Panasonic AK-UC3300G Operating Instructions Manual page 61

Item
[PEAK FREQUENCY]
[V DETAIL
FREQUENCY]
[CRISP]
[DETAIL GAIN(+)]
[DETAIL GAIN(−)]
[DETAIL CLIP+]
[DETAIL CLIP−]
[DETAIL SOURCE]
[KNEE APERTURE
LEVEL]
[DETAIL KNEE]
[LEVEL DEPENDENT
SWITCH]
[LEVEL DEPENDENT]
[DARK DETAIL SWITCH] Enables/disables the function to emphasize details of dark areas.
[DARK DETAIL]
[SKIN TONE DETAIL [SKIN TONE DETAIL]
SETTING]
[SKIN GET]
[MEMORY SELECT]
[CURSOR]
[H POSITION]
[V POSITION]
[ZEBRA]
[ZEBRA EFFECT
MEMORY]
[SKIN TONE EFFECT
MEMORY]
Chapter 4 Menu Operations — Menu list
Sets the peak frequency of the horizontal detail.
[12.4MHz], [12.5MHz], [12.7MHz], [12.9MHz], [13.0MHz], [13.3MHz], [13.6MHz], [13.9MHz], [14.2MHz],
[14.6MHz], [15.0MHz], [15.5MHz], [16.1MHz], [16.7MHz], [17.3MHz], [18.3MHz], [18.6MHz], [18.8MHz],
[19.0MHz], [19.2MHz], [19.5MHz], [19.9MHz], [20.3MHz], [20.9MHz], [21.5MHz], [22.4MHz], [23.6MHz],
[25.4MHz], [28.6MHz], [37.1MHz]
• • Factory setting: [15.0MHz]
Sets the vertical detail frequency.
[00]...[31]
• • Factory setting: [10]
Sets the detail signal noise removal level.
[00]...[63]
• • Factory setting: [10]
Sets the detail level in the + (upward) direction.
[−31]...[+31]
• • Factory setting: [0]
Sets the detail level in the − (downward) direction.
[−31]...[+31]
• • Factory setting: [0]
Adjust the detail clip to reduce glare produced by an excess of details.
[00]...[63]
• • Factory setting: [0]
Adjusts the length of the undershoot of the detail edge component.
[00]...[63]
• • Factory setting: [0]
Sets the RGB signal component ratio to create the detail.
[(G+R)/2], [(G+B)/2], [(2G+B+R)/4], [(3G+R)/4], [R], [G]
• • Factory setting: [(G+R)/2]
Adjusts the knee aperture level.
This cannot be set in HDR mode.
[00]...[39]
• • Factory setting: [0]
Adjusts the detail components of knee.
[00]...[15]
• • Factory setting: [0]
Enables/disables the function to remove details of dark areas.
This cannot be set in HDR mode.
[OFF], [ON]
• • Factory setting: [OFF]
Sets the level to remove details of dark areas.
[00]...[15]
• • Factory setting: [8]
This cannot be set in HDR mode.
[OFF], [ON]
• • Factory setting: [OFF]
Sets the level to emphasize details of dark areas.
[00]...[7]
• • Factory setting: [2]
Enables/disables the skin tone detail function.
[OFF], [ON]
• • Factory setting: [OFF]
Selects whether to automatically obtain the color saturation and hue information from the cursor position.
[NO], [YES]
Selects the skin tone table of the subject to apply the skin tone table to.
[A], [B], [C]
• • Factory setting: [A]
Shows/hides the box cursor in the center of the screen.
[OFF], [ON]
• • Factory setting: [OFF]
Adjusts the horizontal position of the cursor.
[0%]...[100%] (0.25% step)
• • Factory setting: [50%]
Adjusts the vertical position of the cursor.
[0%]...[100%] (0.25% step)
• • Factory setting: [50%]
Enables/disables the zebra display.
[OFF], [ON]
• • Factory setting: [OFF]
Selects the table of the zebra display.
[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]
• • Factory setting: [A+B+C]
Selects the skin tone table used to apply the skin tone detail.
[A], [B], [C], [A+B], [A+C], [B+C], [A+B+C]
• • Factory setting: [A+B+C]
– 61 –
Description of settings