Advertisement
Available languages
Available languages
ENG LIS H
SAVE THESE INSTRUCTIONS FOR FUTURE USE
DATE CODE POSITION (FIG.1)
The date code (x), which also includes the year of
manufacture, is printed into the housing.
Example:
2014 XX XX
Year of Manufacture
Package Contents
The package contains:
1 die grinder
2 wrenches
1 instruction manual
Motor
Be sure your power supply agrees with the nameplate
marking. Voltage decrease of more than 10% will
cause loss of power and overheating. All D
tools are factory tested; if this tool does not operate,
check the power supply.
COMPONENTS (Figure 1)
WARNING: Never modify the power tool or any
part of it. Damage or personal injury could result.
A. spindle
B. Nut
C. Small spanner(13mm)
D. Large spanner(17mm)
E. Switch (DWE886S)
F
. Switch (DWE886T)
G1. Lock-Off button (DWE886P)
G2. Paddle switch (DWE886P)
INTENDED USE
The DWE886S, DWE886T&DWE886P die grinders have
been designed for professional grinding.
use under wet conditions or in presence of flammable
liquids or gases.
These die grinders are professional power tools.
DO NOT
let children come into contact with the
tool. Supervision is required when inexperienced
operators use this tool.
Switches
WARNING: Before connecting the tool to a
power source depress and release the switch
once without depressing the lock-on button
to ensure that the switch is off. Depress
and release the switch as described above
after any interruption in power supply to
the tool, such as the activation of a ground
6
WARNING: Grasp tool firmly with both hands
WARNING: To reduce unexpected tool
WALT
E
SLIDER SWITCH DWE886S(FIG. 1)
WARNING: Before connecting the tool to a power
source, please check and ensure the switch is off.
Switch it off as described above after any
interruption in power supply to the tool, such as
the activation of a ground fault interrupter,
throwing of a circuit breaker, accidental unplug-
ging, or power failure. If the switch is on, the tool
will start unexpectedly when it is reconnected.
If the slider switch is locked on when the power is
connected, the tool will start unexpectedly. To start
the tool, slide the slider switch (E) toward the front of
the tool. To stop the tool, release the slider switch.
For continuous operation, slide the switch toward
the front of the tool and press the forward part of
the switch inward. To stop the tool while operating
in continuous mode, press the rear part of the slider
switch and release.
TOGGLE SWITCH DWE886T (FIG. 1)
DO NOT
WARNING: Before using the tool, check that the
handle is tightened securely.
To turn on the tool, lift up the button(F) to ''1"
position, to turn off the tool, push the toggle switch
Button(F) to "0" position.
WARNING: Do not switch the tool on or off when
under load.
fault interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure. If
the switch is locked on, the tool will start
unexpectedly when it is reconnected.
to maintain control of the tool at start up and
during use and until the wheel or accessory
stops rotating. Make sure the wheel has
c
o
m
e
o t
a
c
o
m
p
e l
e t
s
tool down.
movement, do not switch the tool on or off
while under load conditions. Allow the grinder
to run up to full speed before touching the
work surface. Lift the tool from the surface
before turning the tool off.
WARNING: Allow the tool to reach full speed
before touching tool to the work surface. Lift
the tool from the work surface before turning
the tool off.
WARNING: Do not switch the tool on
or off when under load.
o t
p
b
f e
r o
l e
y a
n i
g
t
e h
Advertisement
