Crown CT63006 Manual Original page 9

Recommendations on the power tool op-
eration
General recommendations (see fig. 1-2, 4-6)
• Select and set the nozzle depending on the type of
work to be done (see fig. 1-2, 4-6).
• The crevice nozzle with the brush 7 is designed for
effective suction of dust or dry fine debris on various
surfaces, as well as in confined spaces.
• To vacuum up dust or dry fine debris:
• use the nozzle 7 with the brush 9 slid backwards
(see fig. 1.1, 4) on a smooth surface (e.g. salt scat-
tered on a table);
• use the nozzle 7 with the brush 9 slid forward (see
fig. 1.2, 5.1) on hairy surfaces (e.g. crumbs on furni-
ture upholstery or carpet);
• use the nozzle 7 without the brush 9 (see
fig. 1.3, 5.2) in confined spaces (e.g. between cush-
ions of cushioned furniture)�
• The rubber nozzle 6 is designed for effective suction
of liquid from various surfaces (see fig. 6.1). Atten-
tion: vacuum up only small amounts of liquid (e.g.
a drink spilled on the table).
• Turn on the power tool, vacuum up dust, small dry
debris or liquids�
• Attention: vacuum up dry debris and liquids
separately. Empty the dust-collecting container 1,
as described below, before vacuuming up other
types of debris�
• If you notice a decrease in performance during op-
eration, check the dust-collecting container 1, empty it
as described below, if necessary�
• When you have finished working, turn off the power
tool�
• If you have been working in the liquid suction mode,
drain the liquid from the dust-collecting container 1 im-
mediately after finishing work as described below.
Power tool maintenance / preventive
measures
Battery maintenance instruction
• Charge timely before the battery is completely ex-
hausted� Stop operation in low power and charge it
immediately�
• Do not overcharge when the battery is full, otherwise
it will shorten the life time�
• Charge battery in the room temperature of 10°C
to 40°C (50°F to 104°F)�
• Charge battery every 6 months without operation for
a long time�
• Decline of production or a significantly shorter runt-
ime of the power tool after charging indicates aging of
the battery and the need for replacement� It should be
taken into account that the battery may discharge faster
if the works take place in the temperature below 0°С.
Contact the CROWN service center for battery replace-
ment�
The manufacturer reserves the possibility to introduce changes.
Emptying the dust-collecting container (see fig. 7)
Monitor the dust-collecting container 1
filling, and empty it promptly according
to safety precautions described above.
• Turn off the power tool�
• Press the locking button 2 and remove the dust-
collecting container 1 (see fig. 7.1).
• Remove the filter holder 12 and the filter 13 from the
dust-collecting container 1 (see fig. 7.2).
• Observing safety regulations, dump the dust-collect-
ing container 1 contents out�
• Wash the dust-collecting container 1, the filter hold-
er 12 and the filter 13 under running water, and then
dry them�
• When all the parts are dry, reassemble them in the
reverse order�
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
flush the power tool with compressed air thought the
ventilation slots 3�
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.crown-tools.com.
Transportation of the power tools
• Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Li-Ion batteries
The contained Li-Ion batteries are subject to the Danger-
ous Goods Legislation requirements� The user can trans-
port the batteries by road without further requirements�
When being transported by third parties (e�g�: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed� For prepa-
ration of the item being shipped, consulting an expert
for hazardous material is required�
Dispatch batteries only when the housing is undam-
aged� Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move around
in the packaging� Please also observe possibly more
detailed national regulations�
Environmental protection
Recycle raw materials instead of dispos-
ing as waste.
Power tool, accessories and packaging should
be sorted for environment-friendly recycling�
The plastic components are labelled for categorized
recycling�
These instructions are printed on recycled paper man-
ufactured without chlorine�
English
9