Daily Use; Functions - IKEA RENGORA Manual

Product description
2. SWITCH ON THE DISHWASHER
Open the door and press the ON/OFF button.
3. LOAD THE RACKS (see LOADING THE RACKS)
ENGLISH
4. FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
The machine will switch off automatically during certain
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
extended periods of inactivity, in order to minimise electri-
Select the most appropriate program in accordance with the
city consumption. If the crockery is only lightly soiled or
• In order to maximize dishwasher efficiency it is
type of crockery and its soiling level (see PROGRAMS
if it has been rinsed with water before being placed in the recommended to initiate the wash cycle once dishwasher
DESCRIPTION) by pressing the
is fully loaded. Loading the household dishwasher up to
dishwasher, reduce the amount of detergent used accordingly.
the capacity indicated by the manufacturer will contribute to
Select the desired options (see OPTIONS AND FUNCTIONS).
energy and water savings. Information on correct loading of
6. START
MODIFYING A RUNNING PROGRAM
tableware can be found in Loading chapter. In case of partial
Start the wash cycle by pressing START/Pause button (led
If a wrong program was selected, it is possible to change it, pro-
loading it is recommended to use dedicated wash options
is lit) and closing the door within 4 sec. When the program
vided that it has only just begun: open the door, press and hold
starts you hear a single beep. If the door was not closed within
the ON/OFF button, the machine will switch off.

Daily Use

4sec., the alarm sound will be played. In this case, open the
Switch the machine back on using the ON/OFF button and select
door, press START/Pause button and close the door again
the new wash cycle and any desired options; Start the wash cycle
1. Check water connection
within 4 sec.
by pressing START/Pause button and closing the door within 4 sec.
Check that the dishwasher is connected to the water supply
7. END OF WASH CYCLE
and that the tap is open.
ADDING EXTRA CROCKERY
The end of the wash cycle is indicated by beeps and by the
2. Switch on the dishwasher
flashing of the wash cycle number on the display. Open the
Without switching off the machine, open the door (START/Pause
Open the door and press the ON/OFF button.
door and switch off the appliance by pressing the ON/OFF
led starts blinking) (be ware of HOT steam!) and place the
3. Load the racks (see LOADING THE RACKS)
button.
crockery inside the dishwasher. Press the START/Pause button
4. Filling the detergent dispenser
Control panel
Wait for a few minutes before removing the crockery - to avoid (see FILLING THE DETERGENT DISPENSER).
and close the door within 4 sec., the cycle will resume from the
5. Choose the program and customise the cycle
burns. Unload the racks, beginning with the lower one.
point at which it was interrupted.
Select the most appropriate program in accordance with
the type of crockery and its soiling level (see PROGRAMS
ACCIDENTAL INTERRUPTIONS

