up

on bench and reclean cavity.

Ceramic seat should now locate.

3. If seat still will not locate properly,

place a cardboard washer over the

polished face and use a piece of

3/4" (19mm) standard pipe for