Table of Contents
Advertisement
a SWITCHER (switcher I/O) A and B connectors
(MDR 68-pin) (MKE-9020M)
Connect with the supplied special cable to the DME 1A
and 1B connectors of the MVS-8000 Multi Format
Switcher Processor.
Each connector handles two channels of video signal input
and output. Therefore, when this unit is configured for one
or two channels (with one or two MKE-9040M boards
installed), you do not need to connect the SWITCHER B
connector.
If you are connecting a second MVE-8000 Multi Format
DME Processor to the MVS-8000, connect the
SWITCHER A and B connectors on the second processor
to the DME 2A and DME 2B connectors on the MVS-
8000.
a V, K IN/OUT (video and key input and output)
connectors (BNC type) (MKE-9021M)
Used for SDI interface input and output of video signals
between this unit and the switcher or external video
devices.
b - AC IN (AC power input) A and B connectors (3-
pin)
Connect to 100 to 240 V AC power supply with the
optional AC power cord.
c U (signal ground) terminal
Connect to the system ground.
d GPI (General Purpose Interface) and GPI 2
connectors (D-sub, 25-pin)
Connect to external devices for input and output of trigger
signals. Up to sixteen inputs and sixteen outputs are
possible, with input and output conditions set on the center
control panel.
e MONI OUT (monitor output) connectors (BNC
type)
Used to output system channel video keys and graphics to
a monitor.
f REMOTE 1 to 4 connectors (D-sub 9-pin, RS-
422A)
Connect to control this unit from a BVE-9100 or other
editing control system.
g CONTROL connector (RJ-45)
Connect to an Ethernet switch
The MVS-8000 Multi Format Switcher Processor and the
MVS-8000 system's center control panel are connected in
the same way to the Ethernet switch to form a network for
exchange of signals between the devices.
This network is used primarily to control the various
devices from the center control panel.
* Ethernet is a trademark of XEROX Corporation.
For information about Ethernet switches that can be used in an MVS
system, contact your Sony service representative.
*
.
For detailed information about setting up the Ethernet
switch, refer to the documentation supplied with the
switch.
For more information about Ethernet switch connectors,
see "MVS-8000 System Configuration" (page 12).
Caution
When using a LAN cable: For safety, do not connect to the
connector for peripheral device wiring that might have
excessive voltage.
h DATA connector (RJ-45)
Connect to an Ethernet switch.
The MVS-8000 Multi Format Switcher Processor and the
MVS-8000 system's center control panel are connected in
the same way to the Ethernet switch to form a network for
exchange of signals between the devices.
This network is used primarily for exchange of various
types of data (key frame effects, snapshots, etc.).
Caution
When using a LAN cable: For safety, do not connect to the
connector for peripheral device wiring that might have
excessive voltage.
i REF IN (reference video signal input) connectors
(BNC type)
If you wish to synchronize this unit to an external reference
signal, input the reference signal. For an HDTV system,
input an HD tri-level sync signal, black burst signal, or
analog sync signal. For an SDTV system, input a black
burst signal or analog sync signal.
The two connectors have a loop-through configuration.
Signal input to one connector can be output from the other
connector. If you will not be using the loop-through
output, be sure to terminate the unused connector with the
supplied 75Ω terminator.
j EXT IN (external SDI video signal input)
connectors (BNC type)
Used to input external video signals for use as effect
materials.
Location and Function of Parts
11
Advertisement
Table of Contents