Functions

DESCRIPTION) by pressing the button
If the door is opened during the wash cycle, or if there is a power
Select the desired options (see FUNCTIONS).
cut, the cycle stops. Press the START/Pause button and close
6. Start
the door within 4 sec., the cycle will resume from the point at Start the wash cycle by pressing START/Pause button (led 1. ECO - Normally soiled crockery. Standard program, the most efficient in terms of its combined energy and water
going from flicker to lit) and closing the door within 4 sec.
which it was interrupted. consumption.
When the program starts you hear a single beep. If the door
1. On-Off/Reset button with indicator light
2. NORMAL - Mixed soil. For normally soiled dishes with dried food residues.
was not closed within 4sec., the alarm sound will be played. 2. Program selection button
3. INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used
In this case, open the door, press START/Pause button and 3. Salt refill indicator ligh
for delicate items).
4. Rinse Aid refill indicator ligh
close the door again within 4 sec.
5. Program number and delay time indicator
7. End of wash cycle
4. PRE-WASH - Use to refresh crockery planned to be washed later. No detergent to be used with this program.
6. Tablet indicator light
The end of the wash cycle is indicated by beeps and by the
5. FAST - Normally soiled crockery. Everyday cycle, that ensures optimal cleaning performance in shorter time.
flashing of the wash cycle number on the display. Open the
6. SANITIZING - Normally or heavily soiled crockery, with additional antibacterial wash. Can be used to perform
door and switch off the appliance by pressing the ON/OFF
First use
button. maintenance of the dishwasher.
Wait for a few minutes before removing the crockery - to
ADVICE REGARDING THE FIRST TIME USE
7. SELF- CLEAN - Program to be used to perform maintenance of the dishwasher. It cleans the interior of the appliance
avoid burns. Unload the racks, beginning with the lower one.
using hot water. After installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
dishes andon the machine's functional components.
• It is important that the salt reservoir be never empty.
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED � � � �rapidly 3 times
Functions
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the
and beeps will sound. The option will not be enabled.
dishwasher (see PRODUCT DESCRIPTION) and should be
filled when the SALT REFILL indicator light
HALF LOAD
HALF LOAD
control panel is lit .
If there are not many dishes to be washed, a half
If there are not many dishes to be washed, a half load
load cycle may be used in order to save water,
cycle may be used in order to save water, electricity and
electricity and detergent. Select the program and
detergent. Select the program and press the HALF LOAD
press the HALF LOAD button: the indicator light will
button: the indicator light will light up. Press the HALF
light up. Press the HALF LOAD button to deselect this
LOAD button to deselect this option.
option.
Remember to halve the amount of detergent.
Remember to halve the amount of detergent.
TABLET (Tab)
TABLET (Tab)
This setting allows you to optimize the performance
This setting allows you to optimize the performance of
of the program according to the type of detergent
the program according to the type of detergent used.
used.
Press the START/PAUSE button for 3 seconds (the
Press the START/PAUSE button for 3 seconds (the
corresponding symbol will light up) if you use combined
corresponding symbol will light up) if you use
detergents in tablet form (rinse aid, salt and detergent in
combined detergents in tablet form (rinse aid, salt
1 dose).
and detergent in 1 dose).
If you use powder or liquid detergent, this option
If you use powder or liquid detergent, this option
should be off.
should be off.
To adjust the delay time and select a shorter period of time,
press the DELAY button. To cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches off.
The DELAY function cannot be set once a wash cycle
has been started.
7
8
button.
9
11
.
1 2 3 4 5
if it has been rinsed with water before being placed in the
dishwasher, reduce the amount of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, pro-
vided that it has only just begun: open the door, press and hold
the ON/OFF button, the machine will switch off.
Switch the machine back on using the ON/OFF button and select
(Half load), fiilling up only selected racks. Incorrect loading or
overloading the dishwasher may increase resources usage the new wash cycle and any desired options; Start the wash cycle
(such as water, energy and time, as well as increase noise
by pressing START/Pause button and closing the door within 4 sec.
level), reducing cleaning and drying performance.
• Manual pre-rinsing of tableware items leads to increased
ADDING EXTRA CROCKERY
water and energy consumption and is not recommended.
Without switching off the machine, open the door (START/Pause
led starts blinking) (be ware of HOT steam!) and place the
crockery inside the dishwasher. Press the START/Pause button
and close the door within 4 sec., the cycle will resume from the
point at which it was interrupted.
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise
ACCIDENTAL INTERRUPTIONS
electricity consumption. If the crockery is only lightly soiled
If the door is opened during the wash cycle, or if there is a power
or if it has been rinsed with water before being placed in the
cut, the cycle stops. Press the START/Pause button and close
dishwasher, reduce the amount of detergent used
the door within 4 sec., the cycle will resume from the point at
accordingly.
which it was interrupted.
Modifying a running program
If a wrong program was selected, it is possible to change it,
provided that it has only just begun: open the door, press and
hold the ON/OFF button, the machine will switch off.
h
Switch the machine back on using the ON/OFF button and select
the new wash cycle and any desired options; Start the wash
cycle by pressing START/Pause button and closing the door
within 4 sec.
6 7 8 9 10 11
Adding extra crockery
7. Display
Without switching off the machine, open the door (START/
8. Half Load indicator light
Pause led starts blinking) (be ware of HOT steam!) and place the
9. Half Load button
crockery inside the dishwasher. Press the START/Pause button
10. Delay button
and close the door within 4 sec., the cycle will resume from the
11. START/Pause button with indicator light / Tab
point at which it was interrupted.
Accidental interruptions
If the door is opened during the wash cycle, or if there is a
power cut, the cycle stops. Press the START/Pause button and
close the door within 4 sec., the cycle will resume from the point
at which it was interrupted.
ENGLISH
in the
DELAY
DELAY
The start time of the program may be delayed for a
The start time of the program may be delayed for a period
period of time between 1 and 12 hours.
of time between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h»
1. Press the DELAY button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE
2. Select the wash program, press the START/PAUSE
button and within 4 seconds close the door: the timer
will begin counting down.
3. Once this time has elapsed, the indicator light «h»
3. Once this time has elapsed, the indicator light «h»
switches off and the wash cycle begins.
To adjust the delay time and select a shorter period of time,
press the DELAY button. To cancel it, press the button
repeatedly until the selected delayed start indicator light
«h» switches off.
The DELAY function cannot be set once a wash
The DELAY function cannot be set once a wash cycle
cycle has been started.
has been started.
1. Go to the Dishwasher software menu pressing and holding
button (6 sec).
2. You switched to NaturalDry Control Menu, you could change
status of NaturalDry functionality by pressing
E
– enabled
To confirm the change and exit from the Control Menu please
press and hold
Eco
1
1
1. Upper rack
2
2. � � � � � � �
3. Upper rack height adjuster
4. Upper sprayer arm
5. Lower rack
6. Cutlery basket
3
7. Lower sprayer arm
8. Filter Assembly
4
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
5
11. Rating plate
12. Control panel
6
10
3sec
1. Remove the lower rack and
unscrew the reservoir cap
(anticlockwise).
2. Only the first time you do this: fill
the salt reservoir with water.
3. Position the funnel (see figure)
and fill the salt reservoir right up
to its edge (approximately 1 kg);
it is not unusual for a little water to
leak out.
4. Remove the funnel and wipe any
salt residue away from the
TABLET (Tab)
opening.
This setting allows you to optimize the performance of
the program according to the type of detergent used.
Press the START/PAUSE button for 3 seconds (the
symbol appears on the display; each time you
corresponding symbol will light up) if you use combined
press the button, the time (1h, 2h, etc. up to max.
detergents in tablet form (rinse aid, salt and detergent in
12h) from the start of the selected wash cycle will
be increased.
1 dose).
If you use powder or liquid detergent, this option
button and within 4 seconds close the door: the
should be off.
timer will begin counting down.
switches off and the wash cycle begins. To adjust
the delay time and select a shorter period of time,
press the DELAY button. To cancel it, press the
button repeatedly until the selected delayed start
indicator light «h» switches off.
Program
d
– disabled
button (3 sec).
10
Availab
button:
options
50°
Na
Doo
whi
ens
the
As
add
tion
Nat
1. G
b
2. Y
s
E
To c
pre