Interchange CN80-15 Operator's Manual

Interchange CN80-15 Operator's Manual

15 coil framing nailer, industrial coil nailer.

Advertisement

Quick Links

CN80-15
15º Industrial Coil Nailer
Item No. 65565
Drives Wire Collated Nails
2" to 3-1/4" / 50 to 83mm
Ask for Genuine
INTERCHANGE
HWCF Nails
CN80F-15
15º Coil Framing Nailer
Item No. 65566
Drives Wire Collated Nails
2" to 3-1/4" / 50 to 83mm
Ask for Genuine
INTERCHANGE
HWCF Nails
NOte:
Please read and fully understand the instructions in this
manual before operating the pneumatic power tool. Carefully read
through this OPERATOR'S MANUAL to ensure efficient, safe operation. It is
recommended that the MANUAL be kept readily available as an important refer-
ence when using this tool.
Operator's Manual
15
®
®
o
Coil Nailers

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CN80-15 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Interchange CN80-15

  • Page 1 Operator’s Manual Coil Nailers CN80-15 15º Industrial Coil Nailer Item No. 65565 Drives Wire Collated Nails 2" to 3-1/4" / 50 to 83mm Ask for Genuine INTERCHANGE ® HWCF Nails CN80F-15 15º Coil Framing Nailer Item No. 65566 Drives Wire Collated Nails 2"...
  • Page 2: Table Of Contents

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Index Information . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Important Information .
  • Page 3: Important Information

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Important Information WARNING: The warnings, cautions and instructions discussed in this instruction manual can not cover all possible conditions and situations that may occur .
  • Page 4: Tool Information

    Nail Specifications WARNING: Be sure to use only the genuine nails recommended for the CN80-15 . The use of any other nails can result in tool malfunction, leading to serious injuries . Only the nail sizes shown in the table below can be driven with this nailer .
  • Page 5: Accessories

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Parts Identification ➑ ➋ ➐ ➊ Casting ➏ ➋ Cylinder Cap ➌ Safety ➍ Guide Body ➊ ➎ Magazine ➏...
  • Page 6: Safety Information

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") safety Information Important Safety Instructions for Operating Nailers READ ALL INSTRUCTIONS OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS.
  • Page 7 Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") 10 . STAY ALERT. Watch what you are doing . Use common sense and do not operate the nailer when you are tired .
  • Page 8 Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") 22 . KEEP ALL SCREWS AND COVERS MOUNTED TIGHTLY IN PLACE. Keep all screws and covers tightly mounted . Check their condition periodically .
  • Page 9: Employer's Responsibilities

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") 32 . DISCONNECT THE AIR SUPPLY AND EMPTY THE MAGAZINE WHEN THE NAILER IS NOT IN USE. NEVER LEAVE A NAILER UNATTENDED WITH THE HOSE ATTACHED.
  • Page 10: Operating The Nailer

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") operating the Nailer NOtE: The information contained in this Manual is designed to assist you in the safe operation of the nailer . Some illustrations in this Manual may show details or attach- ments that are different from those on your nailer .
  • Page 11: Lubrication

    „ Filter-regulator-lubricator units should always be used . Keep the lubricator filled with INTERCHANGE pneumatic tool lubricant . „ If a lubricator is not available, supply 3 to 5 drops of INTERCHANGE pneumatic tool lubricant into the air plug on the tool twice a day .
  • Page 12: Operating Instructions

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") operating The Nailer DANGER: Operators and others in work area must wear safety glasses with side shields that conform to ANSI Z87 .1 specifications .
  • Page 13: Nail Loading

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Nail Loading OPEN THE MAGAZINE Hold door and door latch and pull up door latch . Swing door open .
  • Page 14: Testing The Nailer

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Testing The Nailer Before using the nailer, test it by using the check list below . If abnormal tests occur, stop using the nailer and contact an authorized service center immediately .
  • Page 15: Troubleshooting

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Driving Depth Adjustment Dial WARNING: Always disconnect air supply before changing the adjustment dial . ■ With air pressure set, drive nails into a piece of scrap material to determine if an adjustment is necessary .
  • Page 16: Maintenance And Inspection

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") maintenance and Inspection Read the section titled SAFETY. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use .
  • Page 17: Parts Drawing/Schematics

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Parts Drawing/schematics, Parts List & Parts Kits PARTs DRAWING/sCHEmATICs FoR CN80-15 Interchange Brands Operator’s Manual...
  • Page 18: Parts List

    Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") PARTs LIsT FoR CN80-15 ORDER NO. DESCRIPTION ORDER NO. DESCRIPTION 610630 BOLT M8X25 (Loctite 243) 55 510430 O-RING 20X2.65...
  • Page 19: Parts Kits

    Piston/Driver Assembly for CN80-15 and CN80F-15 98560 CN80K3 Kit #3 Head Cap Assembly for CN80-15 and CN80F-15 98565 CN80K4 Kit #4 Trigger Valve Assembly with Trigger for CN80-15 and CN80F-15 98570 CN80K5 Kit #5 Magazine Assembly for CN80-15 and CN80F-15 98575 CN80K6...
  • Page 20 Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Parts Drawing/schematics, Parts List & Parts Kits PARTs DRAWING/sCHEmATICs FoR CN80F-15 Interchange Brands Operator’s Manual...
  • Page 21 Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") PARTs LIsT FoR CN80F-15 ORDER NO. DESCRIPTION ORDER NO. DESCRIPTION 610630 BOLT M8X25 120070 BODY (MAGNESIUM) 320480 EXHAUST COVER 510090 O-RING 4X1.5...
  • Page 22 Piston/Driver Assembly for CN80-15 and CN80F-15 98560 CN80K3 Kit #3 Head Cap Assembly for CN80-15 and CN80F-15 98565 CN80K4 Kit #4 Trigger Valve Assembly with Trigger for CN80-15 and CN80F-15 98570 CN80K5 Kit #5 Magazine Assembly for CN80-15 and CN80F-15 98575 CN80K6...
  • Page 23 Coil Nailer Model No. CN80-15, Item No. 65565 Model No. CN80F-15, Item No. 65566 Drives Wire Collated Nails (2" to 3-1/4") Interchange Brands Operator’s Manual...
  • Page 24: Warranty

    This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. Interchange Brands CN80-15, CN80F-15 Made In China Operator’s Manual (8/6/15)

This manual is also suitable for:

Cn80f-156556565566

Table of Contents