1-3/8" crown carton closing stapler 5/8" and 3/4" (15mm and 18mm)
1-1/4" crown carton closing stapler 5/8" and 3/4" (15mm and 18mm) (12 pages)
Summary of Contents for Interchange CN70-15
Page 1
Operator’s Manual Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails 1-3/4" to 2-3/4" / 45 to 70mm Ask for Genuine INTERCHANGE ® HWCF Nails NOte: Please read and fully understand the instructions in this manual before operating the pneumatic power tool. Carefully read through this OPERATOR’S MANUAL to ensure efficient, safe operation.
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) Important Information WARNING: The warnings, cautions and instructions discussed in this instruction manual can not cover all possible conditions and situations that may occur . It must be understood by the operator that common sense and caution are factors which can not be built into this product, but must be supplied by the operator .
WARNING: Be sure to use only the genuine nails recommended for the CN70-15 . The use of any other nails can result in tool malfunction, leading to serious injuries . Only the nail sizes shown in the table below can be driven with this nailer .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) Safety Information Important Safety Instructions for Operating Nailers READ ALL INSTRUCTIONS OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS.
Page 7
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) 10 . STAY ALERT. Watch what you are doing . Use common sense and do not operate the nailer when you are tired . The nailer should never be used if you are under the influence of alcohol, drugs or medication that makes you drowsy .
Page 8
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) 22 . KEEP ALL SCREWS AND COVERS MOUNTED TIGHTLY IN PLACE. Keep all screws and covers tightly mounted . Check their condition periodically .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) 32 . DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE NAILER IS NOT IN USE. NEVER LEAVE A NAILER UNATTENDED WITH THE HOSE ATTACHED.
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) operating the Nailer NOtE: The information contained in this Manual is designed to assist you in the safe operation of the nailer . Some illustrations in this Manual may show details or attach- ments that are different from those on your nailer .
Filter-regulator-lubricator units should always be used . Keep the lubricator filled with INTERCHANGE pneumatic tool lubricant . If a lubricator is not available, supply 3 to 5 drops of INTERCHANGE pneumatic tool lubricant into the air plug on the tool twice a day .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) operating The Nailer DANGER: Operators and others in work area must wear safety glasses with side shields that conform to ANSI Z87 .1 specifications .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) Nail Loading OPEN THE MAGAZINE Hold door and door latch and pull up door latch . Swing door open . Swing magazine cover open .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) Testing The Nailer Before using the nailer, test it by using the check list below . If abnormal tests occur, stop using the nailer and contact an authorized service center immediately .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) Driving Depth Adjustment Dial (on some models) WARNING: Always disconnect air supply before changing the adjustment dial . ■ With air pressure set, drive nails into a piece of scrap material to determine if an adjustment is necessary .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) maintenance and Inspection Read the section titled SAFETY. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use . It is recommended that these operations should be performed by a professional technician .
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) Parts Drawing/Schematics, Parts List & Parts Kits PARTS DRAWING/SCHEmATICS FoR CN70-15 Interchange Brands Operator’s Manual...
Coil Nailer Model No. CN70-15 Item No. 65560 Drives Wire Collated Nails (1-3/4" to 2-3/4" / 45 to 70mm) PARTS LIST FoR CN70-15 ORDER NO. DESCRIPTION ORDER NO. DESCRIPTION 610570 BOLT M6X32 510320 O-RING 10X2.65 320470 SIDE PROTECTOR 510430 O-RING 20X2.65...
Piston/Driver Assembly for CN70-15 98320 CN70K3 Kit #3 Head Cap Assembly for CN70-15 98330 CN70K4 Kit #4 Trigger Valve Assembly with Trigger for CN70-15 98340 CN70K5 Kit #5 Magazine Assembly for CN70-15 98350 CN70K6 Kit #6 Guide Body Assembly for CN70-15...
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. CN70-15 Coil Nailer Interchange Brands CN70-15 Made In China Operator’s Manual (8/6/15)
Need help?
Do you have a question about the CN70-15 and is the answer not in the manual?
Questions and answers