Table of Contents
Advertisement
NOTE: Hooks will not rotate until they are fully extended.
nap
■
Hang the fan from a sturdy location.
ning
Mounting the fan to 2x wood material using the hooks:
■
Pull the hooks completely out of their slots and rotate them
upward 180 degrees.
NOTE: Hooks will not rotate until they are fully extended.
■
Put the wider side of the 2x wood material on the clamping
surface of the fan legs. The edge of the wood should rest
ur
against the front surface of the legs.
ts,
■
Rotate the hooks down 180 degrees to clamp the fan to the 2x
or
wood material.
hat
■
To remove the fan from the 2x wood material, rotate the hooks
180 degrees to the upward position.
tely
Mounting the fan to rods using the rod pockets:
eep
■
The fan can be mounted to rods, tubes, or rebar using the
tery
pockets on the base of the fan.
NOTE: The mounting posts must have a diameter between 13
and 22.6 mm.
Mounting the fan to a 2x4 using the 2x4 recess:
■
Place the fan onto a 2x4. Make sure the wood is seated
completely inside the 2x4 recess.
as
■
Secure the fan to the wood using bungee cords or tie downs.
ADJUSTING THE HEAD
e.
See Figure 4.
ning
The portable fan head can be rotated 240 degrees. To switch head
positions, adjust head to desired position.
BATTERIES
tery
Battery packs which have not been used for some time should be
recharged before use.
and
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
wise
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
he
from the charger once it is fully charged.
not
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C
and away from moisture.
• Store the battery packs in a 30% - 50% charged condition.
• Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
the
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
ntal
■
The user can transport the batteries by road without further
ents
requirements.
■
Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately.
ew.
trained persons and the process has to be accompanied by
corresponding experts.
row
When transporting batteries:
■
Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
m as
■
Ensure that battery pack is secured against movement within
packaging.
■
Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life. Under extreme stress the
battery electronics switch off the machine automatically. To restart,
switch the machine off and then on again. If the machine does not
start up again, the battery pack may have discharged completely. In
this case it must be recharged in the battery charger.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been described,
please contact one of our AEG service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at:
Techtronic Industries Australia Pty Ltd
PO Box 1065
Mount Waverley VIC 3149
Tel. no. 1300 234 797
Australia
Techtronic Industries N.Z. Limited
PO Box 12-806
Penrose AUCKLAND 1642
Tel. no. 0800 234 797(0800 AEGPWR)
New Zealand
SYMBOLS
Safety alert
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Please read the instructions carefully before
starting the machine.
The product can be used in a tropical climate.
Class II, double insulated
For indoor use only.
Do not dispose of electric tools together with
household waste material. Electric tools and
electronic equipment that have reached the end of
their life must be collected separately and returned
to an environmentally compatible recycling facility.
7
7
Advertisement
Table of Contents
